In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.

It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.

Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.

Fixes: 606f3993
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: NAlexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 98e3862c ("kcm: fix 0-length case for kcm_sendmsg()")
I tried to avoid skb allocation for 0-length case, but missed
a check for NULL pointer in the non EOR case.

Fixes: 98e3862c ("kcm: fix 0-length case for kcm_sendmsg()")
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: NRui Sousa <rui.sousa@nxp.com>
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jonathan T. Leighton says:

====================
IPv4-mapped on wire, :: dst address issue

Under some circumstances IPv6 datagrams are sent with IPv4-mapped IPv6
addresses as the source. Given an IPv6 socket bound to an IPv4-mapped
IPv6 address, and an IPv6 destination address, both TCP and UDP will
will send packets using the IPv4-mapped IPv6 address as the source. Per
RFC 6890 (Table 20), IPv4-mapped IPv6 source addresses are not allowed
in an IP datagram. The problem can be observed by attempting to
connect() either a TCP or UDP socket, or by using sendmsg() with a UDP
socket. The patch is intended to correct this issue for all socket
types.

linux follows the BSD convention that an IPv6 destination address
specified as in6addr_any is converted to the loopback address.
Currently, neither TCP nor UDP consider the possibility that the source
address is an IPv4-mapped IPv6 address, and assume that the appropriate
loopback address is ::1. The patch adds a check on whether or not the
source address is an IPv4-mapped IPv6 address and then sets the
destination address to either ::ffff:127.0.0.1 or ::1, as appropriate.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a check on the type of the source address for the case
where the destination address is in6addr_any. If the source is an
IPv4-mapped IPv6 source address, the destination is changed to
::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This
is done in three locations to handle UDP calls to either connect() or
sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays
handling an in6addr_any destination until very late, so the patch only
needs to handle the case where the source is an IPv4-mapped IPv6
address.
Signed-off-by: NJonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a check for the problematic case of an IPv4-mapped IPv6
source address and a destination address that is neither an IPv4-mapped
IPv6 address nor in6addr_any, and returns an appropriate error. The
check in done before returning from looking up the route.
Signed-off-by: NJonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When called by HW offloading drivers, the TC action (e.g
net/sched/act_mirred.c) code uses this_cpu logic, e.g

 _bstats_cpu_update(this_cpu_ptr(a->cpu_bstats), bytes, packets)

per the kernel documention, preemption should be disabled, add that.

Before the fix, when running with CONFIG_PREEMPT set, we get a

BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793

asserion from the TC action (mirred) stats_update callback.

Fixes: aad7e08d ('net/mlx5e: Hardware offloaded flower filter statistics support')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Herbert Xu says:

====================
rhashtable: Handle table allocation failure during insertion

v2 -

Added Ack to patch 2.
Fixed RCU annotation in code path executed by rehasher by using
rht_dereference_bucket.

v1 -

This series tackles the problem of table allocation failures during
insertion.  The issue is that we cannot vmalloc during insertion.
This series deals with this by introducing nested tables.

The first two patches removes manual hash table walks which cannot
work on a nested table.

The final patch introduces nested tables.

I've tested this with test_rhashtable and it appears to work.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code that handles GFP_ATOMIC kmalloc failure on
insertion.  As we cannot use vmalloc, we solve it by making our
hash table nested.  That is, we allocate single pages at each level
and reach our desired table size by nesting them.

When a nested table is created, only a single page is allocated
at the top-level.  Lower levels are allocated on demand during
insertion.  Therefore for each insertion to succeed, only two
(non-consecutive) pages are needed.

After a nested table is created, a rehash will be scheduled in
order to switch to a vmalloced table as soon as possible.  Also,
the rehash code will never rehash into a nested table.  If we
detect a nested table during a rehash, the rehash will be aborted
and a new rehash will be scheduled.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two problems with the function tipc_sk_reinit.  Firstly
it's doing a manual walk over an rhashtable.  This is broken as
an rhashtable can be resized and if you manually walk over it
during a resize then you may miss entries.

Secondly it's missing memory barriers as previously the code used
spinlocks which provide the barriers implicitly.

This patch fixes both problems.

Fixes: 07f6c4bc ("tipc: convert tipc reference table to...")
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function glock_hash_walk walks the rhashtable by hand.  This
is broken because if it catches the hash table in the middle of
a rehash, then it will miss entries.

This patch replaces the manual walk by using the rhashtable walk
interface.

Fixes: 88ffbf3e ("GFS2: Use resizable hash table for glocks")
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sending ARP requests over AX.25 links the hwaddress in the neighbour
cache are not getting initialized.  For such an incomplete arp entry
ax2asc2 will generate an empty string resulting in /proc/net/arp output
like the following:

$ cat /proc/net/arp
IP address       HW type     Flags       HW address            Mask     Device
192.168.122.1    0x1         0x2         52:54:00:00:5d:5f     *        ens3
172.20.1.99      0x3         0x0              *        bpq0

The missing field will confuse the procfs parsing of arp(8) resulting in
incorrect output for the device such as the following:

$ arp
Address                  HWtype  HWaddress           Flags Mask            Iface
gateway                  ether   52:54:00:00:5d:5f   C                     ens3
172.20.1.99                      (incomplete)                              ens3

This changes the content of /proc/net/arp to:

$ cat /proc/net/arp
IP address       HW type     Flags       HW address            Mask     Device
172.20.1.99      0x3         0x0         *                     *        bpq0
192.168.122.1    0x1         0x2         52:54:00:00:5d:5f     *        ens3

To do so it change ax2asc to put the string "*" in buf for a NULL address
argument.  Finally the HW address field is left aligned in a 17 character
field (the length of an ethernet HW address in the usual hex notation) for
readability.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an issue where the type of counters in the queue(s)
and interface are not in sync (queue counters are int, interface
counters are long), causing incorrect reporting of tx/rx values
of the vif interface and unclear counter overflows.
This patch sets both counters to the u64 type.
Signed-off-by: NMart van Santen <mart@greenhost.nl>
Reviewed-by: NPaul Durrant <paul.durrant@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ghostprotocols.net domain is not working, remove it from CREDITS and
MAINTAINERS, and change the status to "Odd fixes", and since I haven't
been maintaining those, remove my address from there.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems nobody used LLC since linux-3.12.

Fortunately fuzzers like syzkaller still know how to run this code,
otherwise it would be no fun.

Setting skb->sk without skb->destructor leads to all kinds of
bugs, we now prefer to be very strict about it.

Ideally here we would use skb_set_owner() but this helper does not exist yet,
only CAN seems to have a private helper for that.

Fixes: 376c7311 ("net: add a temporary sanity check in skb_orphan()")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NAndrey Konovalov <andreyknvl@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If BPF_F_ALLOW_OVERRIDE flag is used in BPF_PROG_ATTACH command
to the given cgroup the descendent cgroup will be able to override
effective bpf program that was inherited from this cgroup.
By default it's not passed, therefore override is disallowed.

Examples:
1.
prog X attached to /A with default
prog Y fails to attach to /A/B and /A/B/C
Everything under /A runs prog X

2.
prog X attached to /A with allow_override.
prog Y fails to attach to /A/B with default (non-override)
prog M attached to /A/B with allow_override.
Everything under /A/B runs prog M only.

3.
prog X attached to /A with allow_override.
prog Y fails to attach to /A with default.
The user has to detach first to switch the mode.

In the future this behavior may be extended with a chain of
non-overridable programs.

Also fix the bug where detach from cgroup where nothing is attached
was not throwing error. Return ENOENT in such case.

Add several testcases and adjust libbpf.

Fixes: 30070984 ("cgroup: add support for eBPF programs")
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NTejun Heo <tj@kernel.org>
Acked-by: NDaniel Mack <daniel@zonque.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The failure path in ibmvnic_open() mistakenly makes a second call
to napi_enable instead of calling napi_disable. This can result
in a BUG_ON for any queues that were enabled in the previous call
to napi_enable.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize condition variables prior to invoking any work that can
mark them complete. This resolves a race in the ibmvnic driver where
the driver faults trying to complete an uninitialized condition
variable.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) If the timing is wrong we can indefinitely stop generating new ipv6
    temporary addresses, from Marcus Huewe.

 2) Don't double free per-cpu stats in ipv6 SIT tunnel driver, from Cong
    Wang.

 3) Put protections in place so that AF_PACKET is not able to submit
    packets which don't even have a link level header to drivers. From
    Willem de Bruijn.

 4) Fix memory leaks in ipv4 and ipv6 multicast code, from Hangbin Liu.

 5) Don't use udp_ioctl() in l2tp code, UDP version expects a UDP socket
    and that doesn't go over very well when it is passed an L2TP one.
    Fix from Eric Dumazet.

 6) Don't crash on NULL pointer in phy_attach_direct(), from Florian
    Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  l2tp: do not use udp_ioctl()
  xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()
  NET: mkiss: Fix panic
  net: hns: Fix the device being used for dma mapping during TX
  net: phy: Initialize mdio clock at probe function
  igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()
  xen-netfront: Improve error handling during initialization
  sierra_net: Skip validating irrelevant fields for IDLE LSIs
  sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications
  kcm: fix 0-length case for kcm_sendmsg()
  xen-netfront: Rework the fix for Rx stall during OOM and network stress
  net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()
  net: thunderx: Fix PHY autoneg for SGMII QLM mode
  net: dsa: Do not destroy invalid network devices
  ping: fix a null pointer dereference
  packet: round up linear to header len
  net: introduce device min_header_len
  sit: fix a double free on error path
  lwtunnel: valid encap attr check should return 0 when lwtunnel is disabled
  ipv6: addrconf: fix generation of new temporary addresses

Pull rdma fixes from Doug Ledford:
 "Third round of -rc fixes for 4.10 kernel:

   - two security related issues in the rxe driver

   - one compile issue in the RDMA uapi header"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  RDMA: Don't reference kernel private header from UAPI header
  IB/rxe: Fix mem_check_range integer overflow
  IB/rxe: Fix resid update

Pull i2c bugfixes from Wolfram Sang:
 "Two bugfixes (proper IO mapping and use of mutex) for a driver feature
  we introduced in this cycle"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: piix4: Request the SMBUS semaphore inside the mutex
  i2c: piix4: Fix request_region size

Pull MMC host fix from Ulf Hansson:
 "mmci: Fix hang while waiting for busy-end interrupt"

* tag 'mmc-v4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: mmci: avoid clearing ST Micro busy end interrupt mistakenly

Pull sound fixes from Takashi Iwai:
 "Here are some last-minute fixes: two fixes for races in ALSA sequencer
  queue spotted by syzkaller, a revert for a regression of LINE6 driver
  (since 4.9), and a trivial new codec ID addition for Nvidia HDMI"

* tag 'sound-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - adding a new NV HDMI/DP codec ID in the driver
  ALSA: seq: Fix race at creating a queue
  Revert "ALSA: line6: Only determine control port properties if needed"
  ALSA: seq: Don't handle loop timeout at snd_seq_pool_done()

Pull nfsd revert from Bruce Fields:
 "This patch turned out to have a couple problems. The problems are
  fixable, but at least one of the fixes is a little ugly. The original
  bug has always been there, so we can wait another week or two to get
  this right"

* tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux:
  nfsd: Revert "nfsd: special case truncates some more"

Pull powerpc fixes friom Michael Ellerman:
 "Apologies for the late pull request, but Ben has been busy finding bugs.

   - Userspace was semi-randomly segfaulting on radix due to us
     incorrectly handling a fault triggered by autonuma, caused by a
     patch we merged earlier in v4.10 to prevent the kernel executing
     userspace.

   - We weren't marking host IPIs properly for KVM in the OPAL ICP
     backend.

   - The ERAT flushing on radix was missing an isync and was incorrectly
     marked as DD1 only.

   - The powernv CPU hotplug code was missing a wakeup type and failing
     to flush the interrupt correctly when using OPAL ICP

  Thanks to Benjamin Herrenschmidt"

* tag 'powerpc-4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv: Properly set "host-ipi" on IPIs
  powerpc/powernv: Fix CPU hotplug to handle waking on HVI
  powerpc/mm/radix: Update ERAT flushes when invalidating TLB
  powerpc/mm: Fix spurrious segfaults on radix with autonuma

udp_ioctl(), as its name suggests, is used by UDP protocols,
but is also used by L2TP :(

L2TP should use its own handler, because it really does not
look the same.

SIOCINQ for instance should not assume UDP checksum or headers.

Thanks to Andrey and syzkaller team for providing the report
and a nice reproducer.

While crashes only happen on recent kernels (after commit
7c13f97f ("udp: do fwd memory scheduling on dequeue")), this
probably needs to be backported to older kernels.

Fixes: 7c13f97f ("udp: do fwd memory scheduling on dequeue")
Fixes: 85584672 ("udp: Fix udp_poll() and ioctl()")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NAndrey Konovalov <andreyknvl@google.com>
Acked-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
CC: stable@vger.kernel.org
Reviewed-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a USB-to-serial adapter is unplugged, the driver re-initializes, with
dev->hard_header_len and dev->addr_len set to zero, instead of the correct
values.  If then a packet is sent through the half-dead interface, the
kernel will panic due to running out of headroom in the skb when pushing
for the AX.25 headers resulting in this panic:

[<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50)
[<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25])
[<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss])
[<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8)
[<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914)
[<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0)
[<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48)

This patch makes mkiss behave like the 6pack driver. 6pack does not
panic.  In 6pack.c sp_setup() (same function name here) the values for
dev->hard_header_len and dev->addr_len are set to the same values as in
my mkiss patch.

[ralf@linux-mips.org: Massages original submission to conform to the usual
standards for patch submissions.]
Signed-off-by: NThomas Osterried <thomas@osterried.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the device being used to DMA map skb->data.
Erroneous device assignment causes the crash when SMMU is enabled.
This happens during TX since buffer gets DMA mapped with device
correspondign to net_device and gets unmapped using the device
related to DSAF.
Signed-off-by: NKejian Yan <yankejian@huawei.com>
Reviewed-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch incorrectly attempted nested mnt_want_write, and incorrectly
disabled nfsd's owner override for truncate.  We'll fix those problems
and make another attempt soon, for the moment I think the safest is to
revert.
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>

Pull drm fixes from Dave Airlie:
 "This should be the final set of drm fixes for 4.10: one vmwgfx boot
  fix, one vc4 fix, and a few i915 fixes:

* tag 'drm-fixes-for-v4.10-rc8' of git://people.freedesktop.org/~airlied/linux:
  drm: vc4: adapt to new behaviour of drm_crtc.c
  drm/i915: Always convert incoming exec offsets to non-canonical
  drm/i915: Remove overzealous fence warn on runtime suspend
  drm/i915/bxt: Add MST support when do DPLL calculation
  drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo
  drm/i915: fix i915 running as dom0 under Xen
  drm/i915: Flush untouched framebuffers before display on !llc
  drm/i915: fix use-after-free in page_flip_completed()
  drm/vmwgfx: Fix depth input into drm_mode_legacy_fb_format

Merge tag 'drm-intel-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes

Hopefully final fixes for v4.10, about half of them stable material.

* tag 'drm-intel-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-intel:
  drm/i915: Always convert incoming exec offsets to non-canonical
  drm/i915: Remove overzealous fence warn on runtime suspend
  drm/i915/bxt: Add MST support when do DPLL calculation
  drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo
  drm/i915: fix i915 running as dom0 under Xen
  drm/i915: Flush untouched framebuffers before display on !llc
  drm/i915: fix use-after-free in page_flip_completed()

Last-minute vc4 fix for 4.10.

* tag 'drm-misc-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-misc:
  drm: vc4: adapt to new behaviour of drm_crtc.c

USB PHYs need the MDIO clock divisor enabled earlier to work.
Initialize mdio clock divisor in probe function. The ext bus
bit available in the same register will be used by mdio mux
to enable external mdio.
Signed-off-by: NYendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver")
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function igmpv3/mld_add_delrec() we allocate pmc and put it in
idev->mc_tomb, so we should free it when we don't need it in del_delrec().
But I removed kfree(pmc) incorrectly in latest two patches. Now fix it.

Fixes: 24803f38 ("igmp: do not remove igmp souce list info when ...")
Fixes: 1666d49e ("mld: do not remove mld souce list info when ...")
Reported-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a crash when running out of grant refs when creating many
queues across many netdevs.

* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.
Signed-off-by: NRoss Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stefan Brüns says:

====================
Fixes for sierra_net driver

When trying to initiate a dual-stack (ipv4v6) connection, a MC7710, FW
version SWI9200X_03.05.24.00ap answers with an unsupported LSI. Add support
for this LSI.
Also the link_type should be ignored when going idle, otherwise the modem
is stuck in a bad link state.
Tested on MC7710, T-Mobile DE, APN internet.telekom, IPv4v6 PDP type. Both
IPv4 and IPv6 connections work.

v2: Do not overwrite protocol field in rx_fixup
v3: Remove leftover struct ethhdr *eth declaration
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the context is deactivated, the link_type is set to 0xff, which
triggers a warning message, and results in a wrong link status, as
the LSI is ignored.
Signed-off-by: NStefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a context is configured as dualstack ("IPv4v6"), the modem indicates
the context activation with a slightly different indication message.
The dual-stack indication omits the link_type (IPv4/v6) and adds
additional address fields.
IPv6 LSIs are identical to IPv4 LSIs, but have a different link type.
Signed-off-by: NStefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>