Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 13 8月, 2015 2 次提交
  3. 28 7月, 2015 1 次提交
    • M
      ACPI / PM: Use target_state to set the device power state · 71b65445
      由 Mika Westerberg 提交于 
      Commit 20dacb71 ("ACPI / PM: Rework device power management to follow
ACPI 6") changed the device power management to use D3hot if the device
in question does not have _PR3 method even if D3cold was requested by the
caller.

However, if the device has _PR3 device->power.state is also set to D3hot
instead of D3Cold after power resources have been turned off because
device->power.state will be assigned from "state" instead of
"target_state".

Next time the device is transitioned to D0, acpi_power_transition() will
find that the current power state of the device is D3hot instead of D3cold
which causes it to power down all resources required for the current
(wrong) state D3hot.

Below is a simplified ASL example of a real touch panel device which
triggers the problem:

  Scope (TPL1)
  {
      Name (_PR0, Package (1) { \_SB.PCI0.I2C1.PXTC })
      Name (_PR3, Package (1) { \_SB.PCI0.I2C1.PXTC })
      ...
  }

In both D0 and D3hot the same power resource is required. However, when
acpi_power_transition() turns off power resources required for D3hot (as
the device is transitioned to D0) it powers down PXTC which then makes the
device to lose its power.

Fix this by assigning "target_state" to the device power state instead of
"state" that is always D3hot even for devices with valid _PR3.

Fixes: 20dacb71 (ACPI / PM: Rework device power management to follow ACPI 6)
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
      71b65445
  5. 11 7月, 2015 2 次提交
  7. 10 7月, 2015 1 次提交
    • J
      ACPI / PCI: Fix regressions caused by resource_size_t overflow with 32-bit kernel · 1fb01ca9
      由 Jiang Liu 提交于 
      Zoltan Boszormenyi reported this regression:
  "There's a Realtek RTL8111/8168/8411 (PCI ID 10ec:8168, Subsystem ID
   1565:230e) network chip on the mainboard. After the r8169 driver loaded
   the IRQs in the machine went berserk. Keyboard keypressed arrived with
   considerable latency and duplicated, so no real work was possible.
   The machine responded to the power button but didn't actually power
   down. It just stuck at the powering down message. I had to press the
   power button for 4 seconds to power it down.

   The computer is a POS machine with a big battery inside. Because of this,
   either ACPI or the Realtek chip kept the bad state and after rebooting,
   the network chip didn't even show up in lspci. Not even the PXE ROM
   announced itself during boot. I had to disconnect the battery to beat
   some sense back to the computer.

   The regression happens with 4.0.5, 4.1.0-rc8 and 4.1.0-final. 3.18.16 was
   good."

The regression is caused by commit 593669c2 (x86/PCI/ACPI: Use common
ACPI resource interfaces to simplify implementation). Since commit
593669c2, x86 PCI ACPI host bridge driver validates ACPI resources by
first converting an ACPI resource to a 'struct resource' structure and
then applying checks against the converted resource structure. The 'start'
and 'end' fields in 'struct resource' are defined to be type of
resource_size_t, which may be 32 bits or 64 bits depending on
CONFIG_PHYS_ADDR_T_64BIT.

This may cause incorrect resource validation results with 32-bit kernels
because 64-bit ACPI resource descriptors may get truncated when converting
to 32-bit 'start' and 'end' fields in 'struct resource'. It eventually
affects PCI resource allocation subsystem and makes some PCI devices and
the system behave abnormally due to incorrect resource assignment.

So enhance the ACPI resource parsing interfaces to ignore ACPI resource
descriptors with address/offset above 4G when running in 32-bit mode.

With the fix applied, the behavior of the machine was restored to how
3.18.16 worked, i.e. the memory range that is over 4GB is ignored again,
and lspci -vvxxx shows that everything is at the same memory window as
they were with 3.18.16.
Reported-and-tested-by: NBoszormenyi Zoltan <zboszor@pr.hu>
Fixes: 593669c2 (x86/PCI/ACPI: Use common ACPI resource interfaces to simplify implementation)
Signed-off-by: NJiang Liu <jiang.liu@linux.intel.com>
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
      1fb01ca9
  9. 07 7月, 2015 3 次提交
    • S
      ACPI / scan: Add support for ACPI _CLS device matching · 26095a01
      由 Suthikulpanit, Suravee 提交于 
      Device drivers typically use ACPI _HIDs/_CIDs listed in struct device_driver
acpi_match_table to match devices. However, for generic drivers, we do not
want to list _HID for all supported devices. Also, certain classes of devices
do not have _CID (e.g. SATA, USB). Instead, we can leverage ACPI _CLS,
which specifies PCI-defined class code (i.e. base-class, subclass and
programming interface). This patch adds support for matching ACPI devices using
the _CLS method.

To support loadable module, current design uses _HID or _CID to match device's
modalias. With the new way of matching with _CLS this would requires modification
to the current ACPI modalias key to include _CLS. This patch appends PCI-defined
class-code to the existing ACPI modalias as following.

    acpi:<HID>:<CID1>:<CID2>:..:<CIDn>:<bbsspp>:
E.g:
    # cat /sys/devices/platform/AMDI0600:00/modalias
    acpi:AMDI0600:010601:

where bb is th base-class code, ss is te sub-class code, and pp is the
programming interface code

Since there would not be _HID/_CID in the ACPI matching table of the driver,
this patch adds a field to acpi_device_id to specify the matching _CLS.

    static const struct acpi_device_id ahci_acpi_match[] = {
        { ACPI_DEVICE_CLASS(PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff) },
        {},
    };

In this case, the corresponded entry in modules.alias file would be:

    alias acpi*:010601:* ahci_platform
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NSuravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
      26095a01
    • R
      ACPI / LPSS: Fix up acpi_lpss_create_device() · d3e13ff3
      由 Rafael J. Wysocki 提交于 
      Fix a return value (which should be a negative error code) and a
memory leak (the list allocated by acpi_dev_get_resources() needs
to be freed on ioremap() errors too) in acpi_lpss_create_device()
introduced by commit 4483d59e 'ACPI / LPSS: check the result
of ioremap()'.

Fixes: 4483d59e 'ACPI / LPSS: check the result of ioremap()'
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
      d3e13ff3
    • R
      ACPI / PNP: Reserve ACPI resources at the fs_initcall_sync stage · 0294112e
      由 Rafael J. Wysocki 提交于 
      This effectively reverts the following three commits:

 7bc10388 ACPI / resources: free memory on error in add_region_before()
 0f1b414d ACPI / PNP: Avoid conflicting resource reservations
 b9a5e5e1 ACPI / init: Fix the ordering of acpi_reserve_resources()

(commit b9a5e5e1 introduced regressions some of which, but not
all, were addressed by commit 0f1b414d and commit 7bc10388
was a fixup on top of the latter) and causes ACPI fixed hardware
resources to be reserved at the fs_initcall_sync stage of system
initialization.

The story is as follows.  First, a boot regression was reported due
to an apparent resource reservation ordering change after a commit
that shouldn't lead to such changes.  Investigation led to the
conclusion that the problem happened because acpi_reserve_resources()
was executed at the device_initcall() stage of system initialization
which wasn't strictly ordered with respect to driver initialization
(and with respect to the initialization of the pcieport driver in
particular), so a random change causing the device initcalls to be
run in a different order might break things.

The response to that was to attempt to run acpi_reserve_resources()
as soon as we knew that ACPI would be in use (commit b9a5e5e1).
However, that turned out to be too early, because it caused resource
reservations made by the PNP system driver to fail on at least one
system and that failure was addressed by commit 0f1b414d.

That fix still turned out to be insufficient, though, because
calling acpi_reserve_resources() before the fs_initcall stage of
system initialization caused a boot regression to happen on the
eCAFE EC-800-H20G/S netbook.  That meant that we only could call
acpi_reserve_resources() at the fs_initcall initialization stage
or later, but then we might just as well call it after the PNP
initalization in which case commit 0f1b414d wouldn't be
necessary any more.

For this reason, the changes made by commit 0f1b414d are reverted
(along with a memory leak fixup on top of that commit), the changes
made by commit b9a5e5e1 that went too far are reverted too and
acpi_reserve_resources() is changed into fs_initcall_sync, which
will cause it to be executed after the PNP subsystem initialization
(which is an fs_initcall) and before device initcalls (including
the pcieport driver initialization) which should avoid the initial
issue.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=100581
Link: http://marc.info/?t=143092384600002&r=1&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831
Link: http://marc.info/?t=143389402600001&r=1&w=2
Fixes: b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()"
Reported-by: NRoland Dreier <roland@purestorage.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
      0294112e
  11. 03 7月, 2015 2 次提交
  13. 02 7月, 2015 13 次提交
  15. 01 7月, 2015 1 次提交
  17. 26 6月, 2015 7 次提交
    • T
      libnvdimm: Add sysfs numa_node to NVDIMM devices · 74ae66c3
      由 Toshi Kani 提交于 
      Add support of sysfs 'numa_node' to I/O-related NVDIMM devices
under /sys/bus/nd/devices, regionN, namespaceN.0, and bttN.x.

An example of numa_node values on a 2-socket system with a single
NVDIMM range on each socket is shown below.
  /sys/bus/nd/devices
  |-- btt0.0/numa_node:0
  |-- btt1.0/numa_node:1
  |-- btt1.1/numa_node:1
  |-- namespace0.0/numa_node:0
  |-- namespace1.0/numa_node:1
  |-- region0/numa_node:0
  |-- region1/numa_node:1

These numa_node files are then linked under the block class of
their device names.
  /sys/class/block/pmem0/device/numa_node:0
  /sys/class/block/pmem1s/device/numa_node:1

This enables numactl(8) to accept 'block:' and 'file:' paths of
pmem and btt devices as shown in the examples below.
  numactl --preferred block:pmem0 --show
  numactl --preferred file:/dev/pmem1s --show
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      74ae66c3
    • T
      libnvdimm: Set numa_node to NVDIMM devices · 41d7a6d6
      由 Toshi Kani 提交于 
      ACPI NFIT table has System Physical Address Range Structure entries that
describe a proximity ID of each range when ACPI_NFIT_PROXIMITY_VALID is
set in the flags.

Change acpi_nfit_register_region() to map a proximity ID to its node ID,
and set it to a new numa_node field of nd_region_desc, which is then
conveyed to the nd_region device.

The device core arranges for btt and namespace devices to inherit their
node from their parent region.
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
[djbw: move set_dev_node() from region.c to bus.c]
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      41d7a6d6
    • T
      acpi: Add acpi_map_pxm_to_online_node() · 99759869
      由 Toshi Kani 提交于 
      The kernel initializes CPU & memory's NUMA topology from ACPI
SRAT table.  Some other ACPI tables, such as NFIT and DMAR, also
contain proximity IDs for their device's NUMA topology.  This
information can be used to improve performance of these devices.

This patch introduces acpi_map_pxm_to_online_node(), which is
similar to acpi_map_pxm_to_node(), but always returns an online
node.  When the mapped node from a given proximity ID is offline,
it looks up the node distance table and returns the nearest
online node.

ACPI device drivers, which are called after the NUMA initialization
has completed in the kernel, can call this interface to obtain their
device NUMA topology from ACPI tables.  Such drivers do not have to
deal with offline nodes.  A node may be offline when a device
proximity ID is unique, SRAT memory entry does not exist, or NUMA is
disabled, ex. "numa=off" on x86.

This patch also moves the pxm range check from acpi_get_node() to
acpi_map_pxm_to_node().
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com&gt;>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      99759869
    • D
      libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only · 58138820
      由 Dan Williams 提交于 
      Upon detection of an unarmed dimm in a region, arrange for descendant
BTT, PMEM, or BLK instances to be read-only.  A dimm is primarily marked
"unarmed" via flags passed by platform firmware (NFIT).

The flags in the NFIT memory device sub-structure indicate the state of
the data on the nvdimm relative to its energy source or last "flush to
persistence".  For the most part there is nothing the driver can do but
advertise the state of these flags in sysfs and emit a message if
firmware indicates that the contents of the device may be corrupted.
However, for the case of ACPI_NFIT_MEM_ARMED, the driver can arrange for
the block devices incorporating that nvdimm to be marked read-only.
This is a safe default as the data is still available and new writes are
held off until the administrator either forces read-write mode, or the
energy source becomes armed.

A 'read_only' attribute is added to REGION devices to allow for
overriding the default read-only policy of all descendant block devices.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      58138820
    • D
      tools/testing/nvdimm: libnvdimm unit test infrastructure · 6bc75619
      由 Dan Williams 提交于 
      'libnvdimm' is the first driver sub-system in the kernel to implement
mocking for unit test coverage.  The nfit_test module gets built as an
external module and arranges for external module replacements of nfit,
libnvdimm, nd_pmem, and nd_blk.  These replacements use the linker
--wrap option to redirect calls to ioremap() + request_mem_region() to
custom defined unit test resources.  The end result is a fully
functional nvdimm_bus, as far as userspace is concerned, but with the
capability to perform otherwise destructive tests on emulated resources.

Q: Why not use QEMU for this emulation?
QEMU is not suitable for unit testing.  QEMU's role is to faithfully
emulate the platform.  A unit test's role is to unfaithfully implement
the platform with the goal of triggering bugs in the corners of the
sub-system implementation.  As bugs are discovered in platforms, or the
sub-system itself, the unit tests are extended to backstop a fix with a
reproducer unit test.

Another problem with QEMU is that it would require coordination of 3
software projects instead of 2 (kernel + libndctl [1]) to maintain and
execute the tests.  The chances for bit rot and the difficulty of
getting the tests running goes up non-linearly the more components
involved.


Q: Why submit this to the kernel tree instead of external modules in
   libndctl?
Simple, to alleviate the same risk that out-of-tree external modules
face.  Updates to drivers/nvdimm/ can be immediately evaluated to see if
they have any impact on tools/testing/nvdimm/.


Q: What are the negative implications of merging this?
It is a unique maintenance burden because the purpose of mocking an
interface to enable a unit test is to purposefully short circuit the
semantics of a routine to enable testing.  For example
__wrap_ioremap_cache() fakes the pmem driver into "ioremap()'ing" a test
resource buffer allocated by dma_alloc_coherent().  The future
maintenance burden hits when someone changes the semantics of
ioremap_cache() and wonders what the implications are for the unit test.

[1]: https://github.com/pmem/ndctl

Cc: <linux-acpi@vger.kernel.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      6bc75619
    • R
      libnvdimm, nfit, nd_blk: driver for BLK-mode access persistent memory · 047fc8a1
      由 Ross Zwisler 提交于 
      The libnvdimm implementation handles allocating dimm address space (DPA)
between PMEM and BLK mode interfaces.  After DPA has been allocated from
a BLK-region to a BLK-namespace the nd_blk driver attaches to handle I/O
as a struct bio based block device. Unlike PMEM, BLK is required to
handle platform specific details like mmio register formats and memory
controller interleave.  For this reason the libnvdimm generic nd_blk
driver calls back into the bus provider to carry out the I/O.

This initial implementation handles the BLK interface defined by the
ACPI 6 NFIT [1] and the NVDIMM DSM Interface Example [2] composed from
DCR (dimm control region), BDW (block data window), IDT (interleave
descriptor) NFIT structures and the hardware register format.
[1]: http://www.uefi.org/sites/default/files/resources/ACPI_6.0.pdf
[2]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf

Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boaz Harrosh <boaz@plexistor.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      047fc8a1
    • V
      nd_btt: atomic sector updates · 5212e11f
      由 Vishal Verma 提交于 
      BTT stands for Block Translation Table, and is a way to provide power
fail sector atomicity semantics for block devices that have the ability
to perform byte granularity IO. It relies on the capability of libnvdimm
namespace devices to do byte aligned IO.

The BTT works as a stacked blocked device, and reserves a chunk of space
from the backing device for its accounting metadata. It is a bio-based
driver because all IO is done synchronously, and there is no queuing or
asynchronous completions at either the device or the driver level.

The BTT uses 'lanes' to index into various 'on-disk' data structures,
and lanes also act as a synchronization mechanism in case there are more
CPUs than available lanes. We did a comparison between two lane lock
strategies - first where we kept an atomic counter around that tracked
which was the last lane that was used, and 'our' lane was determined by
atomically incrementing that. That way, for the nr_cpus > nr_lanes case,
theoretically, no CPU would be blocked waiting for a lane. The other
strategy was to use the cpu number we're scheduled on to and hash it to
a lane number. Theoretically, this could block an IO that could've
otherwise run using a different, free lane. But some fio workloads
showed that the direct cpu -> lane hash performed faster than tracking
'last lane' - my reasoning is the cache thrash caused by moving the
atomic variable made that approach slower than simply waiting out the
in-progress IO. This supports the conclusion that the driver can be a
very simple bio-based one that does synchronous IOs instead of queuing.

Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boaz Harrosh <boaz@plexistor.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Neil Brown <neilb@suse.de>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
[jmoyer: fix nmi watchdog timeout in btt_map_init]
[jmoyer: move btt initialization to module load path]
[jmoyer: fix memory leak in the btt initialization path]
[jmoyer: Don't overwrite corrupted arenas]
Signed-off-by: NVishal Verma <vishal.l.verma@linux.intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      5212e11f
  19. 25 6月, 2015 8 次提交
    • D
      libnvdimm, nfit: add interleave-set state-tracking infrastructure · eaf96153
      由 Dan Williams 提交于 
      On platforms that have firmware support for reading/writing per-dimm
label space, a portion of the dimm may be accessible via an interleave
set PMEM mapping in addition to the dimm's BLK (block-data-window
aperture(s)) interface.  A label, stored in a "configuration data
region" on the dimm, disambiguates which dimm addresses are accessed
through which exclusive interface.

Add infrastructure that allows the kernel to block modifications to a
label in the set while any member dimm is active.  Note that this is
meant only for enforcing "no modifications of active labels" via the
coarse ioctl command.  Adding/deleting namespaces from an active
interleave set is always possible via sysfs.

Another aspect of tracking interleave sets is tracking their integrity
when DIMMs in a set are physically re-ordered.  For this purpose we
generate an "interleave-set cookie" that can be recorded in a label and
validated against the current configuration.  It is the bus provider
implementation's responsibility to calculate the interleave set cookie
and attach it to a given region.

Cc: Neil Brown <neilb@suse.de>
Cc: <linux-acpi@vger.kernel.org>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      eaf96153
    • D
      libnvdimm: support for legacy (non-aliasing) nvdimms · 3d88002e
      由 Dan Williams 提交于 
      The libnvdimm region driver is an intermediary driver that translates
non-volatile "region"s into "namespace" sub-devices that are surfaced by
persistent memory block-device drivers (PMEM and BLK).

ACPI 6 introduces the concept that a given nvdimm may simultaneously
offer multiple access modes to its media through direct PMEM load/store
access, or windowed BLK mode.  Existing nvdimms mostly implement a PMEM
interface, some offer a BLK-like mode, but never both as ACPI 6 defines.
If an nvdimm is single interfaced, then there is no need for dimm
metadata labels.  For these devices we can take the region boundaries
directly to create a child namespace device (nd_namespace_io).
Acked-by: NChristoph Hellwig <hch@lst.de>
Tested-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      3d88002e
    • D
      libnvdimm, nfit: regions (block-data-window, persistent memory, volatile memory) · 1f7df6f8
      由 Dan Williams 提交于 
      A "region" device represents the maximum capacity of a BLK range (mmio
block-data-window(s)), or a PMEM range (DAX-capable persistent memory or
volatile memory), without regard for aliasing.  Aliasing, in the
dimm-local address space (DPA), is resolved by metadata on a dimm to
designate which exclusive interface will access the aliased DPA ranges.
Support for the per-dimm metadata/label arrvies is in a subsequent
patch.

The name format of "region" devices is "regionN" where, like dimms, N is
a global ida index assigned at discovery time.  This id is not reliable
across reboots nor in the presence of hotplug.  Look to attributes of
the region or static id-data of the sub-namespace to generate a
persistent name.  However, if the platform configuration does not change
it is reasonable to expect the same region id to be assigned at the next
boot.

"region"s have 2 generic attributes "size", and "mapping"s where:
- size: the BLK accessible capacity or the span of the
  system physical address range in the case of PMEM.

- mappingN: a tuple describing a dimm's contribution to the region's
  capacity in the format (<nmemX>,<dpa>,<size>).  For a PMEM-region
  there will be at least one mapping per dimm in the interleave set.  For
  a BLK-region there is only "mapping0" listing the starting DPA of the
  BLK-region and the available DPA capacity of that space (matches "size"
  above).

The max number of mappings per "region" is hard coded per the
constraints of sysfs attribute groups.  That said the number of mappings
per region should never exceed the maximum number of possible dimms in
the system.  If the current number turns out to not be enough then the
"mappings" attribute clarifies how many there are supposed to be. "32
should be enough for anybody...".

Cc: Neil Brown <neilb@suse.de>
Cc: <linux-acpi@vger.kernel.org>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      1f7df6f8
    • D
      libnvdimm, nvdimm: dimm driver and base libnvdimm device-driver infrastructure · 4d88a97a
      由 Dan Williams 提交于 
      * Implement the device-model infrastructure for loading modules and
  attaching drivers to nvdimm devices.  This is a simple association of a
  nd-device-type number with a driver that has a bitmask of supported
  device types.  To facilitate userspace bind/unbind operations 'modalias'
  and 'devtype', that also appear in the uevent, are added as generic
  sysfs attributes for all nvdimm devices.  The reason for the device-type
  number is to support sub-types within a given parent devtype, be it a
  vendor-specific sub-type or otherwise.

* The first consumer of this infrastructure is the driver
  for dimm devices.  It simply uses control messages to retrieve and
  store the configuration-data image (label set) from each dimm.

Note: nd_device_register() arranges for asynchronous registration of
      nvdimm bus devices by default.

Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Neil Brown <neilb@suse.de>
Acked-by: NChristoph Hellwig <hch@lst.de>
Tested-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      4d88a97a
    • D
      libnvdimm: control (ioctl) messages for nvdimm_bus and nvdimm devices · 62232e45
      由 Dan Williams 提交于 
      Most discovery/configuration of the nvdimm-subsystem is done via sysfs
attributes.  However, some nvdimm_bus instances, particularly the
ACPI.NFIT bus, define a small set of messages that can be passed to the
platform.  For convenience we derive the initial libnvdimm-ioctl command
formats directly from the NFIT DSM Interface Example formats.

    ND_CMD_SMART: media health and diagnostics
    ND_CMD_GET_CONFIG_SIZE: size of the label space
    ND_CMD_GET_CONFIG_DATA: read label space
    ND_CMD_SET_CONFIG_DATA: write label space
    ND_CMD_VENDOR: vendor-specific command passthrough
    ND_CMD_ARS_CAP: report address-range-scrubbing capabilities
    ND_CMD_ARS_START: initiate scrubbing
    ND_CMD_ARS_STATUS: report on scrubbing state
    ND_CMD_SMART_THRESHOLD: configure alarm thresholds for smart events

If a platform later defines different commands than this set it is
straightforward to extend support to those formats.

Most of the commands target a specific dimm.  However, the
address-range-scrubbing commands target the bus.  The 'commands'
attribute in sysfs of an nvdimm_bus, or nvdimm, enumerate the supported
commands for that object.

Cc: <linux-acpi@vger.kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: NNicholas Moulin <nicholas.w.moulin@linux.intel.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      62232e45
    • D
      libnvdimm, nfit: dimm/memory-devices · e6dfb2de
      由 Dan Williams 提交于 
      Enable nvdimm devices to be registered on a nvdimm_bus.  The kernel
assigned device id for nvdimm devicesis dynamic.  If userspace needs a
more static identifier it should consult a provider-specific attribute.
In the case where NFIT is the provider, the 'nmemX/nfit/handle' or
'nmemX/nfit/serial' attributes may be used for this purpose.

Cc: Neil Brown <neilb@suse.de>
Cc: <linux-acpi@vger.kernel.org>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      e6dfb2de
    • D
      libnvdimm: control character device and nvdimm_bus sysfs attributes · 45def22c
      由 Dan Williams 提交于 
      The control device for a nvdimm_bus is registered as an "nd" class
device.  The expectation is that there will usually only be one "nd" bus
registered under /sys/class/nd.  However, we allow for the possibility
of multiple buses and they will listed in discovery order as
ndctl0...ndctlN.  This character device hosts the ioctl for passing
control messages.  The initial command set has a 1:1 correlation with
the commands listed in the by the "NFIT DSM Example" document [1], but
this scheme is extensible to future command sets.

Note, nd_ioctl() and the backing ->ndctl() implementation are defined in
a subsequent patch.  This is simply the initial registrations and sysfs
attributes.

[1]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf

Cc: Neil Brown <neilb@suse.de>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: <linux-acpi@vger.kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      45def22c
    • D
      libnvdimm, nfit: initial libnvdimm infrastructure and NFIT support · b94d5230
      由 Dan Williams 提交于 
      A struct nvdimm_bus is the anchor device for registering nvdimm
resources and interfaces, for example, a character control device,
nvdimm devices, and I/O region devices.  The ACPI NFIT (NVDIMM Firmware
Interface Table) is one possible platform description for such
non-volatile memory resources in a system.  The nfit.ko driver attaches
to the "ACPI0012" device that indicates the presence of the NFIT and
parses the table to register a struct nvdimm_bus instance.

Cc: <linux-acpi@vger.kernel.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NJeff Moyer <jmoyer@redhat.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      b94d5230