Add packet and byte counters for RX and TX paths.

$ ifconfig eth1
eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet6 fe80::5054:ff:fe12:3501  prefixlen 64  scopeid 0x20<link>
        ether 52:54:00:12:35:01  txqueuelen 1000  (Ethernet)
        RX packets 63  bytes 15813 (15.4 KiB)
        RX errors 1  dropped 0  overruns 0  frame 0
        TX packets 79  bytes 17991 (17.5 KiB)
        TX errors 7  dropped 0 overruns 0  carrier 0  collisions 0

Rx / Tx errors tested by injecting faults in qemu's hardware model for Rocker.

v2:
- moved counter locations to avoid potential use after free per Florian's comment
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Cc: Scott Feldman <sfeldma@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPSW never uses RX_THRESHOLD or MISC interrupts. In
fact, they are always kept masked in their appropriate
IRQ Enable register.

Instead of allocating an IRQ that never fires, it's best
to remove that code altogether and let future patches
implement it if anybody needs those.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is in preparation for a nicer IRQ
handling scheme where we use different IRQ
handlers for each IRQ line (as it should be).

Later, we will also drop IRQs offset 0 and 3
because they are always disabled in this driver.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.

This makes the very common pattern of

  if (genlmsg_end(...) < 0) { ... }

be a whole bunch of dead code. Many places also simply do

  return nlmsg_end(...);

and the caller is expected to deal with it.

This also commonly (at least for me) causes errors, because it is very
common to write

  if (my_function(...))
    /* error condition */

and if my_function() does "return nlmsg_end()" this is of course wrong.

Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.

Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did

-	return nlmsg_end(...);
+	nlmsg_end(...);
+	return 0;

I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.

One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix some spelling mistakes, coding style and don't assign value to static var.
Signed-off-by: NAkash Shende <akash0x53s@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 07f6c4bc (tipc: convert tipc reference table to use generic
rhashtable) introduced a problem with port listing in the new netlink
API. It broke the resume functionality resulting in a never ending
loop. This was caused by starting with the first hash table every time
subsequently never returning an empty skb (terminating).

This patch fixes the resume mechanism by keeping a logical reference
to the last hash table along with a logical reference to the socket
(port) that didn't fit in the previous message.
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2015-01-16

Here are some more bluetooth & ieee802154 patches intended for 3.20:

 - Refactoring & cleanups of ieee802154 & 6lowpan code
 - Various fixes to the btmrvl driver
 - Fixes for Bluetooth Low Energy Privacy feature handling
 - Added build-time sanity checks for sockaddr sizes
 - Fixes for Security Manager registration on LE-only controllers
 - Refactoring of broken inquiry mode handling to a generic quirk

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch benefits from newly introduced switchdev notifier and uses it
to propagate fdb learn events from rocker driver to bridge. That avoids
direct function calls and possible use by other listeners (ovs).
Suggested-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces new notifier for purposes of exposing events which happen
on switch driver side. The consumers of the event messages are mainly involved
masters, namely bridge and ovs.
Suggested-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After a "page = alloc_page(mask);", we do not need to use
compound_head() : page already points to the right place.

This would be true even if using alloc_pages().
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This field already contains the length of the iovec, no need to calculate it
again.
Suggested-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
s390: network patches for net-next

here are some s390 related patches for net-next
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The member irq_tasklet in the qeth_channel structure
is not referenced anymore and is removed from the
structure.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace combination of strsep() and a temporary char *
followed by a series of "if (!strcmp(...))" with a series
of "if (sysfs_streq(...))".
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reviewed-by: NThomas-Mich Richter <tmricht@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qeth_card_hw_is_reachable() was introduced as part of a new
functionality, but it is a useful abstraction that can replace
verbose checks througout the rest of the `qeth` driver.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reviewed-by: NThomas-Mich Richter <tmricht@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function debug_unregister() tests whether its argument is
NULL and then returns immediately. Thus the test around the call
is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is concerned with migrating the time variables for the s390
network drivers. The changes handle the y2038 problem where timespec will
overflow in the year 2038. timespec was replaced by unsigned long and
all time variables get their values from the jiffies global variable.
This was done for the sake of speed and efficiency.
Signed-off-by: NAya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was suggested by DaveM to change the name as "len" might indicate
unit bytes.
Suggested-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This action provides a possibility to exec custom BPF code.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

problems with bridge getlink/setlink notifications today:
        - bridge setlink generates two notifications to userspace
                - one from the bridge driver
                - one from rtnetlink.c (rtnl_bridge_notify)
        - dellink generates one notification from rtnetlink.c. Which
	means bridge setlink and dellink notifications are not
	consistent

        - Looking at the code it appears,
	If both BRIDGE_FLAGS_MASTER and BRIDGE_FLAGS_SELF were set,
        the size calculation in rtnl_bridge_notify can be wrong.
        Example: if you set both BRIDGE_FLAGS_MASTER and BRIDGE_FLAGS_SELF
        in a setlink request to rocker dev, rtnl_bridge_notify will
	allocate skb for one set of bridge attributes, but,
	both the bridge driver and rocker dev will try to add
	attributes resulting in twice the number of attributes
	being added to the skb.  (rocker dev calls ndo_dflt_bridge_getlink)

There are multiple options:
1) Generate one notification including all attributes from master and self:
   But, I don't think it will work, because both master and self may use
   the same attributes/policy. Cannot pack the same set of attributes in a
   single notification from both master and slave (duplicate attributes).

2) Generate one notification from master and the other notification from
   self (This seems to be ideal):
     For master: the master driver will send notification (bridge in this
	example)
     For self: the self driver will send notification (rocker in the above
	example. It can use helpers from rtnetlink.c to do so. Like the
	ndo_dflt_bridge_getlink api).

This patch implements 2) (leaving the 'rtnl_bridge_notify' around to be used
with 'self').

v1->v2 :
	- rtnl_bridge_notify is now called only for self,
	so, remove 'BRIDGE_FLAGS_SELF' check and cleanup a few things
	- rtnl_bridge_dellink used to always send a RTM_NEWLINK msg
	earlier. So, I have changed the notification from br_dellink to
	go as RTM_NEWLINK
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-01-16

This series contains updates to i40e and i40evf.

This series is a little bit larger than normal because two of the patches are
version bumps.

Shannon provides tweaks to i40e and i40evf to keep the firmware, software
and silicon validation in line together by removing unused and
deprecated code, adding define for iSCSI and fix queue mask size.  Fix
i40e so we do not give up in the reset/rebuild process if DCB setup
fails, just handle it the same as in the probe setup.  Cleans up PTP
log messages by removing the use of __func__ as we are not using that
any longer and removes the netdev name, since that can change and can
be misleading.  Adds struct size checks to indirect and command
structs that were left out previously.  Added admin queue API updates
(LLDP control, OEM OCSD and OCBB commands).

Kevin increases ASQ timeout for scenarios with multi-function devices.

Carolyn fixes a problem where the interrupts descriptions from the MSIx
configuration were truncating the needed bus info, which makes it hard
to distinguish configurations from port to port.  Increased the string
buffer size in order to allow the full data to be displayed.

Sravanthi cleans up the dump stats string from debugfs.

Jacob updates i40e to only enable the PTP interrupt in PFs which have PTP
enabled, instead of blindly enabling the PTP interrupt flags for all PFs.
Also updated i40e so that we do not do Tx or Rx timestamps if we do not
have PTP enabled.  Added the same check against pf->ptp_rx as we have
in Rx timestamp code path because it is possible that the user can
configure only Tx hardware timestamping so we do not want to check for
Rx timestamp hang since the software won't be handling them.

Neerav updates the driver to disable firmware LLDP agent for NICs with
a firmware version lower than v4.3 and added a message when this happens.
Adds parsing and reporting of iSCSI capability for a given device or
function, as well as adding support for iSCSI partition type with DCB
in NPAR mode.

v2:
 - Dropped patch 10 "i40e: clean up PTP log messages" based on feedback
   from David Laight and David Miller
 - Split up the original patch 13 "i40e: AQ API updates for new commands"
   into 2 patches (now #12 & #13) based on feedback from Or Gerlitz
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver updates 2015-01-16

The following series of patches includes functional updates to the
driver as well as some trivial changes.

- Fix checks/warnings from checkpatch in the amd-xgbe driver
- Fix checks/warnings from checkpatch in the amd-xgbe-phy driver
- Add a check to be sure that the amd-xgbe driver is using the
  amd-xgbe-phy driver
- Use a saved control register value when bringing the PCS out of
  suspend
- Clear all device state during a device restart
- Simplify the Rx descriptor ring tracking
- Remove the need for Tx path spinlocks
- Update the auto-negotiation logic to make use of the auto-negotiation
  interrupt
- Properly support/advertise the FEC capability of the device
- Use the proper page registers during auto-negotiation extended next
  page exchange
- Add ACPI support to the amd-xgbe and amd-xgbe-phy drivers
- Allow platform specific phy settings to be supplied by UEFI

This patch series is based on net-next.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Certain PHY settings need to be configurable by UEFI depending on the
platform being used.  Add new device tree / ACPI properties that, if
present, will override the pre-determined values currently used.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for ACPI to the amd-xgbe and amd-xgbe-phy drivers. This
support converts many of the device tree APIs to the new device_property
APIs.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When receiving and processing extended next pages the base registers
were used instead of the XNP registers. Update the code to use the
device XNP and link partner XNP registers.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Advertise and apply the Forward Error Correction capabilities of the
device based on the FEC ability of the device. Also, remove the use
of some hard coded values related to KR and FEC in preference of some
#defines.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The auto negotiation logic was geared to being the initiator of the
auto negotiation. This presented problems when auto negotiation was
initiated by the remote end. Change the auto negotiation logic to
make use of the auto negotiation event interrupt thus allowing the
auto negotiation state machine to function properly in either scenario.
This also removes the polling during auto-negotiation.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the Tx ring cleanup can run at the same time that data is being
transmitted, a spin lock was used to protect the ring. This patch
eliminates the need for Tx spinlocks by updating the current ring
position only after all ownership bits for data being transmitted have
been set. This will insure that ring operations in the Tx cleanup path
do not interfere with the ring operations in the Tx transmit path.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the Rx descriptor ring processing similar to the Tx descriptor
ring processing.  Remove the realloc_index and realloc_threshold
variables and base everything on the current index counter and the
dirty index counter.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When performing a device restart, like during an MTU change, sometimes
the device queues still have data and get hung up trying to flush
resulting in the device becoming unresponsive until brought down and
back up. To prevent this, always perform a device reset during a
restart.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reads to registers are undefined when the PCS is powered down. To be
safe, save the CTRL1 register used for power down during suspend and
restore that value during resume.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The amd-xgbe driver relies on the amd-xgbe-phy phylib driver. Add a
check to be sure that if any errors occur during probing of the
amd-xgbe-phy driver then the amd-xgbe driver returns an error.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This set of patches resolves some checks reported by the checkpatch
tool.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This set of patches resolves some checks reported by the checkpatch
tool.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump i40e to 1.2.6 and i40evf to 1.2.0 version.

Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add parsing and reporting of iSCSI capability for a given device or
function.

Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.

Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.

Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of leaving the Rx timestamps in the same mode as before if we
disable the Rx logic, we can set it into a mode that has the fewest
possible timestamps generated. To do this, select only V1 mode, but do
not enable UDP packet recognition. This should eliminate all (or at
least almost all) Rx timestamps, since V1 packets are always over UDP.

Change-ID: If847288e0030a716e059c4c33ab114f2cf038f05
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It's possible that the user configured only Tx hardware timestamping,
and thus we might be receiving PTP traffic which we timestamp but which
software never reads. In this case we don't want to check for Rx
timestamp hang, because we already know that software won't be handling
them. Thus, we add the same check against pf->ptp_rx as we have in the
Rx timestamp code path.

Change-ID: I66486c8dba307facbff8eace4e52e2f083789d1b
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add lldp control commands, add oem ocsd and ocbb commands.

Change-ID: I89eba2bd02013d0a44e1ce900559c54bb15f4a66
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>