- 22 9月, 2012 1 次提交
-
-
由 AnilKumar Ch 提交于
Modify c_can device names from *_CAN_DEVTYPE to BOSCH_*_CAN to make use of same names for array indexes in c_can_id_table[] as well as device names. This patch also add indexes to c_can_id_table array. Signed-off-by: NAnilKumar Ch <anilkumar@ti.com> Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
-
- 31 7月, 2012 1 次提交
-
-
由 Viresh Kumar 提交于
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h, there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif macros. Signed-off-by: NViresh Kumar <viresh.kumar@st.com> Acked-by: NDavid S. Miller <davem@davemloft.net> Cc: Bhupesh Sharma <bhupesh.sharma@st.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Mike Turquette <mturquette@linaro.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: viresh kumar <viresh.linux@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 07 6月, 2012 2 次提交
-
-
由 AnilKumar Ch 提交于
This patch adds the support for D_CAN controller driver to the existing C_CAN driver. Bosch D_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ ipmodules_1/can/d_can_users_manual_111.pdf A new array is added for accessing the d_can registers, according to d_can controller register space. Current D_CAN implementation has following limitations, this is done to avoid large changes to the C_CAN driver. 1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP supports upto 32 message objects but in case of D_CAN we can configure upto 128 message objects. 2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers. 3. These patches have been tested on little endian machine, there might be some hidden endian-related issues due to the nature of the accesses (32-bit registers accessed as 2 16-bit registers). However, I do not have a big-endian D_CAN implementation to confirm. Signed-off-by: NAnilKumar Ch <anilkumar@ti.com> Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
-
由 AnilKumar Ch 提交于
c_can uses overlay structure for accessing c_can module registers. With this kind of implementation it is difficult to add one more ip which is similar to c_can in functionality but different register offsets. This patch changes the overlay structure implementation to an array with register offset as index. This way we can overcome the above limitation. Signed-off-by: NAnilKumar Ch <anilkumar@ti.com> Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
-
- 29 11月, 2011 1 次提交
-
-
由 Axel Lin 提交于
This patch converts the drivers in drivers/net/can/* to use the module_platform_driver() macro which makes the code smaller and a bit simpler. Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Bhupesh Sharma <bhupesh.sharma@st.com> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Anatolij Gustschin <agust@denx.de> Cc: Paul Bolle <pebolle@tiscali.nl> Cc: Kurt Van Dijck <kurt.van.dijck@eia.be> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NAxel Lin <axel.lin@gmail.com> Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 7月, 2011 1 次提交
-
-
由 Huang Weiyi 提交于
Remove duplicated #include('s) in drivers/net/can/c_can/c_can.c drivers/net/can/c_can/c_can_platform.c Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 6月, 2011 1 次提交
-
-
由 Jesper Juhl 提交于
It was pointed out by 'make versioncheck' that some includes of linux/version.h are not needed in drivers/net/. This patch removes them. Signed-off-by: NJesper Juhl <jj@chaosbits.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 6月, 2011 1 次提交
-
-
由 Vitaliy Ivanov 提交于
Many stupid corrections of duplicated includes based on the output of scripts/checkincludes.pl. Signed-off-by: NVitaliy Ivanov <vitalivanov@gmail.com> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 28 3月, 2011 1 次提交
-
-
由 Marc Kleine-Budde 提交于
This patch fixes the check in the probe function whether a IRQ was supplied to the driver. The original driver check the irq "struct resource *" against <= 0. Use "platform_get_irq" instead. Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de> Cc: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 2月, 2011 1 次提交
-
-
由 Bhupesh Sharma 提交于
Bosch C_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf This patch adds the support for this controller. The following are the design choices made while writing the controller driver: 1. Interface Register set IF1 has be used only in the current design. 2. Out of the 32 Message objects available, 16 are kept aside for RX purposes and the rest for TX purposes. 3. NAPI implementation is such that both the TX and RX paths function in polling mode. Signed-off-by: NBhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-