The SYSTEMPORT driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2017-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.14

rsi driver is getting a lot of new features lately, but as usual
active development happening on iwlwifi as well as other drivers.

I pulled wireless-drivers to fix multiple conflicts in iwlwifi and to
make it easier further development.

Major changes:

ath10k

* initial UBS bus support (no full support yet)

* add tdls support for 10.4 firmware

ath9k

* add Dell Wireless 1802

wil6210

* support FW RSSI reporting

rsi

* support legacy power save, U-APSD, rf-kill and AP mode

* RTS threshold configuration

brcmfmac

* support CYW4373 SDIO/USB chipset

iwlwifi

* some more code moved to a new directory

* add new PCI ID for 7265D
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clk_div_table are not supposed to change at runtime.
meson8b_dwmac structure is working with const clk_div_table.
So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jesper Dangaard Brouer says:

====================
XDP redirect tracepoints

I feel this is as far as I can take the tracepoint infrastructure to
assist XDP monitoring.

Tracepoints comes with a base overhead of 25 nanosec for an attached
bpf_prog, and 48 nanosec for using a full perf record. This is
problematic for the XDP use-case, but it is very convenient to use the
existing perf infrastructure.

From a performance perspective, the real solution would be to attach
another bpf_prog (that understand xdp_buff), but I'm not sure we want
to introduce yet another bpf attach API for this.

One thing left is to standardize the possible err return codes, to a
limited set, to allow easier (and faster) mapping into a bpf map.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This tool xdp_monitor demonstrate how to use the different xdp_redirect
tracepoints xdp_redirect{,_map}{,_err} from a BPF program.

The default mode is to only monitor the error counters, to avoid
affecting the per packet performance. Tracepoints comes with a base
overhead of 25 nanosec for an attached bpf_prog, and 48 nanosec for
using a full perf record (with non-matching filter).  Thus, default
loading the --stats mode could affect the maximum performance.

This version of the tool is very simple and count all types of errors
as one.  It will be natural to extend this later with the different
types of errors that can occur, which should help users quickly
identify common mistakes.

Because the TP_STRUCT was kept in sync all the tracepoints loads the
same BPF code.  It would also be natural to extend the map version to
demonstrate how the map information could be used.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For supporting XDP_REDIRECT, a device driver must (obviously)
implement the "TX" function ndo_xdp_xmit().  An additional requirement
is you cannot TX out a device, unless it also have a xdp bpf program
attached. This dependency is caused by the driver code need to setup
XDP resources before it can ndo_xdp_xmit.

Update bpf samples xdp_redirect and xdp_redirect_map to automatically
attach a dummy XDP program to the configured ifindex_out device.  Use
the XDP flag XDP_FLAGS_UPDATE_IF_NOEXIST on the dummy load, to avoid
overriding an existing XDP prog on the device.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Creating as specific xdp_redirect_map variant of the xdp tracepoints
allow users to write simpler/faster BPF progs that get attached to
these tracepoints.

Goal is to still keep the tracepoints in xdp_redirect and xdp_redirect_map
similar enough, that a tool can read the top part of the TP_STRUCT and
produce similar monitor statistics.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a need to separate the xdp_redirect tracepoint into two
tracepoints, for separating the error case from the normal forward
case.

Due to the extreme speeds XDP is operating at, loading a tracepoint
have a measurable impact.  Single core XDP REDIRECT (ethtool tuned
rx-usecs 25) can do 13.7 Mpps forwarding, but loading a simple
bpf_prog at the tracepoint (with a return 0) reduce perf to 10.2 Mpps
(CPU E5-1650 v4 @ 3.60GHz, driver: ixgbe)

The overhead of loading a bpf-based tracepoint can be calculated to
cost 25 nanosec ((1/13782002-1/10267937)*10^9 = -24.83 ns).

Using perf record on the tracepoint event, with a non-matching --filter
expression, the overhead is much larger. Performance drops to 8.3 Mpps,
cost 48 nanosec ((1/13782002-1/8312497)*10^9 = -47.74))

Having a separate tracepoint for err cases, which should be less
frequent, allow running a continuous monitor for errors while not
affecting the redirect forward performance (this have also been
verified by measurements).
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Given previous patch expose the map_id, it seems natural to also
report the bpf prog id.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make sense of the map index, the tracepoint user also need to know
that map we are talking about.  Supply the map pointer but only expose
the map->id.

The 'to_index' is renamed 'to_ifindex'.  In the xdp_redirect_map case,
this is the result of the devmap lookup. The map lookup key is exposed
as map_index, which is needed to troubleshoot in case the lookup failed.
The 'to_ifindex' is placed after 'err' to keep TP_STRUCT as common as
possible.

This also keeps the TP_STRUCT similar enough, that userspace can write
a monitor program, that doesn't need to care about whether
bpf_redirect or bpf_redirect_map were used.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Supplying the action argument XDP_REDIRECT to the tracepoint xdp_redirect
is redundant as it is only called in-case this action was specified.

Remove the argument, but keep "act" member of the tracepoint struct and
populate it with XDP_REDIRECT.  This makes it easier to write a common bpf_prog
processing events.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Howells says:

====================
rxrpc: Miscellany

Here are a number of patches that make some changes/fixes and add a couple
of extensions to AF_RXRPC for kernel services to use.  The changes and
fixes are:

 (1) Use time64_t rather than u32 outside of protocol or
     UAPI-representative structures.

 (2) Use the correct time stamp when loading a key from an XDR-encoded
     Kerberos 5 key.

 (3) Fix IPv6 support.

 (4) Fix some places where the error code is being incorrectly made
     positive before returning.

 (5) Remove some white space.

And the extensions:

 (6) Add an end-of-Tx phase notification, thereby allowing kAFS to
     transition the state on its own call record at the correct point,
     rather than having to do it in advance and risk non-completion of the
     call in the wrong state.

 (7) Allow a kernel client call to be retried if it fails on a network
     error, thereby making it possible for kAFS to iterate over a number of
     IP addresses without having to reload the Tx queue and re-encrypt data
     each time.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
addrlabel: don't use rtnl locking

addrlabel doesn't appear to require rtnl lock as the addrlabel
table uses a spinlock to serialize add/delete operations.

Also, entries are reference counted so it should be safe
to call the rtnl ops without the rtnl mutex.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There appears to be no need to use rtnl, addrlabel entries are refcounted
and add/delete is serialized by the addrlabel table spinlock.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the IRDA code has moved under drivers/staging/irda/, update the
MAINTAINERS file with the new location.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When bnxt VF-reps are not compiled in (CONFIG_BNXT_SRIOV is off)
bnxt_tc.c needs a dummy definition of the routine bnxt_vf_rep_get_fid().
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Fixes: 2ae7408f ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow a client call that failed on network error to be retried, provided
that the Tx queue still holds DATA packet 1.  This allows an operation to
be submitted to another server or another address for the same server
without having to repackage and re-encrypt the data so far processed.

Two new functions are provided:

 (1) rxrpc_kernel_check_call() - This is used to find out the completion
     state of a call to guess whether it can be retried and whether it
     should be retried.

 (2) rxrpc_kernel_retry_call() - Disconnect the call from its current
     connection, reset the state and submit it as a new client call to a
     new address.  The new address need not match the previous address.

A call may be retried even if all the data hasn't been loaded into it yet;
a partially constructed will be retained at the same point it was at when
an error condition was detected.  msg_data_left() can be used to find out
how much data was packaged before the error occurred.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Add a callback to rxrpc_kernel_send_data() so that a kernel service can get
a notification that the AF_RXRPC call has transitioned out the Tx phase and
is now waiting for a reply or a final ACK.

This is called from AF_RXRPC with the call state lock held so the
notification is guaranteed to come before any reply is passed back.

Further, modify the AFS filesystem to make use of this so that we don't have
to change the afs_call state before sending the last bit of data.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Remove indentation from some blank lines.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

call->error is stored as 0 or a negative error code.  Don't negate this
value (ie. make it positive) before returning it from a kernel function
(though it should still be negated before passing to userspace through a
control message).
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Fix IPv6 support in AF_RXRPC in the following ways:

 (1) When extracting the address from a received IPv4 packet, if the local
     transport socket is open for IPv6 then fill out the sockaddr_rxrpc
     struct for an IPv4-mapped-to-IPv6 AF_INET6 transport address instead
     of an AF_INET one.

 (2) When sending CHALLENGE or RESPONSE packets, the transport length needs
     to be set from the sockaddr_rxrpc::transport_len field rather than
     sizeof() on the IPv4 transport address.

 (3) When processing an IPv4 ICMP packet received by an IPv6 socket, set up
     the address correctly before searching for the affected peer.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

When an XDR-encoded Kerberos 5 ticket is added as an rxrpc-type key, the
expiry time should be drawn from the k5 part of the token union (which was
what was filled in), rather than the kad part of the union.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Since the 'expiry' variable of 'struct key_preparsed_payload' has been
changed to 'time64_t' type, which is year 2038 safe on 32bits system.

In net/rxrpc subsystem, we need convert 'u32' type to 'time64_t' type
when copying ticket expires time to 'prep->expiry', then this patch
introduces two helper functions to help convert 'u32' to 'time64_t'
type.

This patch also uses ktime_get_real_seconds() to get current time instead
of get_seconds() which is not year 2038 safe on 32bits system.
Signed-off-by: NBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: NDavid Howells <dhowells@redhat.com>

We probably don't want to enable code supporting particular hardware by
default e.g. when someone does 'make defconfig'. Other ethernet modules
don't do it.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Updates.

Various changes including updated firmware interface, improved TX ring
allocation scheme, improved out-of-memory logic in NAPI loop, reduced
default rings on multi-port devices, new PCI IDs. Of particular note,

CPU affinity hints from Vasundhara Volam.

TC Flower eswitch support from Sathya Perla.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to implement TC_CLSFLOWER_STATS TC-cmd and the
required FW code to query the stats from the HW.
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the hwrm_cfa_flow_alloc/free() routines
that are needed to issue the FW cmds needed for TC flower offload.
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for offloading TC based flow
rules and actions for the 'flower' classifier in the bnxt_en driver.
It includes logic to parse flow rules and actions received from the
TC subsystem, store them and issue the corresponding
hwrm_cfa_flow_alloc/free FW cmds. L2/IPv4/IPv6 flows and drop,
redir, vlan push/pop actions are supported in this patch.

In this patch the hwrm_cfa_flow_xxx routines are just stubs.
The code for these routines is introduced in the next patch for easier
review. Also, the code to query the TC/flower action stats will
be introduced in a subsequent patch.
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The routine bnxt_link_bp_to_dl() is used to set the devlink ptr
in bnxt struct (bp) and also to set the bnxt back ptr in
the devlink struct.  If devlink_register() fails, bp->dl must
be cleared which is not happening currently. This patch fixes
bnxt_link_bp_to_dl() to clear bp->dl by passing  a NULL dl ptr.

Fixes: 4ab0c6a8 ("bnxt_en: add support to enable VF-representors")
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce default rings from 8 to 4 on multi-port cards to reduce memory
usage.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we cannot allocate RX buffers in the NAPI poll loop when processing
an RX event, the current code does not count that event towards the NAPI
budget.  This can cause us to potentially loop forever in NAPI if we
consistently cannot allocate new buffers.  Improve it by counting
-ENOMEM event as 1 towards the NAPI budget.

Cc: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Reported-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

initialize board_info values with proper enums for defensive programming
purposes.  This will avoid any errors of the enums being declared not
lining up with the board_info array.
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add PCIe device ID for bcm58802 and bcm58808. Also add chip number
update to declare bcm588xx as chip class phase 4 and later
Signed-off-by: NRay Jui <ray.jui@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides hints to irqbalance to map bnxt_en device IRQs
to specific CPU cores. cpumask_local_spread() is used, which first
maps IRQs to near NUMA cores; when those cores are exhausted, IRQs
are mapped to far NUMA cores.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the number of TX rings is changed (e.g. ethtool -L, enabling XDP TX
rings, etc), the current code tries to reserve the new number of TX rings
before closing and re-opening the NIC.  If we are unable to reserve the
new TX rings, we abort the operation and keep the current TX rings.

The problem is that the firmware will disable the current TX rings even
when it cannot reserve the new set of TX rings.  We fix it as follows:

1. Instead of reserving the new set of TX rings, just ask the firmware
to check if the new set of TX rings is available.  There is a flag in
the firmware message to do that.  If not available, abort and the
current TX rings will not be disabled.

2. Do the actual TX ring reservation in the path that opens the NIC.
We keep the number of TX rings currently successfully reserved.  If the
number of TX rings is different than the reserved TX rings, we call
firmware and reserve again.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow APIs are added in this firmware interface.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Samuel Mendoza-Jonas says:

====================
NCSI VLAN Filtering Support

This series (mainly patch 2) adds VLAN filtering to the NCSI implementation.
A fair amount of code already exists in the NCSI stack for VLAN filtering but
none of it is actually hooked up. This goes the final mile and fixes a few
bugs in the existing code found along the way (patch 1).

Patch 3 adds the appropriate flag and callbacks to the ftgmac100 driver to
enable filtering as it's a large consumer of NCSI (and what I've been
testing on).

v3:	- Add comment describing change to ncsi_find_filter()
	- Catch NULL in clear_one_vid() from ncsi_get_filter()
	- Simplify state changes when kicking updated channel
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register the ndo_vlan_rx_{add,kill}_vid callbacks and set the
NETIF_F_HW_VLAN_CTAG_FILTER if NCSI is available.
This allows the VLAN core to notify the NCSI driver when changes occur
so that the remote NCSI channel can be properly configured to filter on
the set VLAN tags.
Signed-off-by: NSamuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of the ndo_vlan_rx_{add,kill}_vid callbacks to have the NCSI
stack process new VLAN tags and configure the channel VLAN filter
appropriately.
Several VLAN tags can be set and a "Set VLAN Filter" packet must be sent
for each one, meaning the ncsi_dev_state_config_svf state must be
repeated. An internal list of VLAN tags is maintained, and compared
against the current channel's ncsi_channel_filter in order to keep track
within the state. VLAN filters are removed in a similar manner, with the
introduction of the ncsi_dev_state_config_clear_vids state. The maximum
number of VLAN tag filters is determined by the "Get Capabilities"
response from the channel.
Signed-off-by: NSamuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>