We can apperently miss them, but breaking the entire driver hampers
testing. So bail out after one minute, our customerary "this is a lost
cause" timeout.

References: https://bugs.freedesktop.org/show_bug.cgi?id=78383Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So far we used the wrong opcodes to access the DSI registers, so the
register writes during DSI programming didn't actually succeed and left
the registers unchanged. This wasn't a problem for the initial modeset,
where the BIOS-programmed values happened to work, but after resuming
from s0ix these registers are reset and failing to program them results
in a blank screen.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These opcodes are not specific for an endpoint, but are the same for all
endpoints. So rename them accordingly, using the name the VLV2 sideband
HAS uses. Also move the macros to the .c file, since they aren't used
anywhere else.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fixed several switch statements, curly braces, dereference operators
and keywords.
Signed-off-by: NRobin Schroer <sulamiification@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Our two ->crtc_mode_set callbacks really don't care whether the fb is
pinned and set up already or not - all the state computation and
handling which originally looked at the framebuffer is already using
the indirection through the pipe configuration.

Eventually we want to move this up a bit more, but as long as the crtc
mode_set callback still exists (and as long as we don't need to pin an
entire pile of planes due to atomic modesets) there's not much point
in it. So I'll let this be for now.

v2: Don't forget about haswell ...
Reviewed-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A lot of the code in set_base is uncessary when the crtc is off, so we
can get rid of it all. Also, we don't need to call the fbc/psr update
functions since the crtc enable/disable hooks do that already.

The only things we really need are:
- Pin the new framebuffer and potentially unpin the old framebuffer
  (if the crtc has been on and we only change the configuration).
- Update the plane registers.

The first step will move out of platform code with the very next
patch.

v2: Don't forget about haswell ...
Reviewed-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

My plan here is to split up set_base into a prepare step, which does
the pinning, and a commit stage, which updates the hw state. Eventually
we should be able to move the prepare step at the beginning of any
atomic update. For now I only want to move the commit step into the
crtc_enable callbacks.

As a prep step sprinkle intel_edp_psr_update all over the place so
that we don't have to concern ourselves with that in the commit step.

v2: Rebase on top of Ville's enable/disable functions for all planes.

v3: Rebase more.

Reviewed-by: Akash Goel <akash.goel@intel.com> (v2)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just for consistency, this patch won't fix anything really.

v2: Rebase over all the recent plane enabling shuffling.

Reviewed-by: Akash Goel <akash.goel@intel.com> (v1)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Way back we've used this to reject framebuffers with unsupported
pixel formats. But since the modesetting reorg with the compute
config stage we reject those much earlier and just BUG() in this
callback. So switch to a void return type.
Reviewed-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

More fallout from

commit c8725f3d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Mon Mar 17 12:21:55 2014 +0000

    drm/i915: Do not call retire_requests from wait_for_rendering

is that we can completely fill all of memory using small objects, such
that we exhaust the filp space, and spend all of our time evicting
objects from the aperture. As such, we never fill the ring, and never
trigger the last resort flushing in

commit 1cf0ba14
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Mon May 5 09:07:33 2014 +0100

    drm/i915: Flush request queue when waiting for ring space

and so all the requests are left active and the objects keep that last
active reference. Eventually the system comes to a halt as it runs out
of memory.

The impact is mainly limited to test cases as regular userspace will
trigger retirement by manually checking whether an object is active.

Testcase: igt/gem_lut_handle
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78724Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NGuo Jinxian <jinxianx.guo@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since commit 691e6415
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Wed Apr 9 09:07:36 2014 +0100

    drm/i915: Always use kref tracking for all contexts.

we have contexts everywhere, and so we must be careful to distinguish
fake contexts, which do not have an associated bo, and real ones, which
do. In particular, we now need to be careful not to dereference NULL
pointers.

This is one such example, as the commit highlighted above failed to move
the unpinning of the default ctx object into the real-context-only
branch.
Reported-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78792Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some platforms have a shared error interrupt, so if FIFO underrun
reporting gets disabled for one pipe/transcoder it gets disabled
for all pipes/transcoders.

When we disable FIFO underrun reporting we check whether the
interrupt was enabled or not. If it wasn't we might have missed
an underrun and we perform one last check right there. Currently
we print a debug message when an underrun is detect using this
mechanism. Promote the message to DRM_ERROR() to match the other
underrun error messages.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By exporting the ability to map user address and inserting PTEs
representing their backing pages into the GTT, we can exploit UMA in order
to utilize normal application data as a texture source or even as a
render target (depending upon the capabilities of the chipset). This has
a number of uses, with zero-copy downloads to the GPU and efficient
readback making the intermixed streaming of CPU and GPU operations
fairly efficient. This ability has many widespread implications from
faster rendering of client-side software rasterisers (chromium),
mitigation of stalls due to read back (firefox) and to faster pipelining
of texture data (such as pixel buffer objects in GL or data blobs in CL).

v2: Compile with CONFIG_MMU_NOTIFIER
v3: We can sleep while performing invalidate-range, which we can utilise
to drop our page references prior to the kernel manipulating the vma
(for either discard or cloning) and so protect normal users.
v4: Only run the invalidate notifier if the range intercepts the bo.
v5: Prevent userspace from attempting to GTT mmap non-page aligned buffers
v6: Recheck after reacquire mutex for lost mmu.
v7: Fix implicit padding of ioctl struct by rounding to next 64bit boundary.
v8: Fix rebasing error after forwarding porting the back port.
v9: Limit the userptr to page aligned entries. We now expect userspace
    to handle all the offset-in-page adjustments itself.
v10: Prevent vma from being copied across fork to avoid issues with cow.
v11: Drop vma behaviour changes -- locking is nigh on impossible.
     Use a worker to load user pages to avoid lock inversions.
v12: Use get_task_mm()/mmput() for correct refcounting of mm.
v13: Use a worker to release the mmu_notifier to avoid lock inversion
v14: Decouple mmu_notifier from struct_mutex using a custom mmu_notifer
     with its own locking and tree of objects for each mm/mmu_notifier.
v15: Prevent overlapping userptr objects, and invalidate all objects
     within the mmu_notifier range
v16: Fix a typo for iterating over multiple objects in the range and
     rearrange error path to destroy the mmu_notifier locklessly.
     Also close a race between invalidate_range and the get_pages_worker.
v17: Close a race between get_pages_worker/invalidate_range and fresh
     allocations of the same userptr range - and notice that
     struct_mutex was presumed to be held when during creation it wasn't.
v18: Sigh. Fix the refactor of st_set_pages() to allocate enough memory
     for the struct sg_table and to clear it before reporting an error.
v19: Always error out on read-only userptr requests as we don't have the
     hardware infrastructure to support them at the moment.
v20: Refuse to implement read-only support until we have the required
     infrastructure - but reserve the bit in flags for future use.
v21: use_mm() is not required for get_user_pages(). It is only meant to
     be used to fix up the kernel thread's current->mm for use with
     copy_user().
v22: Use sg_alloc_table_from_pages for that chunky feeling
v23: Export a function for sanity checking dma-buf rather than encode
     userptr details elsewhere, and clean up comments based on
     suggestions by Bradley.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Gong, Zhipeng" <zhipeng.gong@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Cc: "Volkin, Bradley D" <bradley.d.volkin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: NBrad Volkin <bradley.d.volkin@intel.com>
[danvet: Frob ioctl allocation to pick the next one - will cause a bit
of fuss with create2 apparently, but such are the rules.]
[danvet2: oops, forgot to git add after manual patch application]
[danvet3: Appease sparse.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Bit 31 in GEN6_PMINTRMSK is not an interrupt disable bit with gen8.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise, we do a NULL pointer dereference.

I've seen this happen while handling an error in
i915_gem_object_pin_to_display_plane():

If i915_gem_object_set_cache_level() fails, we call is_pin_display()
to handle the error. At this point, the object is still not pinned
to GGTT and maybe not even bound, so we have to check before we
dereference its GGTT vma.

The IGT kms_flip/bo-too-big tests for this bug.

v2: Chris Wilson says restoring the old value is easier, but that
is_pin_display is useful as a theory of operation. Take the solomonic
decision: at least this way is_pin_display is a little more robust
(until Chris can kill it off).

v3: Chris suggests the WARN in i915_gem_obj_to_ggtt has outlived its
usefulness: add a reminder to remove it.

Issue: VIZ-3772
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Testcase: igt/kms_flip/bo-too-big
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

All the callbacks are gone now.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Looking at our current dsi driver I note that:
- We don't have any slave driver right now.
- There's zero support for the hardware state readout and cross check
  code.
- All the modeset state seems to be tracked in the intel_dsi structure
  instead of the pipe config.

Given all that I can't properly audit the dsi ->mode_set callback. So
just do it as the first thing in the ->pre_pll_enable hook and hope
for the best.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A bit more care required here since there are some very few things
between the call to encoder->mode_set and encoder->pre_enable. But
they're either book-keeping or only matter for the vga port on the
pch. So of no concern.

Note that with the new sequence we write the infoframes after
selecting the clock source, but that shouldn't matter. I've simply
opted for this to have simpler code.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

All the hard work was already done, only thing left to do is remove
the empty callback. And a now rather misleading comment I've spotted
while reading through code.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Similar to dp the only thing we do is call intel_write_eld and prepare
a bit of state for the enable hooks. The only difference is that we
write that to the hardware instead of keeping track of it somewhere in
software.

Still we can just move all this to the very first enable hook.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Those functions are only used on vlv platforms, so no need to check.
Especially if we're not too consistent about it.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With all the preceding refactoring the dp mode_set callback only
computes a bit of state (all derived from the pipe config) and also
writes the eld. As long as we do that before we enable the audio bit
or depend upon the correct value in intel_dp->DP we'll be fine.

No other hw state is touched.

We therefore only need to check that clearing intel_dp->DP is save.
Which it is since when we re-enable we already mask out all the bits
the link training code sets. And we need to keep on doing that so that
the re-train loop walking over pre-emph/voltage-swing values still
works properly.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Only ilk/snb/ivb need the port A pll setup, so move it to the
pre_enable hook for those platforms. We can savely do this since on
those platforms there's nothing that touches the hardware between the
encoder->mode_set and the encoder->pre_enable calls.

Also add a comment that port A is ilk+ only.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Including state readout and cross-checking. This allows us to get rid
of crtc->eld_vld on hsw+. It also means that fastboot will be unhappy
if the BIOS hasn't set up the audio routing like we want it too.

Wrt fastboot and external screens I see a few options:
- Don't.
- Try to fix up eld, infoframes and audio settings after the fact. But
  that means some pretty extensive reworking of our code which
  currently does all this while the pipe/port is still off.

I won't bother with converting SDVO over to this because the audio
support for SDVO is very lacking:
- We don't update the eld.
- We don't update the audio state on the sdvo encoder.
- We don't check whether the platform can even feed audio to the sdvo
  encoder.

I've converted hdmi, dp & ddi all in one go since ddi needs both hdmi
and dp converted and so doing it step-by-step would have required a
few intermediate hacks.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There's no need to check whether audio is enabled (which for ddi ports
is done through the crtc->eld_vld flag) since at the cost of a
potentially unecessary register rmw cycle we can unconditionally do
this.

Note that the edp check is just paranoia since we won't ever call the
write_eld function for an edp panel.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This way we can rely on the state cross-checker to have a bit
assurance that we'll get it right.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

At least on those platforms which have a simple bit and don't rely
on the fully programmable CSC unit to do this.

Note that with the current code this includes CHV, but I guess that
platform will match BYT.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We in the pre_enable hook we should only rely on the pipe config and
not on some other state set through properties or detect functions.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Also add state readout and cross-check support. The only invasive change
is wiring up the new flag to the ->set_infoframes callbacks.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For compliance we really should be sending NULL infoframes always
when we detect a hdmi capable monitor. Also remove the now redudant
setting for the has_audio case and enforce that audio is only
possible with a hdmi sink.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Everything should be in place so enable rc6/rps for bdw.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

by correctly displaying result and requested.
Suggested-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In BDW, Apart from unmasking up/down threshold interrupts. we need
to umask bit 32 of PM_INTRMASK to route interrupts to target via Display
Interface.

v2: Add (1<<31) mask (Ville)

v3: Add Gen check for the mask (ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Almost all of it is reusable from the existing code. The primary
difference is we need to do even less in the interrupt handler, since
interrupts are not shared in the same way.

The patch is mostly a copy-paste of the existing snb+ code, with updates
to the relevant parts requiring changes to the interrupt handling. As
such it /should/ be relatively trivial. It's highly likely that I missed
some places where I need a gen8 version of the PM interrupts, but it has
become invisible to me by now.

This patch could probably be split into adding the new functions,
followed by actually handling the interrupts. Since the code is
currently disabled (and broken) I think the patch stands better by
itself.

v2: Move the commit about not touching the ringbuffer interrupt to the
snb_* function where it belongs (Rodrigo)

v3: Rebased on Paulo's runtime PM changes

v4: Not well validated, but rebase on
commit 730488b2
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Fri Mar 7 20:12:32 2014 -0300

    drm/i915: kill dev_priv->pm.regsave

v5: Rebased on latest code base. (Deepak)

v6: Remove conflict markers, Unnecessary empty line and use right
IIR interrupt (Ville)

v7: mask modified without rmw (Ville Syrjälä)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we dont have semaphores enabled, we allocate 4
dwords for signalling. But end up emitting more regardless.

Fix this by bailing out early if semaphores are not enabled.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78274
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78283Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Added as generic parameters which will be initialized in the panel
driver and are specific to panels.

Backlight delays have also kept as placeholders and will be used used
once we have MIPI backlight enabling support
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In VBT fields operation mode is 0 for Video mode and 1 for command mode.
This field will be directly used as is in generic panel driver. So
adjust accordingly.
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These are generated with intel-gpu-tools/tools/null_state_gen

v2: Don't use header file for states (Daniel Vetter)

v3: Proper URB state size for gen8/GT3 (Damien Lespiau)

Tested-by: Kristen Carlson Accardi <kristen@linux.intel.com> (v1)
Tested-by: Oscar Mateo <oscar.mateo@intel.com> (v2)
Acked-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HW guys say that it is not a cool idea to let device
go into rc6 without proper 3d pipeline state.

For each new uninitialized context, generate a
valid null render state to be run on context
creation.

This patch introduces a skeleton with empty states.

v2: - No need to vmap (Chris Wilson)
    - use .c files for state (Daniel Vetter)
    - no need to flush as i915_add_request does it
    - remove parameter for batch alloc size
    - don't wait for the init (Ben Widawsky)

v3: - move to cpu/gpu (Chris Wilson)

Tested-by: Kristen Carlson Accardi <kristen@linux.intel.com> (v1)
Tested-by: NOscar Mateo <oscar.mateo@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>