Both callers of mmc_start_request() call mmc_card_removed()
so move that call into mmc_start_request().

This patch is preparation for adding re-tuning support.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For each MMC, SD and SDIO there is code that
holds the clock, calls ops->execute_tuning, and
releases the clock. Simplify the code a bit by
providing a separate function to do that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This ensures that all standard options are available to hsmmc,
In particular, I need cap-power-off-card.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Using the common code removes some code duplication, and
makes it easier to switch to using mmc_of_parse() which
will remove more duplication.

This uses the new mmc_gpio_request_cd_isr to provide a non-standard
interrupt service routine for card-detect interrupts.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

One of the reasons omap_hsmmc doesn't use the slot-gpio library
is that it has some non-standard functionality in the card-detect
interrupt service routine.

To make it possible for omap_hsmmc (and maybe others) to be converted
to use slot-gpio, add 'mmc_gpio_request_cd_isr' which provide an
alternate isr to be register by the slot-gpio code.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Just fix the comments, no functional changes.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enable power cycle and re-initialization of SD cards via the reset
bus_ops. Power cycling a buggy SD card sometimes helps it get back on
track.
Signed-off-by: NJohan Rudholm <johanru@axis.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move the (e)MMC specific hw_reset code from core.c into mmc.c. Call the
code from the new bus_ops member "reset". This also allows for adding
a SD card specific reset procedure.
Signed-off-by: NJohan Rudholm <johanru@axis.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Always check if the card is alive after a successful reset. This allows
us to remove mmc_hw_reset_check(), leaving mmc_hw_reset() as the only
card reset interface.
Signed-off-by: NJohan Rudholm <johanru@axis.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This adds SDIO devicetree subnode parsing to the mmc core. While
SDIO devices are runtime probable they sometimes need nonprobable
additional information on embedded systems, like an additional gpio
interrupt or a clock. This patch makes it possible to supply this
information from the devicetree. SDIO drivers will find a pointer
to the devicenode in their devices of_node pointer.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
[hdegoede@redhat.com: Misc. cleanups]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

While SDIO devices are runtime probable they sometimes need nonprobable
additional information on embedded systems, like an additional gpio
interrupt or a clock. This binding describes how to add child nodes to the
devicetree to supply this information.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
[hdegoede@redhat.com: Documented the need for #address- and #size-cells]
[hdegoede@redhat.com: Added a real world example]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch is based on the patches by Per Forlin, Tony Lin and Ryan QIAN.

This patch complete the API 'post_req' and 'pre_req' in sdhci host side,

Test Env:
1. i.MX6Q-SABREAUTO board, CPU @ 996MHz, use ADMA in uSDHC controller.
2. Test command:
		$ echo 1 > /proc/sys/vm/drop_caches
	write to sd card:
		$ dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=2000 conv=fsync
	read the sd card:
		$ dd if=/dev/mmcblk0 of=/dev/null bs=1M count=2000

3. TOSHIBA 16GB SD3.0 card, running at 4 bit, SDR104 @ 198MHZ
	Performance with and without this patch:
      -------------------------------------------------
	  |                    | read speed | write speed |
	  |------------------------------------------------
	  | with this patch    | ~76.7 MB/s |  ~23.3 MB/s |
	  |------------------------------------------------
	  |without this patch  | ~60.5 MB/s |  ~22.5 MB/s |
	  -------------------------------------------------

4. SanDisk 8GB SD3.0 card, running at 4 bit, DDR50 @ 50MHZ
	Performance with and without this patch:
      -------------------------------------------------
	  |                    | read speed | write speed |
	  |------------------------------------------------
	  | with this patch    | ~40.5 MB/s |  ~15.6 MB/s |
	  |------------------------------------------------
	  |without this patch  | ~36.1 MB/s |  ~14.1 MB/s |
	  -------------------------------------------------

5. Kingston 8GB SD2.0 card, running at 4 bit, High-speed @ 50MHZ
	Performance with and without this patch:
      -------------------------------------------------
	  |                    | read speed | write speed |
	  |------------------------------------------------
	  | with this patch    | ~22.7 MB/s |  ~8.2 MB/s  |
	  |------------------------------------------------
	  |without this patch  | ~21.3 MB/s |  ~8.0 MB/s  |
	  -------------------------------------------------

6. About eMMC, Sandisk 8GB eMMC on i.MX6DL-sabresd board, CPU @ 792MHZ,
   eMMC running at 8 bit, DDR52 @ 52MHZ.
	Performance with and without this patch:
      -------------------------------------------------
	  |                    | read speed | write speed |
	  |------------------------------------------------
	  | with this patch    | ~37.3 MB/s |  ~10.5 MB/s |
	  |------------------------------------------------
	  |without this patch  | ~33.4 MB/s |  ~10.5 MB/s |
	  -------------------------------------------------
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The bounce buffer, used for misaligned bytes for ADMA access,
resides wholly within the (align_sz)-aligned word, just by construction.
The page addresses are aligned to (align_sz), either for 4 or 8 bytes
alignment, so that the aligned word resides wholly within a single page
and can't cross the page boundary. So, the bounce buffer can't cross
the page boundary too. That's why the warnings are never hit, and can
be safely removed.
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since previous patches removed the need for the tuning block patterns
to be exported, let's move them close to the mmc_send_tuning() API.

Those are now intended to be used only by the mmc core.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>

Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API.

This change affects the Exynos variant, since it's the only one which
support the dw_mmc's ->execute_tuning() callback.

It's seems like dw_mmc internal logic expects failed data transfers to
be ended using a stop command. Let the tuning requests also fall into
this category, since there are data transfer involved.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>

Previously the pm_runtime_put() caused the device to be runtime PM
suspended, but then immediately being resumed when we add the host.

Prevent this unnecessary runtime PM suspend/resume cycle during
->probe() by moving the call to pm_runtime_put() after mmc_add_host().
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

By configure runtime PM prior we enable the use of it, we close the gap
for strange and unhandled conditions. Moreover it makes us rely on the
driver core, after finalized ->probe(), to request an inactive device
to become runtime PM idle/suspended, which earlier potentially could
happen already at pm_runtime_set_autosuspend_delay().
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since sdhci_remove_host() access the device, we need to make sure it's
runtime PM resumed.

To handle clock gating properly in remove, we first have to make sure
the clocks are ungated.

To fix both these issues, by invoking pm_runtime_get_sync() early in
->remove() callback. Later once we disabled runtime PM, we can restore
the usage count.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since commit ab78029e (drivers/pinctrl: grab default handles from device
core), we can rely on device core for setting the default pins.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch remove unnecessary 'out of memory' message on dw mmc driver.
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

move function sd_read_data()/sd_write_data() behind
sd_send_cmd_get_rsp() to avoid pre-declaration.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Modify transfer mode for support sdio card,
send cmd and data at the same time for read data transfer,
but send data after cmd for write data transfer.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To support sdio card, transfer mode need make a change,
this need to split code and use it in different place,
Add new function to simplify repeat operation.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

host->cookie is used for handle async request,
we should init it to negative value when new card inserted,
make cookie value invalid.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a new function to dump register within a range.
We print 1 register a line before this patch,
this may make debug info too long when we add more register to dump.

The new dump_reg_range() dump to 8 register a line,
and it is easy to use.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

By moving the allocation of the slot-gpio data into mmc_alloc_host(),
we can remove the slot-gpio internal calls to mmc_gpio_alloc().

This means mmc_gpio_alloc() has now only one caller left, which
consequence allow us to simplify and remove some of the slot-gpio code.

Additionally, this makes the slot-gpio mutex redundant, so let's remove
it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To be consistent when freeing data, let's move the idr_remove() call
from mmc_free_host() into the ->dev_release() callback for the class
device.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As a step in moving slot-gpio functions/structs closer to the MMC core,
let's add a local header file for slot-gpio.

In this initial step we move mmc_gpio_alloc() into the header file,
to make it available for the MMC core. Following patches will show the
utilization of it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We had a mix of using the class device and the parent device while
allocating data through the devm_* managed functions.

Let's be more consistent and always use the parent device.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The slot-gpio uses the devm*_ managed functions. Still it provide APIs
to explicitly free requested CD/WP GPIOs, but these API isn't being
used.

Therefore let's simplify slot-gpio by removing these unused APIs. If it
later turns out we need some of them, we can always consider to restore
the code.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The MMC core makes use of the devm_* functions while requesting the
CD/WP GPIOs, let's rely on that.

Cc: Barry Song <baohua@kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The MMC core makes use of the devm_* functions while requesting the
CD/WP GPIOs, let's rely on that.

Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Instead of just printing an error when mmc_of_parse() fails to request
CD/WP GPIO pins, let's propagate all errors, except for -ENOENT.
Earlier only -EPROBE_DEFER was handled correctly.

As a side effect of this change and by relying on host drivers to
handle the errors during ->probe(), we don't need to free any data in
the error path.

This also means we are actually fixing a bug, since we remove the call
to mmc_gpio_free_cd() which wasn't the correct function to invoke to
handle cleanup. Instead that should have been mmc_gpiod_free_cd().
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

At errors, balance sdhci_pltfm_init() with sdhci_pltfm_free(), to make
sure all data is freed properly.

Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>

Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>

Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.

Cc: Christian Daudt <bcm@fixthebug.org>
Cc: Matt Porter <mporter@linaro.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>

Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.

Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>