brcmf_sdbrcm_isr doesn't access to the dongle through SDIO bus.
Stop releasing and claiming host in irq handler to eliminate
any potential risk.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device.  The latter needs to be registered
first.

Compile-tested only.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device.  The latter needs to be registered
first.

Compile-tested only.
Reported-by: NCesare Leonardi <celeonar@gmail.com>
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RFCSR is only used in rt2800. For other chipsets, the debug struct
for rfcsr should be zeroed, which isn't be an issue, since the code
can now cope with that.
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow a register to be unspecified, therefore not creating its debugfs
file entry.
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The problem was found by Stefan Lippers-Hollmann
http://marc.info/?l=linux-wireless&m=132720334512946&w=2

WARNING: at /tmp/buildd/linux-aptosid-3.2/debian/build/source_i386_none/net/wireless/core.c:562 wiphy_register+0x45/0x38d [cfg80211]()
Hardware name: TravelMate 290 \xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff
Modules linked in: ipw2200(+) iTCO_wdt libipw joydev drm snd_seq snd_timer snd_seq_device iTCO_vendor_support yenta_socket snd intel_agp i2c_i801 pcmcia_rsrc cfg80211 soundcore parport_pc psmouse parport rng_core snd_page_alloc serio_raw pcspkr i2c_algo_bit intel_gtt pcmcia_core evdev irda crc_ccitt rfkill lib80211 processor container ac battery shpchp pci_hotplug button ext4 mbcache jbd2 crc16 dm_mod sd_mod sr_mod crc_t10dif cdrom ata_generic pata_acpi ata_piix libata scsi_mod firewire_ohci firewire_core crc_itu_t 8139too 8139cp mii uhci_hcd ehci_hcd usbcore usb_common [last unloaded: scsi_wait_scan]
Pid: 328, comm: modprobe Not tainted 3.2-1.slh.4-aptosid-686 #1
Call Trace:
[<c012eaf4>] ? warn_slowpath_common+0x7c/0x8f
[<e0ff0b3e>] ? wiphy_register+0x45/0x38d [cfg80211]
[<e0ff0b3e>] ? wiphy_register+0x45/0x38d [cfg80211]
[<c012eb22>] ? warn_slowpath_null+0x1b/0x1f
[<e0ff0b3e>] ? wiphy_register+0x45/0x38d [cfg80211]
[<c01f89d7>] ? internal_create_group+0xf5/0xff
[<e0a2de1c>] ? ipw_pci_probe+0xa9a/0xbd0 [ipw2200]
[<c01519f4>] ? arch_local_irq_save+0xf/0x14
[<c0252986>] ? pci_device_probe+0x53/0x9a
[<c02c2820>] ? driver_probe_device+0x94/0x124
[<c0252871>] ? pci_match_id+0x15/0x34
[<c02c28f0>] ? __driver_attach+0x40/0x5b
[<c02c1d81>] ? bus_for_each_dev+0x37/0x60
[<c02c25aa>] ? driver_attach+0x17/0x1a
[<c02c28b0>] ? driver_probe_device+0x124/0x124
[<c02c22c4>] ? bus_add_driver+0x92/0x1d1
[<e099d000>] ? 0xe099cfff
[<c02c2cb8>] ? driver_register+0x7d/0xd4
[<c017cd50>] ? jump_label_module_notify+0xec/0x167
[<e099d000>] ? 0xe099cfff
[<c0253017>] ? __pci_register_driver+0x32/0x87
[<e099d000>] ? 0xe099cfff
[<e099d02e>] ? ipw_init+0x2e/0x72 [ipw2200]
[<c0101173>] ? do_one_initcall+0x7d/0x132
[<c0145016>] ? __blocking_notifier_call_chain+0x47/0x4f
[<c0154a73>] ? sys_init_module+0x13a4/0x159c
[<c03a639f>] ? sysenter_do_call+0x12/0x28

This warning appears only if we apply Ben Hutchings' fix
http://marc.info/?l=linux-wireless&m=132720195012653&w=2
for the bug reported by Cesare Leonardi
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=656813
with cfg80211 warning during device registration
("cfg80211: failed to add phy80211 symlink to netdev!").

We separate device bring up and registration with network stack
to avoid the problem.

After that Ben Hutchings' fix can be applied to fix the bug.

Cc: stable@kernel.org
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Tested-by: NStefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change-Id: I10e42e0cc7dd91047f093ea2c5a55d65c004ada6
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Reviewed-on: http://git-mwg.jer.intel.com/gerrit/1939
Tested-by: Jenkins
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

"oui_type" in structure "ieee_types_vendor_header" is not used separately,
so include it in "oui" array. Now complete oui will be compared fixing
following warnings.

drivers/net/wireless/mwifiex/sta_ioctl.c:1410 mwifiex_set_gen_ie_helper()
        error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/sta_ioctl.c:1435 mwifiex_set_gen_ie_helper()
        error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1177 mwifiex_update_bss_desc_with_ie()
        error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1185 mwifiex_update_bss_desc_with_ie()
        error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

	modified:   drivers/net/wireless/mwifiex/Kconfig
	- notate additional chipset
	modified:   drivers/net/wireless/mwifiex/sdio.c
	- add definition of id (0x9116)
	- add to switch for firmware load
	- add MODULE_FIRMWARE
	modified:   drivers/net/wireless/mwifiex/sdio.h
	- add definition of default firmware name
Signed-off-by: NJason Plum <max@warheads.net>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a cut and paste mistake, sizeof(struct mib_local) was intended
instead of sizeof(struct mib_phy).  The call to at76_get_mib() uses
sizeof(struct mib_local) correctly, although I changed that to
sizeof(*m) for style reasons after discussion with some of the wireless
maintainers.

The current code works fine because mib_phy structs are larger than
mib_local structs.  But we may as well clean it up.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This doesn't make any sense. Init it from the transport instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

There are various problems happened on 5GHz band not observed on
2.4 GHz (microcode errors, queue stuck, etc... ) . Also roaming
between 5GHz AP and 2GHz does not work very well. To workaround
the problems add option to disable 5GHz support. This will help
on environments where APs are dual-band, and devices will not try
to associate on band where issues happen.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Also remove a debug print when allocation error occurred.
The kernel will complain anyway.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Add the Loose coex LUT and will use later for better bt coex tpt
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

In bt coex, consider reduce tx power as part of ack/cts kill mask
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Add the reduce tx power information in bt coex host command
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

When bluetooth coex is active and certain condition matched,
driver need to decide should the tx power been reduce or not.
Adding the logic to manage it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Do not assume we have our subsystem including this for us,
at least for older kernels this is not true. Lets just be
explicit about this requirement for the usage of wake_up().
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By default, iwlwifi uses order-1 pages (8 KB) to store incoming frames,
but doesnt say so in skb->truesize.

This makes very possible to exhaust kernel memory since these skb evade
normal socket memory accounting.

As struct ieee80211_hdr is going to be pulled before calling IP stack,
there is no need to use dev_alloc_skb() to reserve NET_SKB_PAD bytes.
alloc_skb() is ok in this driver, allowing more tailroom.

Pull beginning of frame in skb header, in the hope we can reuse order-1
pages in the driver immediately for small frames and reduce their
truesize to the minimum (linear skbs)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit a844adfd.
The commit a844adfd is degrading rx sensitivity of lower rate in
HT40 mode and it is confirmed that reverting the change is
improving rx sensitivity.

spur_freq_sd (for self-corr in AGC) is defined with respect to the
center of each 20MHz channel while spur_phase_delta (for self-corr
in Rx and spur data filter) is defined with respect to the center
of current RF channel.

So in short, we need to subtract spur_freq_sd (for self-corr in AGC)
by the offset between the center of primary20 and the center of RF
channel in SW. This offset could be +/10 MHz for dynamic 40.

Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: NKai Shi <kaishi@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dpc_tl_lock is not acquired in the error handle code for bus down.
But it's unlocked using spin_unlock_irqrestore after finishing task
list walk down. Grab the lock before breaking the loop to avoid a
double unlock.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver currently leaves elp_work behind when stopping, which
occasionally results in data corruption because work function ends
up accessing freed memory, typical symptoms of this are various
worker_thread crashes. Fix it by cancelling elp_work.

Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently SDIO glue frees it's own structure before calling
wl1251_free_hw(), which in turn calls ieee80211_unregister_hw().
The later call may result in a need to communicate with the chip
to stop it (as it happens now if the interface is still up before
rmmod), which means calls are made back to the glue, resulting in
freed memory access.

Fix this by freeing glue data last.

Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 2a190322 (b43: reload phy and bss settings after core restarts)
introduced an unconditional call to b43_op_config() at the end of
b43_op_start(). When firmware fails to load this can wedge the system.
There's no need to reload the configuration after a failed
initialization anyway, so only make the call if initialization was
successful.

BugLink: http://bugs.launchpad.net/bugs/950295
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When our driver device is removed on the AHB bus, our IO memory is never unmapped.
Signed-off-by: NJonathan Bither <jonbither@gmail.com>
Reviewed-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dpc takes care of all data packets transmissions for sdio function
2. It is possible that it misses some completion events when the
traffic is heavy or it's running on a slow cpu. A linked list is
introduced to make sure dpc is invoked whenever needed.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SDIO stack doesn't have a structure for function 0. The structure
pointer stored in card->sdio_func[0] is actually for function 1.
With current implementation the register read/write is applied to
function 1. This pathch fixes the issue.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NFlorian Fainelli <florian@openwrt.org>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* PS_WAIT_FOR_TX_ACK is used in network-sleep mode and checking
  it for handling IDLE transitions is incorrect. Fix this.

* RX PCU/DMA engines have to be stopped before setting the chip into
  full-sleep mode - otherwise the chip becomes mute.

* Make things a bit clear by checking explicitly for network-sleep
  mode in the tx() routine and add a couple of debug statements
  to aid PS debugging.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.

Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.

Note that we don't use queues 20 and higher today and
doing so needs more work than this.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For now at least, all module parameters should be
with the core functionality, so move them there,
while at it rename to iwlwifi_mod_params. Also
rename iwl-shared.h to iwl-modparams.h to reflect
the real contents.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>