Convert the last instances of strncpy() to the preferred strlcpy().
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Internal stress testing with jumbo frames shows the reliability of ICH9 and
ICH10D devices is improved in certain corner cases by disabling the Early
Receive feature. To reduce the performance impact caused by disabling this
feature, the packet buffer sizes and relevant flow control settings are
modified accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This code snippet is simply writing default values to the register which is
unnecessary since the values are programmed into the register by default.
There is a special case for 80003es2lan needing the Retransmit on Late
Collision bit set but that is also done in e1000_init_hw_80003es2lan().
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the default hardware values for TIPG except for 80003es2lan(*).  The
code that is removed in this patch is either unnecessarily writing the TIPG
register with the hardware default values for some devices (82571/2/3/4) or
writing the wrong value for others (ICH/PCH LOMs).  The only change in
functionality is setting the correct default TIPG for the latter devices.

(*) The correct value for 80003es2lan is already set properly in
e1000_init_hw_80003es2lan() and e1000_cfg_kmrn_{10_100|1000}_80003es2lan(),
and the unused flag FLAG_TIPG_MEDIUM_FOR_80003ESLAN is removed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware erratum workaround where the TXDCTL register must be the same
setting for both queues should always be done.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For ring-specific functions, pass a pointer to the ring struct instead of a
pointer to the adapter struct.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations.  Also, change current u8 __iomem pointers
to void __iomem pointers.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable RPS by default.  Disallow jumbo frames when both receive checksum
and receive hashing are enabled because the hardware cannot do both IP
payload checksum (enabled when receive checksum is enabled when using
packet split which is used for jumbo frames) and provide RSS hash at the
same time.

v2: added ethtool command to query flow hashing behavior per Ben Hutchings
    and changed the type of rsskey to cleanup the setting of the register
    array and avoid unnecessary casts (as pointed out by Joe Perches).
    The long error messages are not changed since there is nothing in
    the kernel ./Documentation that suggests the preferred method for
    dealing with long messages other than to never break strings; leaving
    them as-is for now.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

1) cleanup whitespace in e1000_rx_checksum() function header comment
2) do not check hardware checksum when Rx checksum is disabled
3) reduce duplicated calls to le16_to_cpu() by just using it within
   e1000_rx_checksum() instead of in each call to the function

v2: use swab16 instead of le16_to_cpu & htons and corrected type for the
passed-in csum
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

DaveM said:
   Please, this kind of stuff rots forever and not using bool properly
   drives me crazy.

Joe Perches <joe@perches.com> gave me the spatch script:

	@@
	bool b;
	@@
	-b = 0
	+b = false
	@@
	bool b;
	@@
	-b = 1
	+b = true

I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let caller know the result of adding/removing vlan id to/from vlan
filter.

In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on a patch from Mike McElroy created against the out-of-tree e1000e
driver:

Hitting the BUG_ON in napi_enable(). Code inspection shows that this can
only be triggered by calling napi_enable() twice without an intervening
napi_disable().

I saw the following sequence of events in the stack trace:

1) We simulated a cable pull using an Extreme switch.
2) e1000_tx_timeout() was entered.
3) e1000_reset_task() was called. Saw the message from e_err() in the
console log.
4) e1000_reinit_locked was called. This function calls e1000_down() and
e1000_up(). These functions call napi_disable() and napi_enable()
respectively.
5) Then on another thread, a monitor task saw carrier was down and executed
'ip set link down' and 'ip set link up' commands.
6) Saw the '_E1000_RESETTING'warning fron the e1000_close function.
7) Either the e1000_open() executed between the e1000_down() and e1000_up()
calls in step 4 or the e1000_open() call executed after the e1000_up()
call.  In either case, napi_enable() is called twice which triggers the
BUG_ON.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Mike McElroy <mike.mcelroy@stratus.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on the original patch submitted my Michael Wang
<wangyun@linux.vnet.ibm.com>.
Descriptors may not be write-back while checking TX hang with flag
FLAG2_DMA_BURST on.
So when we detect hang, we just flush the descriptor and detect
again for once.

-v2 change 1 to true and 0 to false and remove extra ()

CC: Michael Wang <wangyun@linux.vnet.ibm.com>
CC: Flavio Leitner <fbl@redhat.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Changes to e1000e to use byte queue limits.
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

v2:	add couple missing conversions in drivers
	split unexporting netdev_fix_features()
	implemented %pNF
	convert sock::sk_route_(no?)caps
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on the original patch from Joe Perches.
Use the current logging styles.
pr_<level> conversions are now prefixed with "e1000e:"
Correct a couple of defects where the trailing NTU may have
been printed on a separate line because of an interleaving
hex_dump.
Remove unnecessary uses of KERN_CONT and use single pr_info()s
to avoid any possible output interleaving from other modules.
Coalesce formats as appropriate.
Remove an extra space from a broken across lines
coalescing of "Link Status " and " Change".

-v2 Remove changes to Copyright string

CC: Joe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

Commit afc4b13d (net: remove use of ndo_set_multicast_list in
drivers) changed e1000e to use the ndo_set_rx_mode entry point,
but didn't implement the unicast address programming
functionality. Implement it to achieve the ability to add unicast
addresses.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.

Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

e1000e allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Private rx_csum flags are now duplicate of netdev->features &
NETIF_F_RXCSUM.  Remove those duplicates and use the net_device_ops
ndo_set_features.  This is based on the original patch submitted by
Michał Mirosław <mirq-linux@rere.qmqm.pl>

Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some features currently not supported by the driver (e.g. RSS) require the
use of extended descriptors, but the driver is setup to only use legacy
descriptors in all modes except for when jumbo frames are enabled on some
parts.  Convert the driver to always use extended descriptors in order to
enable the forthcoming support of these other features.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The recent commit a6b7a407 when back-ported to the out-of-tree e1000e
driver caused a compilation error on older kernels which required a
re-ordering of the #include files.  This cosmetic patch syncs the two
drivers for easier maintainability.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In process and sleep allowed context, favor GFP_KERNEL allocations over
GFP_ATOMIC ones.

-v2: fixed checkpatch.pl warnings

CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ben Greear <greearb@candelatech.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Doing a PHY page select can take a long time, relatively speaking. This
can cause a significant delay when updating a number of PHY registers on
the same page by unnecessarily setting the page for each PHY access. For
example when going to Sx, all the PHY wakeup registers (WUC, RAR[], MTA[],
SHRAR[], IP4AT[], IP6AT[], etc.) on 82577/8/9 need to be updated which
takes a long time which can cause issues when suspending.

This patch introduces new PHY ops function pointers to allow callers to
set the page directly and do any number of PHY accesses on that page.
This feature is currently only implemented for 82577, 82578 and 82579
PHYs for both the normally addressed registers as well as the special-
case addressing of the PHY wakeup registers on page 800. For the latter
registers, the existing function for accessing the wakeup registers has
been divided up into three- 1) enable access to the wakeup register page,
2) perform the register access and 3) disable access to the wakeup register
page. The two functions that enable/disable access to the wakeup register
page are necessarily available to the caller so that the caller can restore
the value of the Port Control (a.k.a. Wakeup Enable) register after the
wakeup register accesses are done.

All instances of writing to multiple PHY registers on the same page are
updated to use this new method and to acquire any PHY locking mechanism
before setting the page and performing the register accesses, and release
the locking mechanism afterward.

Some affiliated magic number cleanup is done as well.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Start the Tx queue when the interface is brought up in e1000e_up() but do
not schedule the queue until link is up as detected in the watchdog task
which sets netif_carrier_on.

Also flush the descriptors and clean the Tx and Rx rings before resetting
the hardware when bringing the interface down otherwise there is a small
window where the watchdog task can be triggered with netif_carrier_off
and the Tx ring not yet empty which causes an additional and unnecessary
reset.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When repeatedly cycling Sx->S0 states with the network cable unplugged,
the 82579 PHY may not initialize as expected and may require a full power
cycle to recover functionality to the device.  Workaround this by testing
access of the PHY registers after resuming; if that returns unexpected
results toggle the LANPHYPC signal to power cycle the PHY.

This is implemented in the new function e1000_resume_workarounds_pchlan()
which calls another new function, e1000_toggle_lanphypc_value_ich8lan(),
which has been created to reduce code duplication (same functionality
required by a previous workaround).  Also, e1000e_disable_gig_wol_ich8lan
is now e1000_suspend_workarounds_ich8lan to better reflect what it does.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout.  Give
them an explicit include via the following $0.02 script.

 =========================================
 #!/bin/bash
 MANUAL=""
 for i in `git grep -l 'prefetch(.*)' .` ; do
 	grep -q '<linux/prefetch.h>' $i
 	if [ $? = 0 ] ; then
 		continue
 	fi

 	(	echo '?^#include <linux/?a'
 		echo '#include <linux/prefetch.h>'
 		echo .
 		echo w
 		echo q
 	) | ed -s $i > /dev/null 2>&1
 	if [ $? != 0 ]; then
 		echo $i needs manual fixup
 		MANUAL="$i $MANUAL"
 	fi
 done
 echo ------------------- 8\<----------------------
 echo vi $MANUAL
 =========================================
Signed-off-by: NPaul <paul.gortmaker@windriver.com>
[ Fixed up some incorrect #include placements, and added some
  non-network drivers and the fib_trie.c case    - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout.  Give
them an explicit include via the following $0.02 script.

 =========================================
 #!/bin/bash
 MANUAL=""
 for i in `git grep -l 'prefetch(.*)' .` ; do
 	grep -q '<linux/prefetch.h>' $i
 	if [ $? = 0 ] ; then
 		continue
 	fi

 	(	echo '?^#include <linux/?a'
 		echo '#include <linux/prefetch.h>'
 		echo .
 		echo w
 		echo q
 	) | ed -s $i > /dev/null 2>&1
 	if [ $? != 0 ]; then
 		echo $i needs manual fixup
 		MANUAL="$i $MANUAL"
 	fi
 done
 echo ------------------- 8\<----------------------
 echo vi $MANUAL
 =========================================
Signed-off-by: NPaul <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to use it in _e1000e_disable_aspm.  This routine is used for error
recovery, where the pci_bus_sem is already held, and we don't want
pci_disable_link_state to try to take it again.  So add a locked variant
for use in cases like this.

Found lock up:

[ 2374.654557] kworker/32:1    D ffff881027f6b0f0     0  6075      2 0x00000000
[ 2374.654816]  ffff88503f099a68 0000000000000046 ffff88503f098000 0000000000004000
[ 2374.654837]  00000000001d1ec0 ffff88503f099fd8 00000000001d1ec0 ffff88503f099fd8
[ 2374.654860]  0000000000004000 00000000001d1ec0 ffff88503dcc8000 ffff88503f090000
[ 2374.654880] Call Trace:
[ 2374.654898]  [<ffffffff810b1302>] ? __lock_acquired+0x3a/0x224
[ 2374.654914]  [<ffffffff81c2b59c>] ? _raw_spin_unlock_irq+0x30/0x36
[ 2374.654925]  [<ffffffff810b069d>] ? trace_hardirqs_on_caller+0x1f/0x178
[ 2374.654936]  [<ffffffff81c2ab24>] rwsem_down_failed_common+0xd3/0x103
[ 2374.654945]  [<ffffffff810b158f>] ? __lock_contended+0x3a/0x2a2
[ 2374.654955]  [<ffffffff81c2ab7b>] rwsem_down_read_failed+0x12/0x14
[ 2374.654967]  [<ffffffff813371e4>] call_rwsem_down_read_failed+0x14/0x30
[ 2374.654981]  [<ffffffff8135df20>] ? pci_disable_link_state+0x5f/0xf5
[ 2374.654990]  [<ffffffff81c2a0e6>] ? down_read+0x7e/0x91
[ 2374.654999]  [<ffffffff8135df20>] ? pci_disable_link_state+0x5f/0xf5
[ 2374.655008]  [<ffffffff8135df20>] pci_disable_link_state+0x5f/0xf5
[ 2374.655024]  [<ffffffff81661796>] e1000e_disable_aspm+0x55/0x5a
[ 2374.655037]  [<ffffffff816677eb>] e1000_io_slot_reset+0x59/0xea
[ 2374.655048]  [<ffffffff8135fe0d>] ? report_mmio_enabled+0x5d/0x5d
[ 2374.655057]  [<ffffffff8135fe3b>] report_slot_reset+0x2e/0x5d
[ 2374.655072]  [<ffffffff8135369e>] pci_walk_bus+0x8a/0xb7
[ 2374.655081]  [<ffffffff8135fe0d>] ? report_mmio_enabled+0x5d/0x5d
[ 2374.655091]  [<ffffffff813603be>] broadcast_error_message+0xa4/0xb2
[ 2374.655101]  [<ffffffff81352c71>] ? pci_bus_read_config_dword+0x72/0x80
[ 2374.655110]  [<ffffffff813606df>] do_recovery+0x9e/0xf9
[ 2374.655120]  [<ffffffff81360786>] handle_error_source+0x4c/0x51
[ 2374.655129]  [<ffffffff81360974>] aer_isr_one_error+0x1e9/0x21a
[ 2374.655138]  [<ffffffff81360a6c>] aer_isr+0xc7/0xcc
[ 2374.655147]  [<ffffffff813609a5>] ? aer_isr_one_error+0x21a/0x21a
[ 2374.655159]  [<ffffffff81096d9f>] process_one_work+0x237/0x3ec
[ 2374.655168]  [<ffffffff81096d10>] ? process_one_work+0x1a8/0x3ec
[ 2374.655178]  [<ffffffff8109728d>] worker_thread+0x17c/0x240
[ 2374.655186]  [<ffffffff810b0803>] ? trace_hardirqs_on+0xd/0xf
[ 2374.655196]  [<ffffffff81097111>] ? manage_workers+0xab/0xab
[ 2374.655209]  [<ffffffff8109c8ed>] kthread+0xa0/0xa8
[ 2374.655223]  [<ffffffff81c332d4>] kernel_thread_helper+0x4/0x10
[ 2374.655232]  [<ffffffff81c2b880>] ? retint_restore_args+0xe/0xe
[ 2374.655243]  [<ffffffff8109c84d>] ? __init_kthread_worker+0x5b/0x5b
[ 2374.655252]  [<ffffffff81c332d0>] ? gs_change+0xb/0xb

when aer happens,
pci_walk_bus already have down_read(&pci_bus_sem)...
then report_slot_reset
        ==> e1000_io_slot_reset
                ==> e1000e_disable_aspm
                        ==> pci_disable_link_state...

We can not use pci_disable_link_state, and it will try to hold pci_bus_sem again.

Try to have __pci_disable_link_state that will not need to hold pci_bus_sem.

-v2: change name to pci_disable_link_state_locked() according to Jesse.

[jbarnes: make sure new function is exported for modules]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Based on a patch from Stephen Hemminger <shemminger@vyatta.com>.

The new ethtool set_phys_id takes over controlling the LED for
identifying boards.  This fixes the lockout during that period.
For this device lots of extra infrastructure can also be removed by
using set_phys_id.

v2: - return blink frequency for parts that do not support blink in h/w
    - add blink_led function pointers for devices that do support blink
      in h/w to cleanup the test for this functionality
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a patch from Naga Chumbalkar <nagananda.chumbalkar@hp.com>:

If ASPM L0s needs to be disabled due to HW errata, do it prior to
"enabling" the device. This way if the kernel ever defaults its
aspm_policy to POLICY_POWERSAVE, then the e1000e driver will get a
chance to disable ASPM on the misbehaving device *prior* to calling
pci_enable_device_mem(). This will be useful in situations
where the BIOS indicates ASPM support on the server by clearing the
ACPI FADT "ASPM Controls" bit.

Note:
The kernel (2.6.38) currently uses the BIOS "default" as its aspm_policy.
However, Linux distros can diverge from that and set the default to
"powersave".

v2: o cleanup namespace pollution of e1000e_disable_aspm(),
    o fix type and initialization of the new aspm_disable_flag in a few
      functions, and
    o redefine FLAG2_DISABLE_ASPM_L0S to the first unused bit in
      adapter->flags2.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Just move the unlock down a bit because it unlocks too
early leaving a chance for get_stats64() run in parallel
while it is still accessing the stats.
Signed-off-by: NFlavio Leitner <fleitner@redhat.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This switches the e1000e driver to use the new VLAN interfaces.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>