On CHV, All the freq request should be even. So, we need to make sure we
request the opcode accordingly.

v2: Avoid vairable for freq request (ville)
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I don't see why we wouldn't want interrupts to wake up the CPU from C3
always, so just set the AGPBUSY# bit in gen3_init_clock_gating().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fallout from an intermediate patch revision that I deemed worth saving.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No point in having this indirection.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So apparently this is tricky.

We need to consider:
- We start out with all the hw enabling bits disabled, both the
  individual fifo underrun interrupts and the shared display error
  interrupts masked. Otherwise if the bios config is broken we'll blow
  up with a NULL deref in our interrupt handler since the crtc
  structures aren't set up yet at driver load time.
- On gmch we need to mask fifo underruns on the sw side, so always
  need to set that in sanitize_crtc for those platforms.
- On other platforms we try to set the sw tracking so that it reflects
  the real state. But since a few platforms have shared bits we must
  _not_ disable fifo underrun reporting. Otherwise we'll never enable
  the shared error interrupt.

This is the state before out patch, but unfortunately this is not good
enough. But after a suspend resume operation this is broken:
1. We don't enable the hw interrupts since the same code runs on
resume as on driver load.
2. The fifo underrun state adjustments we do in sanitize_crtc doesn't
fire on resume since (except for hilarious firmware) all pipes are off
at that point. But they also don't hurt since the subsequent crtc
enabling due to force_restore will enable fifo underruns.

Which means when we enable fifo underrun reporting we notice that the
per-crtc state is already correct and short-circuit everthing out. And
the interrupt doesn't get enabled.

A similar problem would happen if the bios doesn't light up anything
when the driver loads. Which is exactly what happens when we reload
the driver since our unload functions disables all outputs.

Now we can't just rip out the short-circuit logic and unconditionally
update the fifo underrun reporting interrupt masking: We have some
checks for shared error interrupts to catch issues that happened when
the shared error interrupt was disabled.

The right fix is to push down this logic so that we can always update
the hardware state, but only check for missed fifo underruns on a real
enabled->disabled transition and ignore them when we're already
disabled.

On platforms with shared error interrupt the pipe CRC interrupts are
grouped together with the fifo underrun reporting this fixes pipe CRC
support after suspend and driver reloads.

Testcase: igt/kms_pipe_crc_basic/suspend-*
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Generated using semantic patches:

@@
expression E;
@@

- drm_get_connector_name(&E)
+ E.name

@@
expression E;
@@

- drm_get_connector_name(E)
+ E->name

v2: Turn drm_get_connector_name(&E) into E.name instead of &(E)->name.
Acked-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Manual cleanup after the previous Coccinelle script.

Yes, I could write another Coccinelle script to do this but I
don't want labor-replacing robots making an honest programmer's
work obsolete (also, I'm lazy).
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This refactoring has been performed using the following Coccinelle
semantic script:

    @@
    struct intel_engine_cs r;
    @@
    (
    - (r).obj
    + r.buffer->obj
    |
    - (r).virtual_start
    + r.buffer->virtual_start
    |
    - (r).head
    + r.buffer->head
    |
    - (r).tail
    + r.buffer->tail
    |
    - (r).space
    + r.buffer->space
    |
    - (r).size
    + r.buffer->size
    |
    - (r).effective_size
    + r.buffer->effective_size
    |
    - (r).last_retired_head
    + r.buffer->last_retired_head
    )

    @@
    struct intel_engine_cs *r;
    @@
    (
    - (r)->obj
    + r->buffer->obj
    |
    - (r)->virtual_start
    + r->buffer->virtual_start
    |
    - (r)->head
    + r->buffer->head
    |
    - (r)->tail
    + r->buffer->tail
    |
    - (r)->space
    + r->buffer->space
    |
    - (r)->size
    + r->buffer->size
    |
    - (r)->effective_size
    + r->buffer->effective_size
    |
    - (r)->last_retired_head
    + r->buffer->last_retired_head
    )

    @@
    expression E;
    @@
    (
    - LP_RING(E)->obj
    + LP_RING(E)->buffer->obj
    |
    - LP_RING(E)->virtual_start
    + LP_RING(E)->buffer->virtual_start
    |
    - LP_RING(E)->head
    + LP_RING(E)->buffer->head
    |
    - LP_RING(E)->tail
    + LP_RING(E)->buffer->tail
    |
    - LP_RING(E)->space
    + LP_RING(E)->buffer->space
    |
    - LP_RING(E)->size
    + LP_RING(E)->buffer->size
    |
    - LP_RING(E)->effective_size
    + LP_RING(E)->buffer->effective_size
    |
    - LP_RING(E)->last_retired_head
    + LP_RING(E)->buffer->last_retired_head
    )

Note: On top of this this patch also removes the now unused ringbuffer
fields in intel_engine_cs.
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
[danvet: Add note about fixup patch included here.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the upcoming patches we plan to break the correlation between
engine command streamers (a.k.a. rings) and ringbuffers, so it
makes sense to refactor the code and make the change obvious.

No functional changes.
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On gen2 the scanline counter behaves a bit differently from the
later generations. Instead of adding one to the raw scanline
counter value, we must subtract one.

On HSW/BDW the scanline counter requires a +2 adjustment on HDMI
outputs. DP outputs on the on the other require the typical +1
adjustment.

As the fixup we must apply to the hardware scanline counter
depends on several factors, compute the desired offset at modeset
time and tuck it away for when it's needed.

v2: Clarify HSW+ situation
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78997Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The docs are a bit lacking when it comes to describing when certain
timing related events occur in the hardware. Draw a picture which
tries to capture the most important ones.

v2: Clarify a few details (Imre)
v3: Add HSW+ HDMI scanline counter numbers
Acked-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NAkash Goel <akash.goels@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently the logic to fix up the frame counter on gen3/4 assumes that
start of vblank occurs at vblank_start*htotal pixels, when in fact
it occurs htotal-hsync_start pixels earlier. Apply the appropriate
adjustment to make the frame counter more accurate.

Also fix the vblank start position for interlaced display modes.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In interlaced modes, the pixel counter counts all pixels,
so one field will have htotal more pixels. In order to avoid
the reported position from jumping backwards when the pixel
counter is beyond the length of the shorter field, just
clamp the position the length of the shorter field. This
matches how the scanline counter based position works since
the scanline counter doesn't count the two half lines.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Checking whether the error interrupt was enabled or not isn't really
necessary when we check for uncleared FIFO underruns. If it was enabled
we'll race with the interrupt handler a bit, but that seems OK as we
still claim the interrupt.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NThomas Wood <thomas.wood@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

FIFO underruns don't generate interrupts on gmch platforms, so
if we want to know whether a modeset triggered FIFO underruns we
need to explicitly check for them.

As a modeset on one pipe could cause underruns on other pipes,
check for underruns on all pipes.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NThomas Wood <thomas.wood@intel.com>
[danvet: Fix up merge error, kudos to Ville for noticing it.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

FIFO underruns don't generate an interrupt on gmch platforms, so we
should check whether there were any that we failed to notice when
we're disabling FIFO underrun reporting.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NThomas Wood <thomas.wood@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We don't have hardware based disable bits on gmch platforms, so need
to block spurious underrun reports in software. Which means that we
_must_ start out with fifo underrun reporting disabled everywhere.

This is in big contrast to ilk/hsw/cpt where there's only _one_
disable bit for all platforms and hence we must allow underrun
reporting on disabled pipes. Otherwise nothing really works,
especially the CRC support since that's key'ed off the same irq
disable bit.

This allows us to ditch the fifo underrun reporting hack from the vlv
runtime pm code and unexport the internal function from i915_irq.c
again. Yay!

v2: Keep the display irq disabling, spotted by Imre.

Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAntti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAntti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAntti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some platforms have a shared error interrupt, so if FIFO underrun
reporting gets disabled for one pipe/transcoder it gets disabled
for all pipes/transcoders.

When we disable FIFO underrun reporting we check whether the
interrupt was enabled or not. If it wasn't we might have missed
an underrun and we perform one last check right there. Currently
we print a debug message when an underrun is detect using this
mechanism. Promote the message to DRM_ERROR() to match the other
underrun error messages.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Almost all of it is reusable from the existing code. The primary
difference is we need to do even less in the interrupt handler, since
interrupts are not shared in the same way.

The patch is mostly a copy-paste of the existing snb+ code, with updates
to the relevant parts requiring changes to the interrupt handling. As
such it /should/ be relatively trivial. It's highly likely that I missed
some places where I need a gen8 version of the PM interrupts, but it has
become invisible to me by now.

This patch could probably be split into adding the new functions,
followed by actually handling the interrupts. Since the code is
currently disabled (and broken) I think the patch stands better by
itself.

v2: Move the commit about not touching the ringbuffer interrupt to the
snb_* function where it belongs (Rodrigo)

v3: Rebased on Paulo's runtime PM changes

v4: Not well validated, but rebase on
commit 730488b2
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Fri Mar 7 20:12:32 2014 -0300

    drm/i915: kill dev_priv->pm.regsave

v5: Rebased on latest code base. (Deepak)

v6: Remove conflict markers, Unnecessary empty line and use right
IIR interrupt (Ville)

v7: mask modified without rmw (Ville Syrjälä)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Inspired by a review bikeshed from Jani.

Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV has the Gen8 master interrupt register, as well as Gen8
GT/PCU interrupt registers.

The display block is based on VLV, with the main difference
of adding pipe C.

v2: Rewrite the order of operations to make more sense
    Don't bail out if MASTER_CTL register doesn't show an interrupt,
    as display interrupts aren't reported there.

v3: Rebase on top of Egbert Eich's hpd irq handling rework by using
the relevant port hotplug logic like for vlv.

v4: Rebase on top of Ben's gt irq #define refactoring.

v5: Squash in gen8_gt_irq_handler refactoring from Zhao Yakui
<yakui.zhao@intel.com>

v6: Adapt to upstream changes, dev_priv->irq_received is gone.

v7: Enable 3 the commented-out 3 pipe support.

v8: Rebase on top of Paulo's irq setup rework, use the renamed macros from
upstream.

v9: Grab irq_lock around i915_enable_pipestat()

FIXME: There's probably some potential for more shared code between bdw and chv.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
[danvet: Drop the unnecessary cast Jani spotted.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add a mechanism by which we can evade the leading edge of vblank. This
guarantees that no two sprite register writes will straddle on either
side of the vblank start, and that means all the writes will be latched
together in one atomic operation.

We do the vblank evade by checking the scanline counter, and if it's too
close to the start of vblank (too close has been hardcoded to 100usec
for now), we will wait for the vblank start to pass. In order to
eliminate random delayes from the rest of the system, we operate with
interrupts disabled, except when waiting for the vblank obviously.

Note that we now go digging through pipe_to_crtc_mapping[] in the
vblank interrupt handler, which is a bit dangerous since we set up
interrupts before the crtcs. However in this case since it's the vblank
interrupt, we don't actually unmask it until some piece of code
requests it.

v2: preempt_check_resched() calls after local_irq_enable() (Jesse)
    Hook up the vblank irq stuff on BDW as well
v3: Pass intel_crtc instead of drm_crtc (Daniel)
    Warn if crtc.mutex isn't locked (Daniel)
    Add an explicit compiler barrier and document the barriers (Daniel)
    Note the irq vs. modeset setup madness in the commit message (Daniel)
v4: Use prepare_to_wait() & co. directly and eliminate vbl_received
v5: Refactor intel_pipe_handle_vblank() vs. drm_handle_vblank() (Chris)
    Check for min/max scanline <= 0 (Chris)
    Don't call intel_pipe_update_end() if start failed totally (Chris)
    Check that the vblank counters match on both sides of the critical
    section (Chris)
v6: Fix atomic update for interlaced modes
v7: Reorder code for better readability (Chris)
v8: Drop preempt_check_resched(). It's not available to modules
    anymore and isn't even needed unless we ourselves cause
    a wakeup needing reschedule while interrupts are off
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NSourab Gupta <sourabgupta@gmail.com>
Reviewed-by: NAkash Goel <akash.goels@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This will be helpful in abstracting some of the code in preparation for
gen8 semaphores.

v2: Move mbox stuff to a separate struct

v3: Rebased over VCS2 work

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add a new function intel_get_crtc_scanline() that returns the current
scanline counter for the crtc.

v2: Rebase after vblank timestamp changes.
    Use intel_ prefix instead of i915_ as is more customary for
    display related functions.
    Include DRM_SCANOUTPOS_INVBL in the return value even w/o
    adjustments, for a bit of extra consistency.
v3: Change the implementation to be based on DSL on all gens,
    since that's enough for the needs of atomic updates, and
    it will avoid complicating the scanout position calculations
    for the vblank timestamps
v4: Don't break scanline wraparound for interlaced modes
Reviewed-by: NSourab Gupta <sourabgupta@gmail.com>
Reviewed-by: NAkash Goel <akash.goels@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Seems I've been a bit dense with regards to the start of vblank
vs. the scanline counter / pixel counter.

After staring at the pixel counter on gen4 I came to the conclusion
that the start of vblank interrupt and scanline counter increment
happen at the same time. The scanline counter increment is documented
to occur at start of hsync, which means that the start of vblank
interrupt must also trigger there. Looking at the pixel counter value
when the scanline wraps from vtotal-1 to 0 confirms that, as the pixel
counter at that point reads hsync_start. This also clarifies why we see
need the +1 adjustment to the scaline counter. The counter actually
starts counting from vtotal-1 on the first active line.

I also confirmed that the frame start interrupt happens ~1 line after
the start of vblank, but the frame start occurs at hblank_start instead.
We only use the frame start interrupt on gen2 where the start of vblank
interrupt isn't available. The only important thing to note here is that
frame start occurs after vblank start, so we don't have to play any
additional tricks to fix up the scanline counter.

The other thing to note is the fact that the pixel counter on gen3-4
starts counting from the start of horizontal active on the first active
line. That means that when we get the start of vblank interrupt, the
pixel counter reads (htotal*(vblank_start-1)+hsync_start). Since we
consider vblank to start at (htotal*vblank_start) we need to add a
constant (htotal-hsync_start) offset to the pixel counter, or else we
risk misdetecting whether we're in vblank or not.

I talked a bit with Art Runyan about these topics, and he confirmed my
findings. And that the same rules should hold for platforms which don't
have the pixel counter. That's good since without the pixel counter it's
rather difficult to verify the timings to this accuracy.

So the conclusion is that we can throw away all the ISR tricks I added,
and just increment the scanline counter by one always.
Reviewed-by: NSourab Gupta <sourabgupta@gmail.com>
Reviewed-by: NAkash Goel <akash.goels@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Atm we can end up in the GPU reset deferred work in D3 state if the last
runtime PM reference is dropped between detecting a hang/scheduling the
work and executing the work. At least one such case I could trigger is
the simulated reset via the i915_wedged debugfs entry. Fix this by
getting an RPM reference around accessing the HW in the reset work.

v2:
- Instead of getting/putting the RPM reference in the reset work itself,
  get it already before scheduling the work. By this we also prevent
  going to D3 before the work gets to run, in addition to making sure
  that we run the work itself in D0. (Ville, Daniel)
v3:
- fix inverted logic fail when putting the RPM ref on behalf of a
  cancelled GPU reset work (Ville)
v4:
- Taking the RPM ref in the interrupt handler isn't really needed b/c
  it's already guaranteed that we hold an RPM ref until the end of the
  reset work in all cases we care about. So take the ref in the reset
  work (for cases like i915_wedged_set). (Daniel)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Not clearing this flag causes spurious interrupts at least in D3 state,
so before enabling RPM we need to fix this. We were already setting this
flag when enabling interrupts, only clearing it was missing.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The status bits are unconditionally set, the control bits only enable
the actual interrupt generation. Which means if we get some random
other interrupts we'll bogusly complain about them.

So restrict the WARN to platforms with a sane hotplug interrupt
handling scheme. And even more important also don't attempt to process
the hpd bit since we've detected a storm already. Instead just clear
the bit silently.

This WARN has been introduced in

commit b8f102e8
Author: Egbert Eich <eich@suse.de>
Date:   Fri Jul 26 14:14:24 2013 +0200

    drm/i915: Add messages useful for HPD storm detection debugging (v2)

before that we silently handled the hpd event and so partially
defeated the storm detection.

v2: Pimp commit message (Jani)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Egbert Eich <eich@suse.de>
Cc: bitlord <bitlord0xff@gmail.com>
Reported-by: Nbitlord <bitlord0xff@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

It is now clear that this interrupt is for the primary plane and not
something global to the pipe. It also matches what the spec calls it.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Print the enable_mask and status_mask from
__i915_{enable,disable}_pipestat() when the caller has messed them up
somehow.

v2: Use pipe_name() (Damien)
    Fix a typo in the commit message
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC.  Replace all references to the CRTC fb with the
primary plane's fb.

This patch was generated by the Coccinelle semantic patching tool using
the following rules:

        @@ struct drm_crtc C; @@
        -   (C).fb
        +   C.primary->fb

        @@ struct drm_crtc *C; @@
        -   (C)->fb
        +   C->primary->fb

v3: Generate patch via coccinelle.  Actual removal of crtc->fb has been
    moved to a subsequent patch.

v2: Fixup several lingering crtc->fb instances that were missed in the
    first patch iteration.  [Rob Clark]
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>

Now that we don't keep the hotplug interrupts enabled anymore, we can
kill the regsave struct and just cal the normal IRQ preinstall,
postinstall and uninstall functions. This makes it easier to add
runtime PM support to non-HSW platforms.

The only downside is in case we get a request to update interrupts
while they are disabled, won't be able to update the regsave struct.
But this should never happen anyway, so we're not losing too much.

v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We should only enable interrupts at postinstall.

And now on ILK/SNB/IVB/HSW the irq_preinstall and irq_postinstall
functions leave the hardware in the same state.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail due to drm_i915_private_t typedef removal.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So we can merge all the common code from postinstall and uninstall.

v2: - Rebase.
    - While at it, remove useless { and }.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To merge the common code of ironlake_irq_preinstall and
ironlake_irq_uninstall.

We should also probably do something about that HSWSTAM write on a
later commit.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail due to drm_i915_private_t typedef removal.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Missing from gen8_irq_uninstall.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>