Summit and Tobi expansion boards have a HDMI connector with a TFP410
encoder. Add a common include file for this configuration, and then
use it for Summit and Tobi.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Looks like quite a few omap3 boards have sharp ls037v7dw01 that's
configured as various panel dpi entries for whatever legacy reasons.
For device tree based support, let's just configure these properly for
panel ls037v7dw01 instead of panel dpi.

This patch creates a common file for panel ls037v7dw01, and makes
boards ldp and omap3-evm to use it.

The ls037v7dw01 also seems to be coupled with an ad7846 touchscreen
controller for the omaps, so let's add a basic configuration for
the touchscreen also using the default values.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch add support for lcd display on gta04 board. Display control
is connected to spi (used spi bitbang driver).
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

omap5-uevm has a single HDMI output. Add the necessary display
information, including pinmuxing.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

omap5-uevm has a tca6424a I/O expander. Add it to the .dts file.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add OMAP5 DSS nodes to omap5.dtsi.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for am43x-epos-evm's LCD panel.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for am437x-gp-evm's LCD panel.
Signed-off-by: NSathya Prakash M R <sathyap@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for the display subsystem for AM4372. The DSS on AM4372 is
basically OMAP3's DSS, without DSI and VENC blocks.
Signed-off-by: NSathya Prakash M R <sathyap@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

This patch creates a unique node for each clock in the OMAP2 power,
reset and clock manager (PRCM).
Signed-off-by: NTero Kristo <t-kristo@ti.com>

Adds pinmux and DT node for Micron (MT29F4G08AB) x8 NAND device present on
am437x-gp-evm board.
(1) As NAND Flash data lines are muxed with eMMC, Thus at a given time either
    eMMC or NAND can be enabled. Selection between eMMC and NAND is controlled:
    (a) By dynamically driving following GPIO pin from software
        SPI2_CS0(GPIO) == 0 NAND is selected (default)
        SPI2_CS0(GPIO) == 1 eMMC is selected
    (b) By statically using Jumper (J89) on the board

(2) As NAND device connnected to this board has page-size=4K and oob-size=224,
    So ROM code expects boot-loaders to be flashed in BCH16 ECC scheme for
    NAND boot.
Signed-off-by: NPekon Gupta <pekon@ti.com>
Reviewed-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixes: commit 0611c419
ARM: OMAP2+: gpmc: update gpmc_hwecc_bch_capable() for new platforms and ECC schemes

Though the commit log of above commit mentions AM43xx platforms, but code change
missed AM43xx. This patch adds AM43xx to list of those SoC which have built-in
ELM hardware engine, so that BCH ecc-schemes with hardware error-correction can
be enabled on AM43xx devices.
Reported-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Node usbhshost is supporting pinctrl, so the deprecated
quirk call can be removed.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes audio support for omap3-lilly-a83x.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add modem device tree data to Nokia N900's DTS file.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Tested-By: NIvaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add SSI device tree data for OMAP3 and Nokia N900.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Tested-By: NIvaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The current entry prevents system from idling if
the hwmod is defined in the .dts file so let's
change the idlemodes.

Note that we probably don't have SYSC_HAS_EMUFREE
or SYSS_HAS_RESET_STATUS either. If we do, those
can be added later on.
Acked-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Currently oscillator frequency is determined based on sysboot settings,
it may not be the case always. To determine it properly, efuse settings
also has to be read. CONTROL_STATUS register holds this information.
Bit 31:	if 0, frequency to be determined based on sysboot
	if 1, frequency to be determined based on efuse
Bit 29,30 - for efuse detection of frequency
Bit 22,23 - for sysboot detection of frequency

Add clock nodes (mux) to determine oscillator frequency as above.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

We need set-rate-parent flags for the display's clock path so that the
DSS driver can change the clock rate of the PLL.

This patchs adds the ti,set-rate-parent flag to disp_clk and
dpll_disp_m2_ck clock nodes.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

Add ti,set-rate-parent to dss_dss_clk so that the DSS driver can
set the rate.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

Booting Linux 3.14 on Pandaboard currently gets the following
message displayed:

smp_twd: clock not found -2

Define "mpu_periphclk" as the twd clock in omap4 dts to avoid this.
Signed-off-by: NGilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

abe_iclk's parent is aess_fclk and not abe_clk.
Also correct the parameters for clock rate calculation as used for OMAP4
since in PRCM level there's no difference between the two platform
regarding to AESS/ABE clocking.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

In OMAP5 bit 8 in PRCM registers are not defined (Reserved) unlike their
counterpart in OMAP4.
It is better to not write to these bits.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

We need "tbclk" clock data for the functioning of ehrpwm
module. Hence, populating the required clock information
in clock dts file.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

tbclk does not need to be a composite clock, we can simply
use gate clock for this purpose.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

Since commit 7adb0933 (ARM: dts: omap4: Set all audio related
IP's status to disabled as default) all audio related device are
disabled by default. Most boards were updated to enable devices
explicitly, but DuoVero was missed.

mcpdm is used for twl6040 and mcbsp1 is used for BlueTooth audio.

Cc: florian.vaussard@epfl.ch
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Conversion done by following awk script.
/0x[0-9a-f]{1,3} \(PIN/ {
	offset = sprintf("OMAP4_IOPAD(0x%03x, ", strtonum($1) + 64)
	sub(/0x[0-9a-f]{1,3} \(/, offset, $0)
	print $0
	next
}
{ print $0 }

Cc: florian.vaussard@epfl.ch
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

MTD NAND partition for file-system should start at offset=0xA00000
Signed-off-by: NPekon Gupta <pekon@ti.com>
Reviewed-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

DRA7xx platform has in-build GPMC and ELM h/w engines which can be used
for accessing externel NAND flash device. This patch:
- adds generic DT binding in dra7.dtsi for enabling GPMC and ELM h/w engines
- adds DT binding for Micron NAND Flash (MT29F2G16AADWP) present on dra7-evm
*Important*
	On DRA7 EVM, GPMC_WPN and NAND_BOOTn are controlled by DIP switch
	So following board settings are required for NAND device detection:
	SW5.9 (GPMC_WPN) = LOW
	SW5.1 (NAND_BOOTn) = HIGH
Signed-off-by: NMinal Shah <minalkshah@gmail.com>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Reviewed-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add CPSW ethernet support for AM437x GP EVM which has one slave pinned out
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add cpsw phy sel device tree node for selecting phy mode in control module
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Both the VAR-STK-OM44 and VAR-DVK-OM44 boards comes with the
WLAN/BT version of the system on module VAR-SOM-OM44.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for VAR-SOM-OM44[1] SODIMM system on module from
Variscite. SoM features a OMAP4460, 1GB RAM, Gigabit Ethernet
(LAN7500) and optional WLAN/BT.

Also add support for VAR-STK-OM44 development board from
Variscite. This kit features a VAR-SOM-OM44 and the carrier board
VAR-OM44CustomBoard[2]. The VAR-STK-OM44 is the same as
VAR-DVK-OM44 but without the LCD display.

omap4-var-stk-om44.dts replace the old and very limited
omap4-var-som.dts.

[1] http://www.variscite.com/products/system-on-module-som/cortex-a9/var-som-om44-cpu-ti-omap-4-omap4460
[2] http://www.variscite.com/products/single-board-computers/var-om44customboardSigned-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP4/5 TRMs primarily list address offsets from the padconf
physical address (which is not driver base address) and not
always the absolute physical address for padconf registers like
some other OMAP TRMs. So create a new macro to use this offset
and to avoid confusion between different OMAP parts.

For more information, see the tables in TRM for named something like
"Device Core Control Module Pad Configuration Register Fields"
and "Device Wake-Up Control Module Pad Configuration Register Fields"

Note that we now also have to update cm-t54 for the fixed up
offsets.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
[tony@atomide.com: updated comments, updated cm-t54]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Set 'ti,set-rate-parent' property for the dpll4_m5x2_mul_ck clock, which
is used for the ISP functional clock. This fixes the OMAP3 ISP driver's
clock rate configuration, which needs the rate to be propagated properly
to the divider node (dpll4_m5_ck).
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

We need to use set-rate-parent for dpll4_m5 clock path, so use the
ti,fixed-factor-clock version which supports set-rate-parent property.

The set-rate-parent flag itself is set in the following patch, this one
just changes the clock driver to ti,fixed-factor-clock without any other
changes.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

Use the ti,fixed-factor-clock version so that autoidle for
dpll_per_clkdcoldo is properly controlled after power management code
is introduced. Without this the clock may be held active even when
it is gated.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

Make sure ethernet and mdio nodes are disabled by default and enable
them explicitly only on boards that actually use them.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>