From the HID usage table when it is supported.
Tested-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Intuos5 tablets with PTH-* model numbers include a multitouch sensor
which use the same touch reports as the 3rd-generation Bamboo. No
useful information is in the HID descriptor for the touch interface
so hardcoded values are used during setup.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Reviewed-by: NChris Bagwell <chris@cnpbagwell.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The Touch Ring LEDs on Intuos5 tablets use a different report
format which supports only 4 levels of brightness. We remap
the 7-bit value obtained from sysfs to an appropriate value
for the tablet. Control of the crop mark LEDs (new to the I5)
is left for a later patch.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

We accidentally removed the check for NULL in 3aac0ef1 "Input: wacom -
isolate input registration".
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

When a tablet connect or disconnect is detected, schedule
work queue to register or unregister related input devices.

When a wireless tablet connects, it reports same USB PID
used if tablet is connected with USB cable. Use this to
update features values, set input capabilities, and then
register device.  From there, the Pen and Touch interfaces
will reuse the existing tablet's IRQ routines.

Its possible that 1 receiver is shared with 2 tablets with
different PID (small and medium Bamboo for example) so the
input is unregister at disconnect to better support this case.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The 3rd gen Bamboo Pen & Touch and Intuos5 tablets support an
optional wireless module. When its receiver is plugged into USB,
it presents 3 interfaces: 0) Monitor 1) Pen and 2) Touch.

The exact capabilities of the Pen and Touch interfaces can
not be determined until a tablet connection is established
and reported over the Monitor interface.

This patch detects this wireless receiver and enables interrupt
packets to be processed for the Monitor interface. Processing
the data in packets will be left to another patch.

Since it doesn't make sense to create an input device for the
Monitor interface, it is not created. Creation of Pen and Touch
input device is also delayed until monitor packets can be processed.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Although this better co-locates input registration logic,
the main goal is to make it easier to optionally create
input devices or delay creation to later time periods.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This calculation determines the physical dimensions of the tablet,
used later on in calculate_touch_res to obtain the touch sensor
resolution.

Instead of dividing the logical size by the resolution, the current
code performs a multiplication. This doesn't pose a problem for the
3rd-gen Bamboo since the resolution and scale factor happen to be
identical, but will produce an incorrect result for other cases.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Reviewed-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Tested-by: NChris Bagwell <chris@cnpbagwell.com>
Reviewed-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The Cintiq 24HD has three LEDs on the left side of the tablet and
three LEDs on the right side of the tablet. Switching to LED 0,
1, or 2 will enable the top, middle, or bottom LED for the respective
side. Switching to LED 3 turns off the LEDs on the respective side.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This converts the drivers in drivers/input/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.

Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.

Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Henk Vergonet <Henk.Vergonet@gmail.com>
Cc: Alessandro Rubini <rubini@ipvvis.unipv.it>
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: "Magnus Hörlin" <magnus@alefors.se>
Cc: Chris Moeller <kode54@gmail.c>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Edwin van Vliet <edwin@cheatah.nl>
Cc: Ping Cheng <pingc@wacom.com>
Cc: Eduard Hasenleithner <eduard@hasenleithner.at>
Cc: Alexander Strakh <strakh@ispras.ru>
Cc: Glenn Sommer <gsommer@datanordisk.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Override invalid pen based pktlen and x/y_max with touch
values from HID report.

Since active area of pen and touch are same on these
devices, set physical x/y size while pen x/y_max and
resolution are still valid.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Bamboo's do not declared a Digitizer-Stylus so the if() was
never executed.  wacom_features already contains correct stylus
packet length.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Only the stylus interface on Bamboo's has a feature report that can
be used to set to wacom mode.  The touch interface only has 1 report mode
and will return errors for those get/sets requests.

The get request was always erroring out because it was not marked as
an input request. Only down side of error was needlessly resending the
set request 5 times.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Reviewed-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Cintiq 21ux2 has two sets of four LEDs on right and left side of
the tablet, respectively.
Reviewed-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The LED luminance level is normally lower when no button is pressed.
Reviewed-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This commit enables control of the LEDs and OLED displays found on the
Wacom Intuos4 M, L, and XL. For this purpose, a new "wacom_led" attribute
group is added to the sysfs entry of the USB device.

This "wacom_led" group only shows up when the correct device (M, L, or XL)
is detected. The attributes are described in
 Documentation/ABI/testing/sysfs-wacom
Signed-off-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Touch devices do not report valid pressure or capacitance.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Use WAC_MSG_RETRIES define instead of a numeric constant.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Reviewed-by: NHenrik Rydberg <rydberg@euromail.se>
Reviewed-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

If we fail to retrieve HID descriptor we need to free allocated URB so
jump to proper label to do that.
Signed-off-by: NAlexander Strakh <strakh@ispras.ru>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

We need to always call usb_autopm_put_interface() in wacom_open(),
not only when initialization fails, otherwise the device will be
marked as PM-busy and will never be put in suspended state.

Based on patch by Oliver Neukum.
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

When runtime PM is enabled by default for input devices, X hangs in
wacom open:
[<ffffffff814a00ea>] mutex_lock+0x1a/0x40
[<ffffffffa02bc94b>] wacom_resume+0x3b/0x90 [wacom]
[<ffffffff81327a32>] usb_resume_interface+0xd2/0x190
[<ffffffff81327b5d>] usb_resume_both+0x6d/0x110
[<ffffffff81327c24>] usb_runtime_resume+0x24/0x40
[<ffffffff8130a2cf>] __pm_runtime_resume+0x26f/0x450
[<ffffffff8130a23a>] __pm_runtime_resume+0x1da/0x450
[<ffffffff8130a53a>] pm_runtime_resume+0x2a/0x50
[<ffffffff81328176>] usb_autopm_get_interface+0x26/0x60
[<ffffffffa02bc626>] wacom_open+0x36/0x90 [wacom]

wacom_open() takes wacom->lock and calls usb_autopm_get_interface(),
which in turn calls wacom_resume() which tries to acquire the lock
again.

The fix is to call usb_autopm_get_interface() first, before we take
the lock.

Since we do not do usb_autopm_put_interface() until wacom_close()
is called runtime PM is effectively disabled for the driver, however
changing it now would risk regressions so the complete fix will
have to wait till the next merge window.
Reported-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Bamboo P&T need to use second form of usb_set_report() to
ask to report tablet data.

With previous addition of Bamboo Touch, BTN_TOOL_TRIPLETAP is now used
for both TABLETPC2FG and BAMBOO_PT types.  So reduced check to
match type=TABLETPC2FG.

This change shows redundant check for !TABLETPC2FG in else statement.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Collect device-specific code into a single function, and use quirks to
flag specific behavior instead.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The Bamboo devices have multiple interfaces which need to be setup
separately. Use the HID parsing mechanism to achieve that.
Signed-off-by: NPing Cheng <pinglinux@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The signal-to-noise ratio varies between devices, but currently all
devices are treated the same way. Add fuzz parameters to the feature
struct, allowing for tailored treatment of devices.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

For more clearance what the functions actually do,

  usb_buffer_alloc() is renamed to usb_alloc_coherent()
  usb_buffer_free()  is renamed to usb_free_coherent()

They should only be used in code which really needs DMA coherency.

All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When Wacom devices wake up from a sleep, the switch mode command
(wacom_query_tablet_data) is needed before wacom_open is called.
wacom_query_tablet_data should not be executed inside wacom_open
since wacom_open is called more than once during probe.

wacom_retrieve_hid_descriptor is removed from wacom_resume due
to the fact that the required descriptors are stored properly
upon system resume.
Reported-and-tested-by: NAnton Anikin <Anton@Anikin.name>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Cc: stable@kernel.org
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Also get rid of wacom_le16_to_cpu() and wacom_be16_to_cpu() helpers and
ise le16_to_cpup() and be16_to_cpup() directly.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Now that we moved input device from struct wacom to struct wacom_wac,
presence of wacom_combo just complicats things for no good reason.
Let's get rid of it and simply pass URB length to wacom_wac_irq().
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Input event interface is pretty stable so let's get rig of wrappers
for input_event() and fiends and call them directly. This will simplify
and speed up code a bit.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Fix identation of switch/case statements so they follow style used by the
rest of the kernel.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

There is no reason for allocating struct wacom_wac separately from
struct wacom since both have the same lifetime rules and are not
shared. Also make 'open' field a boolean.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Touch enbaled devices share the same product ID with pen. However,
we do not want to post touch events while pen is in prox. To do so,
we used to keep a local static variable to keep track of if pen is
in prox or not. This works fine for Tablet PC devices since there
is only one device attached. With the newer touch enabled regular
tablets, we can not make this assumption any more, i.e, one system
may have more than one identical tablet plugged in.

This patch adds an new entry, shared, into the struct wacom_wac so
touch data can access pen data to locally. This solution assumes
the two tools (touch and pen) of the same ID will be probed one
after the other without interruption in between by another Wacom
device of the same ID.