clk_get() needs to also perform an IS_ERR() check to see whether
clk_get_sys() failed or not.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This stubs in clk_get_sys() from the ARM clkdev implementation.
Tentatively conver the clk_get() lookup code to use this, and once the
rest of the in-tree users are happy with this, it can replace the
fallback lookups.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The only user for this is the SH-Mobile r_clk, which is now added as a
root clock and can be kicked via propagate_rate() as usual. Given that,
there is no longer any need for the special clk_recalc_rate(), so we kill
it off.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This tidies up the set_rate hack that the on-chip clocks were abusing to
trigger rate propagation, which is now handled generically.

Additionally, now that CLK_ENABLE_ON_INIT is wired up where it needs to
be for these clocks, the clk_enable() can go away. In some cases this was
bumping up the refcount higher than it should have been.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This causes the generic clk_set_parent() implementation to be a bit more
intelligent. A clk_reparent() is added to move the clock over to the new
parent's sibling list, which then allows the generic rate propagation
code to succeed. This also becomes a nop if the new and old parents are
unchanged.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There are a couple of instances where a clk_enable() can fail, which the
SH-Mobile code presently handles, but doesn't get reported all the way
back up. This fixes up the return type so the errors make it all the way
down to the drivers.

Additionally, we now also error out properly if the parent enable fails.
Prep work for aggressively turning off unused clocks on boot.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Kill off all of the clk_always_enabled leftovers and use the new flag
directly.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There is no real distinction here in behaviour, either a clock needs to
be enabled on initialiation or not. The ALWAYS_ENABLED flag was always
intended to only apply to clocks that were physically always on and could
simply not be disabled at all from software. Unfortunately over time this
was abused and the meaning became a bit blurry.

So, we kill off both of all of those paths now, as well as the newer
NEEDS_INIT flag, and consolidate on a CLK_ENABLE_ON_INIT. Clocks that
need to be enabled on initialization can set this, and it will purposely
enable them and bump the refcount up.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This resyncs the rate propagation strategy with the scheme used by the
OMAP clock framework. Child clocks are tracked on a list under each
parent and propagation happens there specifically rather than constantly
iterating over the global clock list.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds a followparent_recalc() helper for clocks that just follow the
parent's rate. Switch over the few CPUs that use this scheme for some of
their clocks.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is prep work for cleaning up some of the rate propagation bits.
Trivial conversion.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds TMU platform data for sh7780. Both clockevent
and clocksource support is enabled.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update the r7780 highlander defconfig to fix
PCLK value, while at it fix cmdline on r7785.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.

This fixes potential irq masking issues for sh7760 hardware
blocks such as DMAC/TMU2/REF.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds TMU platform data for sh7760. Both clockevent
and clocksource support is enabled.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds TMU platform data for sh775x. Both clockevent
and clocksource support is enabled.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Include empty_zero_page in _text. This fixes a problem
introduced by c3e2586b
which results in broken boot on R2D-Plus.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This fixes up the broken I2C offset in 32-bit mode.
The cause is because the board datasheet had a mistake.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

In the case where we fall back on the generic jiffies clocksource,
INITIAL_JIFFIES needs to be accounted for so that printk times aren't
completely skewed.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

.init_ramfs ought to be .init.ramfs, fix it up.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There is nothing in these routines that inherently depends on R0 use.
Given that these routines are inlined, it is rather easy to blow up the
compiler by exhausting the spill class when performing a 64-bit swab.

This presently manifests itself as the following:

CC      fs/ocfs2/suballoc.o
fs/ocfs2/suballoc.c: In function 'ocfs2_reserve_suballoc_bits':
fs/ocfs2/suballoc.c:638: error: unrecognizable insn:
(insn 2793 1230 1231 103 arch/sh/include/asm/swab.h:33 (set (reg:HI 853)
        (subreg:HI (reg:SI 149 macl) 2)) -1 (expr_list:REG_DEAD (reg:SI 149 macl)
        (nil)))
fs/ocfs2/suballoc.c:638: internal compiler error: in extract_insn, at recog.c:1991

This patch switches over to using an arbitrarily assigned register instead.

While the same issue does not exist in the SH-5 case, there is likewise no harm
in having an alternate register used for the byterev/shari pair.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This implements a simple case that just iterates through the common
cases, looking at UTS_MACHINE for hints.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Consolidate these in a single place in the Kconfig menus. At the same
time, disable their interactivity and set them according to the board
config defaults.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This kills off the _64 variant and moves the _32 one over as the generic
one to use.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This introduces a BITS export that can handily be picked up by Makefiles
for cleaner sharing. Reflect its use in arch/sh/boot/compressed/ in
preparation for unifying the Makefiles.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Tie this in to the Makefile directly, where we already know what we are
running on. This tidies up the linker script a bit, and is prep work for
unifying the arch/sh/boot/compressed linker scripts.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Just forcefully rename the _32 variant overtop, and kill off the now
unused _64 version.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds all of the requisite bits from vmlinux_64.lds.S in to the _32
variant, resulting in a unified and generic linker script that can be
shared across both.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This fixes up the LSB setting for SHmedia branching in updated symbols
when processing module relocations.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Newer code paths that are heavier in 64-bit math manage to get this
generated by newer compilers, provide a definition and export
accordingly. This is trivially wrapped around the existing __sdivsi3
code.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is now clashing with a driver, so just rename it.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

These are presently only defined for sh32, use the plain unoptimized
versions for sh64. Fixes up smsc911x build.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

sci_rxd_in() on SH-5 wants to be using SCSPTR, not SCSPTR2.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPeter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPeter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKieran Bingham <kieranbingham@gmail.com>
Signed-off-by: NPeter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Plugs in PT_TEXT_END_ADDR/PT_TEXT_ADDR/PT_DATA_ADDR/PT_TEXT_LEN
definitions.
Signed-off-by: NKieran Bingham <kieranbingham@gmail.com>
Signed-off-by: NPeter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>