The pvrusb2 driver's sysfs implementation had long since implemented a
dummy hotplug function because at the time the kernel would oops
without at least the empty function being present.  Today - after
numerous class interface changes in the kernel - this pvrusb2 change
had been dutifully carried forward but an inspection of the kernel
sources shows that it is no longer needed.  So remove the dummy
function and its reference.  This also solves a recurring backwards
compatibility issue in the pvrusb2 driver as the class interface has
been getting thrashed in the kernel.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

if(!x & y) should either be if(!(x & y)) or if(!x && y)
    I made changes as seemed appropriate, but please review
    this is against current git.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fixes the signal strength value (higher value = higher signal strength)
and scales the value to the range of 0..ffff. The characteristic itself
is wrong. To get proper values on a TT-C2300 in the range of 40..60%
real signal strength, the values from the patch should be divide by two.
The attached patch doesn't fix the characteristic.
Signed-off-by: NHartmut Birr <e9hack@googlemail.com>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix reported signal strength value (higher value = higher signal strength).
Signed-off-by: NHartmut Birr <e9hack@googlemail.com>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Bit error counting fixed for the tda10021.
Signed-off-by: NHartmut Birr <e9hack@googlemail.com>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Change the acquisition range for clock recovery from 120 ppm to
240ppm. Apparently, some cable providers in Germany are playing with
their parameters, and the capture range of the ves1820 is too small
to acquire a lock with the current setting... ;-(
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Two fixes for the 'saa7146_wait_for_debi_done' code:
(a) Timeout did not work when the routine was called with
    interrupts disabled.
(b) Reduce PCI I/O load caused by saa7146_wait_for_debi_done.
    Seems to be very important on fast machines!

Based on code posted by Hartmut Birr @vdr-portal.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

All of these drivers select VIDEO_IR, which uses the input subsystem,
so they should also depend on INPUT.

Problem examples:

drivers/built-in.o: In function `ir_input_key_event':
ir-functions.c:(.text+0x10849a): undefined reference to `input_event'
ir-functions.c:(.text+0x1084ac): undefined reference to `input_event'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11cc0a): undefined reference to `get_key_pinnacle_color'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11cc4f): undefined reference to `get_key_pinnacle_grey'
drivers/built-in.o: In function `saa7134_input_fini':
(.text+0x11cd8b): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d1fa): undefined reference to `input_allocate_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d317): undefined reference to `input_register_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d6ca): undefined reference to `input_free_device'

drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c3f3): undefined reference to `ir_codes_hauppauge_new'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c450): undefined reference to `ir_codes_pinnacle_color'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c480): undefined reference to `ir_codes_purpletv'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c495): undefined reference to `ir_codes_pinnacle_grey'
drivers/built-in.o: In function `saa7134_ir_start':
(.text+0x11c622): undefined reference to `ir_rc5_timer_end'
drivers/built-in.o: In function `saa7134_ir_start':
(.text+0x11c637): undefined reference to `ir_rc5_timer_keyup'
drivers/built-in.o: In function `build_key':
saa7134-input.c:(.text+0x11c769): undefined reference to `ir_extract_bits'
saa7134-input.c:(.text+0x11c7ad): undefined reference to `ir_input_keydown'
saa7134-input.c:(.text+0x11c7f0): undefined reference to `ir_input_keydown'
saa7134-input.c:(.text+0x11c7f9): undefined reference to `ir_input_nokey'
saa7134-input.c:(.text+0x11c806): undefined reference to `ir_input_nokey'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ca07): undefined reference to `ir_codes_encore_enltv'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11caf6): undefined reference to `ir_input_init'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cbf2): undefined reference to `ir_codes_avermedia'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc24): undefined reference to `ir_codes_pctv_sedna'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc53): undefined reference to `ir_codes_flydvb'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc85): undefined reference to `ir_codes_videomate_tv_pvr'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ccb7): undefined reference to `ir_codes_pixelview'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cce9): undefined reference to `ir_codes_eztv'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cd1b): undefined reference to `ir_codes_manli'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cda8): undefined reference to `ir_codes_cinergy'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cdd7): undefined reference to `ir_codes_flyvideo'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ce06): undefined reference to `ir_codes_asus_pc39'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ce7d): undefined reference to `ir_codes_gotview7135'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cee1): undefined reference to `ir_codes_proteus_2309'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Media ir-functions uses input_(*) functions so it should depend
on the INPUT config symbol.

drivers/built-in.o: In function `ir_input_key_event':
ir-functions.c:(.text+0x10849a): undefined reference to `input_event'
ir-functions.c:(.text+0x1084ac): undefined reference to `input_event'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch fixes CONFIG_TUNER_TEA5761=m broken by
commit ca805d57.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

irq handlers have returned a return value for years now... catch up with
the times.

Also, ditch unneeded prototype.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

saa7134: fix analog audio in on medion md8800 quadro, aka CTX944
Signed-off-by: NHermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Semicolon fix.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch enables QAM Annex-B support (US digital cable)
for the s5h1409 VSB/QAM demodulator.

Tested successfully with the mt2131 tuner,
present on the following supported boards:

Hauppauge WinTV-HVR-1250
Hauppauge WinTV-HVR-1800
Hauppauge WinTV-HVR-1800lp

This patch is also known to work with an upcoming XC5000 tuner driver.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add a pointer to the (recently posted) Cafe data sheet.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If the system is suspended while the camera is streaming, it will not
continue streaming on resume.  Save the state properly so that resume
works.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The V4L1 spec says that the image size should be with with VIDIOCSWIN before
requesting buffers with VIDIOCGMBUF and capturing into them with
VIDIOCMCAPTURE.

But it seems that many apps don't do this.  They set the size using the fields
in the VIDIOCMCAPTURE ioctl.  The driver doesn't know what size to capture
until it actually starts to capture.  In particular, it doesn't know what size
to capture until it has already mmap the captured buffers.  Which is quite
stupid.  Why V4L1 has size and format fields for VIDIOCMCAPTURE I have no idea.

Many drivers don't support this, including those using v4l1-compat.

The bttv does, which is probably the only reason such broken software is so
prevalent.

But, the driver doesn't adjust its idea of what size is being captured when it
is set this way.  If you try to query the driver's current setting with
v4l2-ctl, it won't be correct.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The bttv driver instists that the depth specified in the call to VIDIOCSPICT
match the pixel format specified in the same call.

vlc doesn't set the depth field, which makes the SPICT ioctl always fail.

The V4L1 standard is not clear on how most operation are supposed to work, and
this is no exception.  The depth field would appear to be entirely redundant,
as the pixel format specifies a specific depth.  It could be that this field
was only meant for output from the *G*PICT ioctl and should be ignored in
*S*PICT.  This is in fact what the v4l1-compat wrapper does.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  ieee1394: iso and async streams: s/g list fix

I have a system here that actively relies upon RTC wake alarms, and it
has been failing (again) for a few days when attempting to use the
/sys/class/rtc/rtc?/wakealarm interface.

The old (fixed by Linus) /proc/ interface still works, but I'd like to
get it using the new one.

This patch fixes rtc-cmos to ignore the two upper bits when reading the
BCD mday (day of month) register from CMOS.  Some systems (eg.  mine)
seem to have the top bit set to "1" for some reason.

The older /proc/ interface ignores the upper bits, and so we should too.
Signed-off-by: NMark Lord <mlord@pobox.com>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Torsten Kaiser wrote:
> Looking that calltrace upwards, it seems replacing the
> memset(dma->sglist,...) with sg_init_table(...) would fix the BUG_ON()
> as that inits the SG_MAGIC.
Tested-by: NTorsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  [BLOCK] Don't allow empty barriers to be passed down to queues that don't grok them
  dm: bounce_pfn limit added
  Deadline iosched: Fix batching fairness
  Deadline iosched: Reset batch for ordered requests
  Deadline iosched: Factor out finding latter reques

* 'sg' of git://git.kernel.dk/linux-2.6-block:
  [SG] Get rid of __sg_mark_end()
  cleanup asm/scatterlist.h includes
  SG: Make sg_init_one() use general table init functions

Merge branch 'v2.6.24-rc1-lockdep' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep

* 'v2.6.24-rc1-lockdep' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep:
  lockdep: fix a typo in the __lock_acquire comment
  sched: fix unconditional irq lock
  lockdep: fixup irq tracing

* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh64-2.6:
  sh64: Update defconfigs.
  sh64: fix dma_cache_sync() compilation
  sh64: Move DMA macros from pci.h to scatterlist.h.

* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (24 commits)
  sh: Update r7785rp defconfig.
  sh: mach-type updates.
  sh: Fix up r7780rp highlander CF access size.
  sh: Terminate .eh_frame in VDSO with a 4-byte 0.
  sh: Correct SUBARCH matching.
  sh: Decouple 4k and soft/hardirq stacks.
  sh: Fix optimized __copy_user() movca.l usage.
  sh: Clean up SR.RB Kconfig mess.
  sh: Kill off dead ipr_irq_demux().
  sh: Make SH7750 oprofile compile again.
  sh: Provide a __read_mostly section wrapper.
  sh: linker script tidying.
  sh: Move zero page param defs somewhere sensible.
  sh: Use generic SMP_CACHE_BYTES/L1_CACHE_ALIGN.
  sh: Kill off legacy embedded ramdisk section.
  sh: Fix up early mem cmdline parsing.
  sh: Enable USBF on MS7722SE.
  sh: Add resource of USBF for SH7722.
  maple: Fix maple bus compiler warning
  sh: fix zImage build with >=binutils-2.18
  ...

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (23 commits)
  libata: don't configure downstream links faster than the upstream link
  libata: request PHY speed configuration on SControl access failure
  libata: consider errors not associated with commands for speed down
  libata: more robust reset failure handling
  libata: cosmetic clean up / reorganization of ata_eh_reset()
  libata: fix timing computation in ata_eh_reset()
  libata: increase 128 KB / cmd limit for ATAPI tape drives
  sata_promise: fix endianess bug in ASIC PRD bug workaround
  libata: fix docbook
  make ata_scsi_lpm_get() static
  libata: suppress two warnings
  ata/sata_fsl: Remove ata_scsi_suspend/resume callbacks
  ata/sata_fsl: Remove sending LOG EXT command in sata_fsl_softreset()
  ata/sata_fsl: Move MPC8315DS link speed limit workaround to specific ifdef
  ata/sata_fsl: cleanup style problem
  ata/sata_fsl: remove unneeded sata_fsl_hardreset()
  ata/sata_fsl: remove unneeded on-stack copy of FIS
  ata/sata_fsl: cleanup needless casts to/from void __iomem *
  ata/sata_fsl: Remove unnecessary SCR cases
  ata/sata_fsl: Kill ata_sg_is_last()
  ...

The regression was caused by:
        commit[a32ea1e1] Fix read/truncate race

This causes ntfs_readpage() to be called for a zero i_size inode, which
failed when the file was compressed and non-resident.

Thanks a lot to Mike Galbraith for reporting the issue and tracking down
the commit that caused the regression.

Looking into it I found three bugs which the patch fixes.
Signed-off-by: NAnton Altaparmakov <aia21@cantab.net>
Tested-by: NMike Galbraith <efault@gmx.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There's nothing to be gained by configuring downstream links faster
than the upstream link and such configurations cause problems on
certain PMPs.  Limit downstream link speed by the upstream link speed.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In sata_set_spd_needed(), if SControl read failed, it returned 0 and
skipped PHY speed configuration.  However, if SControl access fails,
it's far more logical to request PHY speed configuration.  Reverse the
logic.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

libata EH used to ignore errors not associated with commands when
determining whether speed down is necessary or not.  This leads to the
following problems.

* Errors not associated with commands can occur indefinitely without
  libata EH taking corrective actions.

* Upstream link errors don't trigger speed down when PMP is attached
  to it and commands issued to downstream device trigger errors on the
  upstream link.

This patch makes ata_eh_link_autopsy() consider errors not associated
with command for speed down.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Reset failure is a critical error.  It results in disabling the link
requiring user intervention to re-enable it.  Make reset failure
handling more robust such that libata EH doesn't give up too early.

* Temporary glitches during hardreset may lead to classification
  failure when there's no softreset available.  Retry instead of
  giving up.

* Initial softreset or follow up softreset may fail classification.
  Move classification error handling block out of followup softreset
  block such that both cases are handled and retry instead of giving
  up.  Also, on the last try, give ATA class a blind shot.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Clean up and reorganize ata_eh_reset() to ease further changes.

* Cache ARRAY_SIZE(ata_eh_reset_timeouts) in @max_tries.
* Cache link->flags in @lflags.
* Move failure handling block to the end of the function and unnest
  both success and failure handling blocks.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As jiffies changes asynchronously, it needs to be cached if unchanging
timestamp is needed.  The code in ata_eh_reset() intended to do that
with @now but never actually did it.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Commands sent to ATAPI tape drives via the SCSI generic (sg) driver are
limited in the amount of data that they can transfer by the max_sectors
value.  The max_sectors value is currently calculated according to the
command set for disk drives, which doesn't apply to tape drives.  The
default max_sectors value of 256 limits ATAPI tape drive commands to
128 KB.  This patch against 2.6.24-rc1 increases the max_sectors value
for tape drives to 65535, which permits tape drive commands to transfer
just under 32 MB.

Tested with a SuperMicro PDSME motherboard, AHCI, and a Sony SDX-570V
SATA tape drive.

Note that some of the chipset drivers also set their own max_sectors
value, which may override the value set in libata-core.  I don't have
any of these chipsets to test, so I didn't go messing with them.  Also,
ATAPI devices other than tape drives may benefit from similar changes,
but I have only tape drives and disk drives to test.
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The original workaround for the Promise ASIC PRD bug
contained an endianess bug which I failed to detect:
the adjustment of the last PRD entry's length field
applied host arithmetic to little-endian data, which
is incorrect on big-endian machines.

We have the length available in host-endian format, so
do the adjustment on host-endian data and then convert
and store it in the PRD entry's little-endian data field.

Thanks to an anonymous reviewer for detecting this bug.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix docbook format in the comments.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_scsi_lpm_get() can become static.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

drivers/ata/libata-core.c:768: warning: 'ata_lpm_enable' defined but not used
drivers/ata/libata-core.c:784: warning: 'ata_lpm_disable' defined but not used
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJeff Garzik <jeff@garzik.org>