The Lager board uses the ethernet PHY LED0 as a link signal connected to
the ethernet controller. Specify the corresponding LED mode for the PHY.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add DTS gpio-keys support for SW2 on the Koelsch board.
This makes the DT code match the legacy board code. Also
update the existing gpio-keys nodes to make use of KEY_n.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add DTS gpio-keys support for SW2 on the Lager board.
This makes the DT code match the legacy board code.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add Spansion s25fl008k SPI FLASH and MTD partition, based on bockw legacy
board code.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

  - Add "renesas,hspi-r8a7779" compatible value,
  - Correct reference to parent interrupt controller
    (use "interrupt-parent" instead of "interrupt-controller"),
  - Add missing "#address-cells" and "#size-cells" properties, which are
    needed when populating the SPI buses.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

  - Add "renesas,hspi-r8a7778" compatible value,
  - Correct reference to parent interrupt controller
    (use "interrupt-parent" instead of "interrupt-controller"),
  - Add missing "#address-cells" and "#size-cells" properties, which are
    needed when populating the SPI buses.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add pinctrl and SPI device for MSIOF on Koelsch.
On this board, only MSIOF0 is in use. Its bus contains a single device
(a Renesas R2A11302FT PMIC), for which no bindings are defined yet.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add pinctrl and SPI device for MSIOF on Lager.
On this board, only MSIOF1 is in use. Its bus contains a single device
(a Renesas R2A11302FT PMIC), for which no bindings are defined yet.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Prepare for the advent of MSIOF SPI, which will be spi1 to spi3.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Prepare for the advent of MSIOF SPI, which will be spi1 to spi4.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The correct maximum CPU frequency for r8a7791 is 1500 MHz
so update the r8a7791 SoC DTS to reflect this.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The patch adds asm macros for inc_preempt_count and dec_preempt_count_ti
(which also gets the current thread_info) instead of open-coding them in
arch/arm/vfp/*.S files.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NArun KS <getarunks@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

asm/assembler.h is a better place for this macro since it is used by
asm files outside arch/arm/kernel/
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NArun KS <getarunks@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Check cpu id in pj4_cp0_init. So for no-PJ4 V7 cpus,
pj4_cpu0_init just return.
This fix will help to make the all the V7 cpus(PJ4 and no-PJ4)
can use code.
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Reviewed-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NMatt Porter <mporter@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The patch add cpu_is_pj4 at arch/arm/include/asm/cputype.h
PJ4 has some differences with V7, for example the coprocessor.
To disinguish this kind of situation. cpu_is_pj4 is needed.
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Reviewed-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NMatt Porter <mporter@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

arm_pm_restart(), arm_pm_idle() and soft_restart() are all declared in
system_misc.h, but this file is not included in process.c.  Add this
missing include.  Found via sparse:

arch/arm/kernel/process.c:98:6: warning: symbol 'soft_restart' was not declared. Should it be static?
arch/arm/kernel/process.c:127:6: warning: symbol 'arm_pm_restart' was not declared. Should it be static?
arch/arm/kernel/process.c:134:6: warning: symbol 'arm_pm_idle' was not declared. Should it be static?
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If the renamed symbol is defined lib/iomap.c implements ioport_map and
ioport_unmap and currently (nearly) all platforms define the port
accessor functions outb/inb and friend unconditionally.  So
HAS_IOPORT_MAP is the better name for this.

Consequently NO_IOPORT is renamed to NO_IOPORT_MAP.

The motivation for this change is to reintroduce a symbol HAS_IOPORT
that signals if outb/int et al are available.  I will address that at
least one merge window later though to keep surprises to a minimum and
catch new introductions of (HAS|NO)_IOPORT.

The changes in this commit were done using:

	$ git grep -l -E '(NO|HAS)_IOPORT' | xargs perl -p -i -e 's/\b((?:CONFIG_)?(?:NO|HAS)_IOPORT)\b/$1_MAP/'
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Strictly speaking this call is a no-op on the platform where dcscb.c is
used since it only has architected caches.  The call was there as a hint
to people inspired by this code when writing their own backend, but the
hint might not always be correct.

For example, if a PL310 were to be used it wouldn't be safe to call
the regular outer_flush_all() as atomic instructions for locking
are involved in that case and those instructions cannot be assumed to
still be operational after v7_exit_coherency_flush() has returned.
Given no other CPUs (in the cluster) should be running at that point
then standard concurrency concerns wouldn't apply.

So let's simply kill this call for now and enhance the existing comment.
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On non-LPAE ARMv6+, read-only PMD bits are defined with the combination
"PMD_SECT_APX | PMD_SECT_AP_WRITE". Adjusted the bit masks to correctly
report this.
Signed-off-by: NKees Cook <keescook@chromium.org>
Tested-by: NLaura Abbott <lauraa@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When we configure CONFIG_ARM_LPAE=y, pfn << PAGE_SHIFT will
overflow if pfn >= 0x100000 in copy_oldmem_page.
So use __pfn_to_phys for converting.
Signed-off-by: NLiu Hua <sdu.liu@huawei.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use of tracers in local_irq_disable is causes abort loops when called
with irqs disabled using a temporary stack.  Replace local_irq_disable
with raw_local_irq_disable instead to avoid tracers.
Signed-off-by: NSebastian Capella <sebastian.capella@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The patch changes fimd node status to OK.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch changes fimd node status to OK.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats2.
It adds also trats2 specific properties for DSI
and regulator required by panel.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats.
It adds also trats specific properties for DSI.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This is a common part of DSI node for all Exynos4 boards.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch replaces panel bindings for panel initialized by boot loader
with bindings to proper ld9040 panel.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Remove pdata quirks for the displays on boards that are now supported
properly with DT.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Export the DMA register information from the SoC specific data, such
that we can access the registers directly in omap-dma.c, mapping the
register region ourselves as well.

Rather than calculating the DMA channel register in its entirety for
each access, we pre-calculate an offset base address for the allocated
DMA channel and then just use the appropriate register offset.
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The omap_system_dma_plat_info structure is only seven words, it's not
worth the expense of kmalloc()'ing backing store for this only to
release it later.  Note that platform_device_add_data() copies the
data anyway.  Clean up the initialisation of this structure - we don't
even need code to initialise most of this structure.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This really needs to be there, because otherwise the plat-omap code can
kfree() this data structure, and then re-use the pointer later.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There's no need for this to be a global variable; move it into the
errata configuration function instead.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We can do much better with this by using a structure to describe each
register, rather than code.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

dma_stride and dma_common_ch_start are only ever initialised to one
known value at initialisation, and are private to each of these files.
There's no point these being variables at all.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The disable_irq_lch method is never actually used, so there's not much
point it existing; remove it.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Provide and use a hook to obtain the underlying DMA platform operations
so that omap-dma.c can access the hardware more directly without
involving the legacy DMA driver.
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Switch the device tree to the new compatibles introduced in the RTC
drivers to have a common pattern accross all Allwinner SoCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>