* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Ensure all PG_dcache_dirty pages are written back.
  sh: mach-ecovec24: setup.c detailed correction
  serial: sh-sci: Convert tremaining ctrl_xxx I/O routines to __raw_xxx.
  serial: sh-sci: earlyprintk zero uartclk fix
  sh: Only use bl bit toggling for sleeping idle.
  sh: Restore bl bit toggling in idle loop.
  sh: Fix up MAX_DMA_CHANNELS definition when DMA is disabled.
  sh: dmaengine support for SH7785
  sh: dmaengine support for sh7724.

With some of the cache rework an address aliasing optimization was added,
but this managed to fail on certain mappings resulting in pages with
PG_dcache_dirty set never writing back their dcache lines. This patch
reverts to the earlier behaviour of simply always writing back when the
dirty bit is set.
Signed-off-by: NMarkus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

o remove unused define
o add device name comment
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

ctrl_xxx() is an antiquated SH interface, while __raw_xxx is the standard
API that accomplishes the same thing. As such, this converts the
remaining sh-sci straggles over, which enables the driver to be wired up
for ARM SH-Mobile CPUs as well.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This establishes a sensible max baud rate for the earlyprintk cases where
the port's uartclk has not yet been determined.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

* 'i2c-fixes' of git://git.fluff.org/bjdooks/linux:
  i2c-omap: OMAP3: Fix I2C lockup during timeout/error cases
  i2c-omap: Don't write IE state in unidle if 0
  i2c-bfin-twi: fix CLKDIV calculation

Current OMAP3 I2C driver code does not follow the correct sequence for soft
reset. Due to this, lock up issues are reported during timeout/error cases.

This patch fixes above issue by disabling I2C controller as per OMAP3430 TRM
for soft reset. As per TRM, I2C controller needs to be disabled as a first
step during soft reset.

Here is correct soft reset sequence:
a. Ensure that the module is disabled
(clear the I2Ci.I2C_CON[15] I2C_EN bit to 0).
b. Set the I2Ci.I2C_SYSC[1] SRST bit to 1.
c. Enable the module by setting I2Ci.I2C_CON[15] I2C_EN bit to 1.
d. Check the I2Ci.I2C_SYSS[0] RDONE bit until it is set to 1 to
indicate the software reset is complete.

Tested on Zoom2, Zoom3, 3430SDP and 3630SDP
Signed-off-by: NManjunatha GK <manjugk@ti.com>
Signed-off-by: George, Harith<harith@ti.com>
Acked-by: Varadarajan, Charu Latha<charu@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Commit ef871432... (i2c-omap: OMAP3: PM: (re)init for every transfer
to support off-mode) introduced a change which make the dev->iestate
contents be written to the OMAP_I2C_IE_REG every time omap_i2c_unidle
is called.  Previously, the state was only written if it wasn't equal
to zero.

In omap_i2c_probe, omap_i2c_unidle() is called prior to omap_i2c_init(),
in which case dev->iestate has not yet been initialized and will be set
to zero.  Having this value written to the registers causes deadlock
while booting.

As such, this change restores the original functionality.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Calculation of the CLKDIV speed setting should be done using base 10 math
rather than base 2.  We also avoid exceeding the spec due to integer
truncation and a 50% duty cycle.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] use resource_size()
  [WATCHDOG] iTCO_wdt: add PCI ID for the Intel EP80579 (Tolapai) SoC

This reverts commit 9f15226e.  It's just
wrong, and broke resume for Rafael even on a non-AMD CPU.

As Rafael says:
 "... it causes microcode_init_cpu() to be called during resume even for
  CPUs for which there's no microcode to apply.  That, in turn, results
  in executing request_firmware() (on Intel CPUs at least) which doesn't
  work at this stage of resume (we have device interrupts disabled, I/O
  devices are still suspended and so on).

  If I'm not mistaken, the "if (uci->valid)" logic means "if that CPU is
  known to us" , so before commit 9f15226e microcode_resume_cpu() was
  called for all CPUs already in the system during suspend, which was
  the right thing to do.  The commit changed it so that the CPUs without
  microcode to apply are now treated as "unknown", which is not quite
  right.

  The problem this commit attempted to solve has to be handled
  differently."

Bisected-and -requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
  USB: Fix a bug on appledisplay.c regarding signedness
  USB: option: support hi speed for modem Haier CE100
  USB: audio gadget: free alsa devices when unloading
  USB: audio gadget: fix wTotalLength calculation
  usb: otg: isp1301_omap: fix compile error
  USB: musb: workaround Blackfin FIFO anomalies
  USB: musb: Fix array index out of bounds issue
  USB: musb: Fix null pointer dereference issue
  USB: musb: correct DMA address for tx
  USB: musb: gadget_ep0: avoid SetupEnd interrupt
  USB: musb: fix for crash in DM646x USB when (CPPI)DMA is enabled
  USB: musb: do not work if no gadget driver is loaded
  USB: musb: gadget: set otg tranceiver to idle when registering gadget
  USB: musb: Populate the VBUS GPIO with the correct GPIO number
  USB: musb: MAINTAINERS: Fix my tree's address
  USB: musb: fix compiling warning with min() macro
  USB: musb: move musb_remove to __exit
  USB: musb_gadget: fix kernel oops in txstate()
  USB: ftdi_sio: sort PID/VID entries in new ftdi_sio_ids.h header
  USB: ftdi_sio: isolate all device IDs to new ftdi_sio_ids.h header
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  devtmpfs: unlock mutex in case of string allocation error
  Driver core: export platform_device_register_data as a GPL symbol
  driver core: Prevent reference to freed memory on error path
  Driver-core: Fix bogus 0 error return in device_add()
  Driver core: driver_attribute parameters can often be const*
  Driver core: bin_attribute parameters can often be const*
  Driver core: device_attribute parameters can often be const*
  Doc/stable rules: add new cherry-pick logic
  vfs: get_sb_single() - do not pass options twice
  devtmpfs: Convert dirlock to a mutex

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging/vt66*: kconfig, depends on WLAN
  Staging: batman-adv: introduce missing kfree
  Staging: batman-adv: Add Kconfig dependancies on PROC_FS and PACKET.
  Staging: panel: Adjust range for PANEL_KEYPAD in Kconfig
  Staging: panel: Fix compilation error with custom lcd charset
  Staging: ramzswap: remove ARM specific d-cache hack
  Staging: rtl8192x: fix printk formats
  Staging: wlan-ng: fix Correct size given to memset
  staging: rtl8192su: add USB VID/PID for HWNUm-300
  staging: fix rtl8192su compilation errors with mac80211
  staging: fix rtl8192e compilation errors with mac80211
  Staging: fix rtl8187se compilation errors with mac80211
  Staging: rtl8192su: fix test for negative error in rtl8192_rx_isr()
  Staging: comedi: jr3_pci: Don't ioremap too much space. Check result.
  Staging: comedi: removed "depricated" from COMEDI_CB_BLOCK
  Staging: comedi: usbdux.c: fix locking up of the driver when the comedi ringbuffer runs empty
  Staging: dst: remove from the tree
  Staging: sm7xx: add a new framebuffer driver
  Staging: batman: fix debug Kconfig option

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  ocfs2: Set i_nlink properly during reflink.
  ocfs2: Add reflinked file's inode to inode hash eariler.
  ocfs2: refcounttree.c cleanup.
  ocfs2: Find proper end cpos for a leaf refcount block.

Use resource_size().
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Kevin Hilman <khilman@ti.deeprootsystems.com>
Cc: Ulrik Bech Hald <ubh@ti.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Vincent Sanders <support@simtec.co.uk>
Acked-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

add PCI ID for the Intel EP80579 (Tolapai) SoC
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

brightness status is reported by the Apple Cinema Displays as an
'unsigned char' (u8) value, but the code used 'char' instead.

Note that he driver was developed on the PowerPC architecture,
where the two types are synonymous, which is not always the case.

Fixed that.  Otherwise the driver will interpret brightness
levels > 127 as negative, and fail to load.
Signed-off-by: Npancho horrillo <pancho@pancho.name>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I made this patch for usbserial driver to add the support for EVDO modem
Haier CE100. The bugs report for this is here:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/490068

This patch based on these post:
http://blankblondtank.wordpress.com/2009/09/04/mengoptimalkan-koneksi-modem-haier-ce-100-cdma-di-linux/
http://tantos.web.id/blogs/how-to-internet-connection-using-cdma-evdo-modem-and-karmic-koala-ubuntu-9-10

I hope this patch can help other that have the Haier C100 modem, mostly in my country, Indonesia.
Signed-off-by: NDonny Kurnia <donnykurnia@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The wTotalLength should contain the sum of the interface and unit
descriptor sizes per the Audio Device Class specification 1.0.
Reported-by: NSergey Lapin <slapin@ossfans.org>
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

commit 91c8a5a9 broke
compilation of this driver after it introduced
otg_init() as a static inline in <linux/usb/otg.h>
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some of these workarounds are already in place, but labeled as affecting
all BF52x parts.  Since we have official anomaly numbers now, use those
defines.  And since writing to the FIFO has a similar hang issue as reading
from the FIFO, implement the workaround there too when necessary.
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the below array index out of bounds issue.

Buffer overflow, array index of 'aInfo' may be out of
bounds. Array 'aInfo' of size 78 may use index value(s) 6..84

The data stored in 'aInfo' array exceeds the array size of 78.

This patch increases the size of this array to hold the string
correctly without any memory corruption.

This issue was reported by Klockwork tool.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the following NULL pointer dereference issue.

Pointer 'request' returned from call to function 'next_request'
at line 748 may be NULL and may be dereferenced at line 792.

============
Code Snippet
============

748:  request = next_request(musb_ep);
785: if (dma && (csr & MUSB_RXCSR_DMAENAB)) {
	csr &= ~(MUSB_RXCSR_AUTOCLEAR
			| MUSB_RXCSR_DMAENAB
			| MUSB_RXCSR_DMAMODE);
	musb_writew(epio, MUSB_RXCSR,
		MUSB_RXCSR_P_WZC_BITS | csr);

792:	 request->actual += musb_ep->dma->actual_len;
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since a DMA transfer may need to be kicked off several times to complete,
the DMA start must include the length that has already been transferred.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Gadget stalling a zero-length SETUP request results in this error message:

SetupEnd came in a wrong ep0stage idle

In order to avoid it, always set the CSR0.DataEnd bit after detecting a zero-
length request.  Add the missing '\n' to the error message itself as well...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Race condition exists between the cppi_interrupt handler and
davinci_interrupt handler w.r.t completing a TX IO.  Since DM646x
has seperate DMA and USB endpoint interrupts cppi_interrupt handler
needs to hold the lock while operating on the endpoint.

Update over previous patch to avoid taking the lock if already
taken.  Tested on DM644x, DM355 and DM646x platforms.
Signed-off-by: NSwaminathan S <swami.iyer@ti.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On OTG and gadget-only configurations, we need a gadget driver
in order to work properly, so avoid changing operation modes
when there's no gadget driver loaded.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When registering gadget driver, the state of the transceiver
must be set from undefined (no gadget) to b_idle.

Module unload sets the transceiver state to undefined state.
After the first load/unload pair, the reset irq will be lost.
Signed-off-by: NArnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes a null-pointer dereference bug.
Signed-off-by: NSwaminathan S <swami.iyer@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The tree is now on a new address.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current musb gadget dma code produces the warning:
drivers/usb/musb/musb_gadget.c: In function 'txstate':
drivers/usb/musb/musb_gadget.c:312: warning: comparison of distinct
                                             pointer types lacks a cast

So switch to min_t(size_t, ...).
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

probe() already was on __init, so moving remove() to __exit.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 7723de7e (USB: musb_gadget: remove
pointless loop) included uncalled for (and incorrect) optimization that
might cause a kernel oops in txstate() -- undo it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a (almost) sort-only patch to sort FTDI device
product ID definitions in new ftdi_sio_ids.h header.

Advantage is that new device ID submissions will now have a specific (sorted)
position - less future merge conflicts.

Compile-tested, based on _current_ mainline git.
Minor checkpatch.pl warnings were eliminated whereever it made sense,
very minor text changes.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).

Compile-tested, based on latest mainline git.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix new kernel-doc warnings in usb core:

Warning(drivers/usb/core/usb.c:79): No description found for parameter 'config'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'iface_num'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'alt_num'
Warning(drivers/usb/core/hcd.c:1622): No description found for parameter 'udev'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Hi!

$ lsusb -v
Bus 001 Device 008: ID 05ac:921c Apple, Inc. 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0         8
  idVendor           0x05ac Apple, Inc.
  idProduct          0x921c 
  bcdDevice            1.15
  iManufacturer           1 
  iProduct                2 
  iSerial                 0 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           34
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                2mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              0 
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.11
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      92
         Report Descriptors: 
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              16
Signed-off-by: Npancho horrillo <pancho@pancho.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>