This implements a very basic I2C host driver for the BCM2835 SoC. Missing
features so far are:

* 10-bit addressing.
* DMA.
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Adding Seth Heasley and Myself as maintainers for the i2c-ismt drvier
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: N"Heasley, Seth" <seth.heasley@intel.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

This patch corrects checkpatch errors.

The changes has also been removed as it has less meaning with version
control tools.
Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

This patch corrects the display of the acpi_base unsigned hex value.
Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

This patch replaces hexadecimal values by constants for SMBus commands.
Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Datasheet on collision:
	SMBus Collision (SMBCOL_STS)
	This bit is set when a SMBus Collision condition occurs and
	SMBus Host loses in the bus arbitration. The software should
	clear this bit and re-start SMBus operation.

As the status will be cleared in transaction_end, we can remove the
sis630_write and prepare to return -EAGAIN to retry.
Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

The sticky bits must be cleared at the end of the transaction by writing
a 1 to all fields.

Datasheet:
	SMBus Status (SMB_STS)
	The following registers are all sticky bits and only can be
	cleared by writing a one to their corresponding fields.
Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

It was observed the Host Clock Divider was not written by the driver. It
was still set to (default) 0, if not already set by BIOS, which caused
garbage on SMBus.
This driver adds a parameters which is used to calculate the divider
appropriately for a default bitrate of 100 KHz. This new divider is only
applied if the clock divider is still default 0.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Commit 70d46a24 "i2c: at91: add dt support to i2c-at91"
added DT only support for at91sam9x5. Building i2c-at91
without CONFIG_OF now warns about at91sam9x5_config as
being unused.

  drivers/i2c/busses/i2c-at91.c:556:30: warning: 'at91sam9x5_config' defined but not used [-Wunused-variable]

Move at91sam9x5_config under the defined(CONFIG_OF)
guard as new AT91 SoCs will be DT only.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

The iSMT (Intel SMBus Message Transport) supports multi-master I2C/SMBus,
as well as IPMI.  It's operation is DMA-based and utilizes descriptors to
initiate transactions on the bus.

The iSMT hardware can act as both a master and a target, although this
driver only supports being a master.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NBill Brown <bill.e.brown@intel.com>
Tested-by: NSeth Heasley <seth.heasley@intel.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

By default there should be no stop bit on I2C between single messages
within transfers. Fix the driver to comply and only send a stop bit at
the end of transfers or if I2C_M_STOP is set.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Eliminate an open-coded "goto" loop by introducing a function.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

In a timeout case return an error immediately from the driver's
.master_xfer() method, instead of continuing and letting higher layers
fail.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Reduce 2 boolean functions from "if (condition) return 1; return 0;" to
"return condition;"
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

This patch drops the i2c timing tables from this driver and instead
derives the timing based from the requested clock sleep. The timing
tables were completely wrong anyway when observed on a scope.

This new algorithm is also only derived by using a scope, but it seems
to produce much more accurate result.
Signed-off-by: NMarek Vasut <marex@denx.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
[wsa: changed messages from dev_err to dev_warn]
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

This patch adds the PCU SMBus DeviceID for the Intel Avoton SOC.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Signed-off-by: NGiridhar Maruthy <giridhar.m@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Add support for the PIO mode and mixed PIO/DMA mode support. The mixed
PIO/DMA is the default mode of operation. This shall leverage overhead
that the driver creates due to setting up DMA descriptors even for very
short transfers.

The current boundary between PIO/DMA 8 bytes, transfers shorter than 8
bytes are transfered by PIO, longer transfers use DMA. The performance
of write transfers remains unchanged, while there is a minor improvement
of read performance. Reading 16KB EEPROM with DMA-only operations gives
a read speed of 39.5KB/s, while with then new mixed-mode the speed is
blazing 40.6KB/s.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

err_cpufreq label is now used only once. It can be removed and related
code can be moved to the caller location.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

In i2c-s3c2410 driver probe, only s3c24xx_i2c_init() needs the I2C clock
to be enabled. Moving clk_prepare_enable() and clk_disable_unprepare()
calls to around this function simplifies the return path of probe call.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

i2c-s3c2410 driver is modified to use devm_clk_get()
and devm_request_irq(). This also simplifies the
return path in driver's probe.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

err_noclk label redirects to a simple return statement. Move the
return statement to the caller location and remove the label.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

cppcheck rightfully reports those as "reassigned a value before the old
one has been used."
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>

Amend the I2C nomadik pin controller to optionally take a pin control
handle and set the state of the pins to:

- "default" on boot, resume and before performing an i2c transfer
- "idle" after initial default, after resume default, and after each
   i2c xfer
- "sleep" on suspend()

This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle, and for runtime cases inbetween
I2C transfers.
Signed-off-by: NPatrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
[wsa: fixed braces on one else-branch]
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NLudovic Ddesroches <ludovic.desroches@atmel.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

NVIDIA's Tegra114 has following enhanced feature in i2c controller:
- Enable/disable control for per packet transfer complete interrupt.
  Earlier SoCs could not disable this.
- Single clock source for standard/fast and HS mode clock speed.
  The clock divisor for fast/standard mode is added into the i2c
  controller to meet the HS and standard/fast mode of clock speed
  from single source.

Add support for the above feature to make it functional on T114 SOCs.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Intel Lynxpoint has two I2C controllers. These controllers are enumerated
from ACPI namespace with IDs INT33C2 and INT33C3. Add support for these to
the I2C DesignWare platform driver.

This is based on the work of Dirk Brandewie.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

In order to save power the device should be put to low power states
whenever it is not being used. We implement this by enabling minimal
runtime PM support.

There isn't much to do for the device itself as it is disabled once the
last transfer is completed but subsystem/domain runtime PM hooks can save
more power by power gating the device etc.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

If IC_EMPTYFIFO_HOLD_MASTER_EN is set to one, the DesignWare I2C controller
doesn't generate STOP on the bus when the FIFO is empty. This violates the
rules of Linux I2C stack as it requires that the STOP is issued once the
i2c_transfer() is finished.

However, there is no way to detect this from the hardware registers, so we
must make sure that the STOP bit is always set once the last byte of the
last message is transferred.

This patch is based on the work of Dirk Brandewie.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

avoid these checkpatch.pl issues :
- ERROR: "foo * bar" should be "foo *bar"
- ERROR: switch and case should be at the same indent
- ERROR: "(foo*)" should be "(foo *)"
- ERROR: do not use assignment in if condition
- ERROR: space required before the open parenthesis '('
- WARNING: suspect code indent for conditional statements
- WARNING: quoted string split across lines
- WARNING: space prohibited between function name and open parenthesis '('
- WARNING: line over 80 characters
also add spaces around some "+", "=", "*"
Signed-off-by: NLaurent Navet <laurent.navet@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

As the at24 driver is able handle a bunch of serial storage chips other than
EEPROMs this is now mentioned in Kconfig.
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

i2c_smbus_process_call has no users in the kernel, so this can be
removed. Documentation for the same has been updated accordingly.

Fixes following sparse warning.
drivers/i2c/i2c-core.c:1871:5: warning: symbol 'i2c_smbus_process_call'
was not declared. Should it be static?

[wsa: updated the documentation]
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Pull btrfs fixes from Chris Mason:
 "It turns out that we had two crc bugs when running fsx-linux in a
  loop.  Many thanks to Josef, Miao Xie, and Dave Sterba for nailing it
  all down.  Miao also has a new OOM fix in this v2 pull as well.

  Ilya fixed a regression Liu Bo found in the balance ioctls for pausing
  and resuming a running balance across drives.

  Josef's orphan truncate patch fixes an obscure corruption we'd see
  during xfstests.

  Arne's patches address problems with subvolume quotas.  If the user
  destroys quota groups incorrectly the FS will refuse to mount.

  The rest are smaller fixes and plugs for memory leaks."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (30 commits)
  Btrfs: fix repeated delalloc work allocation
  Btrfs: fix wrong max device number for single profile
  Btrfs: fix missed transaction->aborted check
  Btrfs: Add ACCESS_ONCE() to transaction->abort accesses
  Btrfs: put csums on the right ordered extent
  Btrfs: use right range to find checksum for compressed extents
  Btrfs: fix panic when recovering tree log
  Btrfs: do not allow logged extents to be merged or removed
  Btrfs: fix a regression in balance usage filter
  Btrfs: prevent qgroup destroy when there are still relations
  Btrfs: ignore orphan qgroup relations
  Btrfs: reorder locks and sanity checks in btrfs_ioctl_defrag
  Btrfs: fix unlock order in btrfs_ioctl_rm_dev
  Btrfs: fix unlock order in btrfs_ioctl_resize
  Btrfs: fix "mutually exclusive op is running" error code
  Btrfs: bring back balance pause/resume logic
  btrfs: update timestamps on truncate()
  btrfs: fix btrfs_cont_expand() freeing IS_ERR em
  Btrfs: fix a bug when llseek for delalloc bytes behind prealloc extents
  Btrfs: fix off-by-one in lseek
  ...

Pull cifs fixes from Steve French:
 "Two small cifs fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  fs/cifs/cifs_dfs_ref.c: fix potential memory leakage
  cifs: fix srcip_matches() for ipv6

Pull kvm fixlet from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: Emulate dcbf

Pull ARM fixes from Russell King:
 "A number of fixes:

  Patrik found a problem with preempt counting in the VFP assembly
  functions which can cause the preempt count to be upset.

  Nicolas fixed a problem with the parsing of the DT when it straddles a
  1MB boundary.

  Subhash Jadavani reported a problem with sparsemem and our highmem
  support for cache maintanence for DMA areas, and TI found a bug in
  their strongly ordered memory mapping type.

  Also, three fixes by way of Will Deacon's tree from Dave Martin for
  instruction compatibility and Marc Zyngier to fix hypervisor boot mode
  issues."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7629/1: mm: Fix missing XN flag for for MT_MEMORY_SO
  ARM: DMA: Fix struct page iterator in dma_cache_maint() to work with sparsemem
  ARM: 7628/1: head.S: map one extra section for the ATAG/DTB area
  ARM: 7627/1: Predicate preempt logic on PREEMP_COUNT not PREEMPT alone
  ARM: virt: simplify __hyp_stub_install epilog
  ARM: virt: boot secondary CPUs through the right entry point
  ARM: virt: Avoid bx instruction for compatibility with <=ARMv4

Pull ARM SoC fixes from Olof Johansson:
 "Here's a long-pending fixes pull request for arm-soc (I didn't send
  one in the -rc4 cycle).

  The larger deltas are from:

   - A fixup of error paths in the mvsdio driver

   - Header file move for a driver that hadn't been properly converted
     to multiplatform on i.MX, which was causing build failures when
     included

   - Device tree updates for at91 dealing mostly with their new pinctrl
     setup merged in 3.8 and mistakes in those initial configs

  The rest are the normal mix of small fixes all over the place; sunxi,
  omap, imx, mvebu, etc, etc."

* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
  mfd: vexpress-sysreg: Don't skip initialization on probe
  ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
  ARM: vexpress: extend the MPIDR range used for pen release check
  ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
  ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
  ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
  ARM: at91/dts: add macb mii pinctrl config for kizbox
  ARM: at91: rm9200: remake the BGA as default version
  ARM: at91: fix gpios on i2c-gpio for RM9200 DT
  ARM: at91/at91sam9x5 DTS: add SCK USART pins
  ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
  ARM: at91/at91-pinctrl documentation: fix typo and add some details
  ARM: kirkwood: fix missing #interrupt-cells property
  mmc: mvsdio: use devm_ API to simplify/correct error paths.
  clk: mvebu/clk-cpu.c: fix memory leakage
  ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
  ARM: OMAP2+: DT node Timer iteration fix
  ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
  ARM: OMAP2+: fix build break for omapdrm
  ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
  ...

Pull ACPI and power management fixes from Rafael Wysocki:

 - Two cpuidle initialization fixes from Konrad Rzeszutek Wilk.

 - cpufreq regression fixes for AMD processors from Borislav Petkov,
   Stefan Bader, and Matthew Garrett.

 - ACPI cpufreq fix from Thomas Schlichter.

 - cpufreq and devfreq fixes related to incorrect usage of operating
   performance points (OPP) framework and RCU from Nishanth Menon.

 - APEI workaround for incorrect BIOS information from Lans Zhang.

* tag 'pm+acpi-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: Add module aliases for acpi-cpufreq
  ACPI: Check MSR valid bit before using P-state frequencies
  PM / devfreq: exynos4_bus: honor RCU lock usage
  PM / devfreq: add locking documentation for recommended_opp
  cpufreq: cpufreq-cpu0: use RCU locks around usage of OPP
  cpufreq: OMAP: use RCU locks around usage of OPP
  ACPI, APEI: Fixup incorrect 64-bit access width firmware bug
  ACPI / processor: Get power info before updating the C-states
  powernow-k8: Add a kconfig dependency on acpi-cpufreq
  ACPI / cpuidle: Fix NULL pointer issues when cpuidle is disabled
  intel_idle: Don't register CPU notifier if we are not running.