This code is after the break statement so it never gets used.  The
"vlan_mac_obj" variable does get initialized properly, so we can just
delete this.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: Dimitris Michailidis <dm@chelsio.com>
Cc: Casey Leedom <leedom@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Jon Mason <mason@myri.com>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Abhishek Kane <v-abkane@microsoft.com>
Cc: devel@driverdev.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Cc: Mark Einon <mark.einon@gmail.com>
Cc: devel@driverdev.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netback currently uses frag->page to store a temporary index reference while
processing incoming requests. Since frag->page is to become opaque switch
instead to using page_offset. Add a wrapper to tidy this up and propagate the
fact that the indexes are only u16 through the code (this was already true in
practice but unsigned long and in were inconsistently used as variable and
parameter types)
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[ Use DMA_TO_DEVICE and dma_mapping_error() -DaveM ]
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82598 and 82599 do not ship with this type of PHY
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is a problem in the ixgbe driver with the reporting of the flow
control parameters. The autoneg parameter is shown to be of if
*either* it really is off, or current modes for both tx and rx are off.

The problem is seen when the parameters are read or set when the link
is down. In this case, the driver sees that tx and rx are currently off
and therefore autoneg parameter is incorrectly reported to be off too.
Also, the ethtool binary can not set the autoneg off since it sees that
it already is. When a link later comes up, the autonegotiation is
carried out normally and the driver later on reports the autoneg
parameter to be on (as it is) and then it can also be changed with
ethtool.

The patch is made against v3.0 kernel, but the problem seems to be there
since v2.6.30-rc1.

Reviewer comments: What we are trying to do is to disable flow control
while the cable is disconnected. Since ixgbe defaults to full flow
control, we call ethtool -A autoneg off rx off tx off while the cable
is disconnected. This doesn't work, because the driver sets
hw->fc.current_mode = ixgbe_fc_none if the cable is unplugged.
ixgbe_get_pauseparam() then reports to ethtool that nothing needs to be
done. The code fixes this, but it might have some unknown consequences.
Signed-off-by: NMika Lansirinne <mika.lansirinne@stonesoft.com>
Reviewed-by: NEsa-Pekka Pyokkimies <esa-pekka.pyokkimies@stonesoft.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Disabling flow control in ixgbe_check_mac_link() results in incorrect
reporting by ethtool when link goes down, so remove it.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

MFLCN register is used to set Rx flow control on parts newer than 82598.

This patch sends the value of MFLCN to ethtool, so it can be used in a
register dump (ethtool -d).
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for new device ID.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes an issue with storing the driver version for the
firmware. If the os does not support the particular firmware
management tools, the firmware requires a driver version to be written
as 0xFFFFFFFF rather than the actual driver version.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since ixgbe_raise_i2c_clk() can never return anything else than 0
this patch removes it's return value and all checks for it.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clear the data field in ixgbe_read_i2c_byte_generic so it does not
accumulate 1 bit using the same variable multiple times.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It some situations the driver sets __IXGBE_RESETTING and then
__IXGBE_DOWN flags. It is possible a link check may sneak in
between.

This patch adds check for both flags.
The idea is to reduce register reads while the PHY is resetting.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The initial function and setup tables can be marked as constant.
Reported-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

drivers/net/built-in.o: In function `bfa_ioc_ct2_poweron':
(.text+0xcdc90): multiple definition of `bfa_ioc_ct2_poweron'
drivers/scsi/built-in.o:(.text+0x17f9a0): first defined here

This patch renames bfa_ioc_ct2_poweron() to bfa_nw_ioc_ct2_poweron() to avoid
multiple definition with Brocade scsi driver. It also modifies asic specific
interface setup to allocate MSIX resources at power on in case of 1860 HW with
no asic block and warns if the asic gen is neither BFI_ASIC_GEN_CT nor
BFI_ASIC_GEN_CT2.
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

check patch was complaining...mostly replaced:
   if ((ret = asix_foo(xx)) < 0) ...
with
   ret = asix_foo(xx);
   if (ret < 0) ...
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Asix provided this patch and I've confirmed "Plugable USB2-E1000" and
"Shenzhen Winstars NWU220G" USB dongles can get a link and TX/RX data.
Signed-off-by: N"Freddy Xin" <freddy@asix.com.tw>
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix phy initialization for AX88772 (USB 2.0 100BT). Failure was
occasionally DHCP wouldn't work after reboot or suspend/resume cycle.

Remove MONITOR_MODE. In this mode, Received packets are not buffered when
the remote wakeup is enabled.
Signed-off-by: N"Freddy Xin" <freddy@asix.com.tw>
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Acked-by: NOlof Johansson <olofj@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

removing obsoleted sysctl,
ip_rt_gc_interval variable no longer used since 2.6.38
Signed-off-by: NVasily Averin <vvs@sw.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mostly PHY access and a few (ugly) debug statements for DMA control.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware is cached during the first successful call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().

It's similar to 953a12cc but the
firmware is mandatory.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This repairs problem with compile library in userspace (libnl).
Signed-off-by: NJiří Župka <jzupka@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allows ss command (iproute2) to display "ecnseen" if at least one packet
with ECT(0) or ECT(1) or ECN was received by this socket.

"ecn" means ECN was negotiated at session establishment (TCP level)

"ecnseen" means we received at least one packet with ECT fields set (IP
level)

ss -i
...
ESTAB      0      0   192.168.20.110:22  192.168.20.144:38016
ino:5950 sk:f178e400
	 mem:(r0,w0,f0,t0) ts sack ecn ecnseen bic wscale:7,8 rto:210
rtt:12.5/7.5 cwnd:10 send 9.3Mbps rcv_space:14480
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following commit removed some including headers:
 "net: sh_eth: move the asm/sh_eth.h to include/linux/"
 (commit id: d4fa0e35)

Then, the build failure happened on the linux-next:

drivers/net/ethernet/renesas/sh_eth.c:601: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/net/ethernet/renesas/sh_eth.c:1970: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: function declaration isn't a prototype
drivers/net/ethernet/renesas/sh_eth.c:1971: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: function declaration isn't a prototype
drivers/net/ethernet/renesas/sh_eth.c:1972: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: function declaration isn't a prototype

This patch fixes the issue. This patch also get back include/kernel.h
and linux/spinlock.h.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The allocation of "phyinfo" wasn't checked, and also the allocation
wasn't freed on error paths.  Sjur Brændeland pointed out as well
that "phy_driver" should be freed on the error path too.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to allow application to update existing fdb entries that already
exist. This makes bridge netlink neighbor API have same flags and
semantics as ip neighbor table.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When port is added to a bridge, the old code would send the new neighbor
netlink message before the subsequent new link message. This bug makes
it difficult to use the monitoring API in an application.

This code changes the ordering to add the forwarding entry
after the port is setup. One of the error checks (for invalid address)
is moved earlier in the process to avoid having to do unwind.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also changing it's frequency to once every 64s instead of existing 32s as
it was shown to affect performance
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was manifesting as a crash when FAT Dump extraction was attempted on a PPC machine.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was showing up as junk value on PPC /Big endian machines since
it was marked as a byte.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>