Move swdev wrappers over to new swdev ops (from previous ndo ops).  No
functional changes to the implementation.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>

rocker: move to new swdev ops
Signed-off-by: NScott Feldman <sfeldma@gmail.com>

dsa: move to new swdev ops
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass in the netlink flags (NLM_F_*) into switchdev driver for IPv4 FIB add op
to allow driver to 1) optimize hardware updates, 2) handle ip route prepend
and append commands correctly.
Suggested-by: NJamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Acked-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call into the switchdev driver any time an IPv4 fib entry is
added/modified/deleted from the kernel's FIB.  The switchdev driver may or
may not install the route to the offload device.  In the case where the
driver tries to install the route and something goes wrong (device's routing
table is full, etc), then all of the offloaded routes will be flushed from the
device, route forwarding falls back to the kernel, and no more routes are
offloading.

We can refine this logic later.  For now, use the simplist model of offloading
routes up to the point of failure, and then on failure, undo everything and
mark IPv4 offloading disabled.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flesh out ndo wrappers to call into device driver.  To call into device driver,
the wrapper must interate over route's nexthops to ensure all nexthop devs
belong to the same switch device.  Currently, there is no support for route's
nexthops spanning offloaded and non-offloaded devices, or spanning ports of
multiple offload devices.

Since switch device ports may be stacked under virtual interfaces (bonds and/or
bridges), and the route's nexthop may be on the virtual interface, the wrapper
will traverse the nexthop dev down to the base dev.  It's the base dev that's
passed to the switchdev driver's ndo ops.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep switchdev FIB offload model simple for now and don't allow custom ip
rules.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IPv4 fib ndo wrapper funcs and stub them out for now.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds two new api's netdev_switch_port_bridge_setlink
and netdev_switch_port_bridge_dellink to offload bridge port attributes
to switch port

(The names of the apis look odd with 'switch_port_bridge',
but am more inclined to change the prefix of the api to something else.
Will take any suggestions).

The api's look at the NETIF_F_HW_SWITCH_OFFLOAD feature flag to
pass bridge port attributes to the port device.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces new notifier for purposes of exposing events which happen
on switch driver side. The consumers of the event messages are mainly involved
masters, namely bridge and ovs.
Suggested-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To notify switch driver of change in STP state of bridge port, add new
.ndo op and provide switchdev wrapper func to call ndo op. Use it in bridge
code then.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The goal of this is to provide a possibility to support various switch
chips. Drivers should implement relevant ndos to do so. Now there is
only one ndo defined:
- for getting physical switch id is in place.

Note that user can use random port netdevice to access the switch.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Reviewed-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>