Currently mac80211 determines whether HW does fragmentation
by checking whether the set_frag_threshold callback is set
or not.
However, some drivers may want to set the HW fragmentation
capability depending on HW generation.
Allow this by checking a HW flag instead of checking the
callback.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
[added the flag to ath10k and wlcore]
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Booting multiple wl12xx and wl18xx devices using the same rootfs is
a pain. You currently have to symlink the right nvs file depending
on the wl12xx type.

For example, with wl1271-nvs.bin being a symlink to wl127x-nvs.bin
by default and trying to bring up a wl128x based device:

wlcore: ERROR nvs size is not as expected: 1113 != 912
wlcore: ERROR NVS file is needed during boot
wlcore: ERROR NVS file is needed during boot
wlcore: ERROR firmware boot failed despite 3 retries

Note that wl18xx uses a separate config firmware wl18xx-conf.bin
that can be generated with tools using the following two git repos:

git.ti.com/wilink8-wlan/18xx-ti-utils
git.ti.com/wilink8-wlan/wl18xx_fw

So let's not configure the nvs file for wl18xx as it's not needed
AFAIK. If it turns out that we also need the nvs file for wl18xx,
we can just add it to the config firmware data for wl18xx.

Let's fix the issue by using the chip specific config firmware
data, and make sure we produce understandable warnings if something
is missing.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This field was added to wl_sta struct to get hw in situations
where it was not given to driver by mac80211. In our case,
get_expected_throughput op did not send hw to driver.

This patch reverts the change, as it is no longer needed due to commit
4fdbc67a ("mac80211: call get_expected_throughput only after adding
station") as hw is now sent as a parameter.
Signed-off-by: NMaxim Altshul <maxim.altshul@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.

This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Signed-off-by: NMaxim Altshul <maxim.altshul@ti.com>
[rewrite commit message, fix indentation]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Adding this opcode, allows the TI wireless driver,
to report throughput directly from FW to mac80211.

This is used mainly for mesh metric calculation.
Signed-off-by: NMaxim Altshul <maxim.altshul@ti.com>
[kvalo@codeaurora.org: fix indentation]
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

FW will provide a TX rate per link for each FW status,
and wlcore will be able to store the information for
the use of the mesh hwmp module.

This is used mainly in mesh.
Rates are reported when a mesh interface is up.
Signed-off-by: NMaxim Altshul <maxim.altshul@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

1. Added support for interface and role of mesh type.
2. Enabled enable/start of mesh-point role,
   and opening and closing a connection with a mesh peer.
3. Added multirole combination of mesh and ap
   under the same limits of dual ap mode.
4. Add support for 'sta_rc_update' opcode for mesh IF.
   The 'sta_rc_update' opcode is being used in mesh_plink.c.
Add support in wlcore to handle this opcode correctly for mesh
(as opposed to current implementation that handles STA only).
5. Bumped the firmware version to support new Mesh functionality
Signed-off-by: NMaital Hahn <maitalm@ti.com>
Signed-off-by: NYaniv Machani <yanivma@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)

TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since stations can now be added before association
(NL80211_FEATURE_FULL_AP_CLIENT_STATE support),
no supported rates are set when the station is added
to the fw, resulting in fw recovery.

Fix it by first configuring the AP basic rates as
the station configured rates (when the station is
first added to the driver), and after the station
was authorized re-configure it, now with the actual
supported rates.
Signed-off-by: NGuy Mishol <guym@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use to_delayed_work() instead of open-coding it.
Signed-off-by: NGeliang Tang <geliangtang@163.com>
[Update commit message]
Signed-off-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When working with AP + P2P, it's possible to get into
a state when the AP is in ROC (due to assiciating station)
while trying to ROC on the P2P interface.

Replace the WARN_ON with wl1271_error to avoid warnings
in this case.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Enable the FW Logger to work over the SDIO interface in addition to over UART
interface. In the new design we use fw internal memory instead of packet ram
that was used in older (wl12xx) design. This change reduces the impact on TP
and stability.

A new event was added to notify fw logger is ready for reading. Dynamic
configuration to debugfs was added as well.
Signed-off-by: NShahar Patury <shaharp@ti.com>
Signed-off-by: NGuy Mishol <guym@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When starting a p2p mgmt interface, enable its device role. This
allows us to keep the sta role disabled and scan on the dev role.

In general, p2p management interfaces cannot send vif-specific commands
to FW, as the vif role id is invalid. Only off-channel data and scans
happen on this vif, so most ops are not relevant.

If the vif is a p2p mgmt vif, block some mac80211 ops.

Configure rate policies for p2p mgmt interface, as
otherwise p2p packets come out with arbitrary rates.

Since wpa_supplicant currently doesn't support standalone
p2p device mode (without another attached managed interface),
add p2p device to the allowed interface combinations without
decreasing the allowed station count.

Moreover, increase the station count in some cases, as AP
mode usually starts as station interface, and the AP interface
is now different from the p2p management one).
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.

This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.

The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

* Interrupt request need to happen when the wilink chip is powered on and
  driving the wlan_irq line. This avoids spurious interrupt issues that
  are a result of different external pulls configuration on different
  platforms
* Allow working with wl18xx level-low and falling edge irqs by configuring
  wl18xx to invert the device interrupt
Signed-off-by: NEyal Reizer <eyalr@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.

Removing it removes a lot of corner cases.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The driver can clearly enable fast-xmit since it does rate
control in the device and thus must do duration calculation
there as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Now that we have wlcore device-tree bindings in place
(for both wl12xx and wl18xx), remove the legacy
wl12xx_platform_data struct, and move its members
into the platform device data (that is passed to wlcore)

Davinci 850 is the only platform that still set
the platform data in the legacy way (and doesn't
have DT bindings), so remove the relevant
code/Kconfig option from the board file (as suggested
by Sekhar Nori)

Since no one currently uses wlcore_spi, simply remove its
platform data support (DT bindings will have to be added
if someone actually needs it)
Signed-off-by: NLuciano Coelho <luca@coelho.fi>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
Acked-by: NKalle Valo <kvalo@codeaurora.org>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The platform_quirk element in the platform data was used
to change the way the IRQ is triggered.  When set,
the EDGE_IRQ quirk would change the irqflags used
and treat edge trigger differently from the rest.

Instead of hiding this irq flag setting behind the quirk,
have the board files set the irq_trigger explicitly.

This will allow us to use standard irq DT definitions
later on.
Signed-off-by: NLuciano Coelho <luca@coelho.fi>
[Eliad - rebase, add irq_trigger field and pass it,
update board file changes]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
Acked-by: NKalle Valo <kvalo@codeaurora.org>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We recently introduced a new error path which needs an unlock.

Fixes: 6d5a748d ('wlcore: add ability to reduce FW interrupts during suspend')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add dfs region to the reg domain channel update command.
Signed-off-by: NGuy Mishol <guym@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since we are going to support dfs channels, there
is no reason to mark them as NO_IR (having
the DFS flag is enough anyway).

Additionally, when setting the regdomain configuration,
enable usable dfs channels.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

call wlcore_cmd_dfs_master_restart when starting
the ap on a new channel (after csa is done).

Add a new WLVIF_FLAG_BEACON_DISABLED flag to
indicate that dfs_master_restart command
is required.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Support ap csa support by implementing the channel_switch_beacon()
mac80211 op.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add support for CAC start/stop commands, and pass
radar detection events from the fw to mac80211.

Bump fw name (to wl18xx-fw-4.bin) and min fw version
(to 8.9.*.*.11), and align event mailbox accordingly.
Signed-off-by: NGuy Mishol <guym@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

configure wowlan when host is suspended in AP mode,
since the FW can now wake the host up on Rx.
Signed-off-by: NKobi Leibovitch <kobi.lev100@gmail.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the ability to mask FW interrupts on RX BA activity, PSM
entry/exit and fast-link notifications. This is used when the host
is suspended in order to decrease redundant wake ups.
Signed-off-by: NRam Amrani <ramrani@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

sta_rc_update runs in atomic context. thus, a new work
should be scheduled in order to configure the fw
with the required configuration.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is really just duplicating the list of information that's
already available in the nl80211 attribute, so remove the list.
Two small changes are needed:
 * remove STATION_INFO_ASSOC_REQ_IES complete, but the length
   (assoc_req_ies_len) can be used instead
 * add NL80211_STA_INFO_RX_DROP_MISC which exists internally
   but not in nl80211 yet

This gets rid of the duplicate maintenance of the two lists.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In many cases, drivers can filter things like beacons that will
skew statistics reported by mac80211. To get correct statistics
in these cases, call drivers to obtain statistics and let them
override all values, filling values from mac80211 if the driver
didn't provide them. Not all of them make sense for the driver
to fill, so some are still always done by mac80211.

Note that this doesn't currently allow a driver to say "I know
this value is wrong, don't report it at all", or to sum it up
with a mac80211 value (as could be useful for "dropped misc"),
that can be added if it turns out to be needed.

This also gets rid of the get_rssi() method as is can now be
implemented using sta_statistics().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Channel switch with multiple channel contexts should now work fine.
Remove check that disallows switches when multiple contexts are in
use.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The *_bit operations expect unsigned longs.
Instead of casting the pointers, simply define various
bitmaps as unsigned long (instead of u32).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sending the FW a channel switch command on a disconnected
vif may result in a beacon loss event. Avoid this corner case.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All the smart config code is in place now,
so register the relevant vendor commands.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

we don't have any actual limitation in the driver, so
increase it arbitrarily to 30 seconds.

The long ROC is needed for the smart config.flow.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The LAA bit is second bit of the MSB, not of the
third byte.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>