[ Upstream commit 7c4042a4d0b7532cfbc90478fd3084b2dab5849e ]

When dif and first burst is used in a write command wqe, the driver was not
properly setting fields in the io command request. This resulted in no dif
bytes being sent and invalid xfer_rdy's, resulting in the io being aborted
by the hardware.

Correct the wqe initializaton when both dif and first burst are used.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5a9eeff57f340238c39c95d8e7e54c96fc722de7 ]

Driver is hitting null pring pointers in lpfc_do_work().

Pointer assignment occurs based on SLI-revision. If recovering after an
error, its possible the sli revision for the port was cleared, making the
lpfc_phba_elsring() not return a ring pointer, thus the null pointer.

Add SLI revision checking to lpfc_phba_elsring() and status checking to all
callers.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e7f411049f5164ee6db6c3434c07302846f09990 ]

This patch does not change any functionality but avoids that sparse
complains about the queue_cmd_ring() function and its callers.

Fixes: 6fd0ce79 ("tcmu: prep queue_cmd_ring to be used by unmap wq")
Reviewed-by: NDavid Disseldorp <ddiss@suse.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 24906a41eecb73d51974ade0847c21e429beec60 ]

The owner member of struct pwm_ops must be set to THIS_MODULE to
increase the reference count of the module such that the module cannot
be removed while its code is in use.

Fixes: daa5abc4 ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8e9c523016cf9983b295e4bc659183d1fa6ef8e0 ]

There are two callers of this function and they both unlock the mutex so
this ends up being a double unlock.

Fixes: 44ed167d ("drbd: rcu_read_lock() and rcu_dereference() for tconn->net_conf")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 285531f9e6774e3be71da6673d475ff1a088d675 ]

In the first 5 minutes after boot (time of INITIAL_JIFFIES),
ieee80211_sta_last_active() returns zero if last_ack is zero. This
leads to "inactive time" showing jiffies_to_msecs(jiffies).

 # iw wlan0 station get fc:ec:da:64:a6:dd
 Station fc:ec:da:64:a6:dd (on wlan0)
	inactive time:	4294894049 ms
	.
	.
	connected time:	70 seconds

Fix by returning last_rx if last_ack == 0.
Signed-off-by: NAhmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20191031121243.27694-1-anzaki@gmail.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 71e67c3bd127cfe7863f54e4b087eba1cc8f9a7a ]

The FQ implementation used by mac80211 allocates memory using kmalloc(),
which can fail; and Johannes reported that this actually happens in
practice.

To avoid this, switch the allocation to kvmalloc() instead; this also
brings fq_impl in line with all the FQ qdiscs.

Fixes: 557fc4a0 ("fq: add fair queuing framework")
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NToke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191105155750.547379-1-toke@redhat.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ff29fde84d1fc82f233c7da0daa3574a3942bec7 ]

If someone requests fscache on the mount, and the kernel doesn't
support it, it should fail the mount.

[ Drop ceph prefix -- it's provided by pr_err. ]
Signed-off-by: NJeff Layton <jlayton@kernel.org>
Reviewed-by: NIlya Dryomov <idryomov@gmail.com>
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 17fdd7638cb687cd7f15a48545f25d738f0101e0 ]

The "read-modify-write register index" function is declared with a
confusing prototype: the "mask" and "reg" arguments are swapped.

Fortunately, this does not affect callers so far. Both arguments are
u32, and the wrapper macros (ocelot_rmw_ix etc) have the arguments in
the correct order (the one from ocelot_io.c).
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 0686bd9d5e6863f60e4bb1e78e6fe7bb217a0890 ]

The phy_init_hw() function may reset the PHY to a configuration
that does not match manual network settings stored in the phydev
structure. If the phy state machine is polled rather than event
driven this can create a timing hazard where the phy state machine
might alter the settings stored in the phydev structure from the
value read from the BMCR.

This commit follows invocations of phy_init_hw() by the bcmgenet
driver with invocations of the genphy_config_aneg() function to
ensure that the BMCR is written to match the settings held in the
phydev structure. This prevents the risk of manual settings being
accidentally altered.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 3a55402c93877d291b0a612d25edb03d1b4b93ac ]

As noted in commit 28c2d1a7 ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.

The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.

The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.

This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.

In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.

This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.

The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8731acc5068eb3f422a45c760d32198175c756f8 ]

gcc's -freorder-blocks-and-partition option makes it group frequently
and infrequently used code in .text.hot and .text.unlikely sections
respectively.  At least when building modules on s390, this option is
used by default.

gdb assumes that all code is located in .text section, and that .text
section is located at module load address.  With such modules this is no
longer the case: there is code in .text.hot and .text.unlikely, and
either of them might precede .text.

Fix by explicitly telling gdb the addresses of code sections.

It might be tempting to do this for all sections, not only the ones in
the white list.  Unfortunately, gdb appears to have an issue, when
telling it about e.g. loadable .note.gnu.build-id section causes it to
think that non-loadable .note.Linux section is loaded at address 0,
which in turn causes NULL pointers to be resolved to bogus symbols.  So
keep using the white list approach for the time being.

Link: http://lkml.kernel.org/r/20191028152734.13065-1-iii@linux.ibm.comSigned-off-by: NIlya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: NJan Kiszka <jan.kiszka@siemens.com>
Cc: Kieran Bingham <kbingham@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit eaf072e512d54c95b0977eda06cbca3151ace1e5 ]

Do not support mmap in S/PDIF mode. In S/PDIF mode
the buffer has to be copied, to allow the channel status
bits insertion.
Signed-off-by: NOlivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191104133654.28750-1-olivier.moysan@st.comSigned-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2c77734642d52448aca673e889b39f981110828b ]

The left time value is wrong when we get it by sysfs. The left time value
should be equal to preset timeout value minus elapsed time value. According
to the Meson-GXB/GXL datasheets which can be found at [0], the timeout value
is saved to BIT[0-15] of the WATCHDOG_TCNT, and elapsed time value is saved
to BIT[16-31] of the WATCHDOG_TCNT.

[0]: http://linux-meson.com

Fixes: 683fa50f ("watchdog: Add Meson GXBB Watchdog Driver")
Signed-off-by: NXingyu Chen <xingyu.chen@amlogic.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NKevin Hilman <khilman@baylibre.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 27a0e54bae09d2dd023a01254db506d61cc50ba1 ]

In mcp251x_restart_work_handler() the variable to stop the interrupt
handler (priv->force_quit) is reset after the chip is restarted and thus
a interrupt might occur.

This patch fixes the potential race condition by resetting force_quit
before enabling interrupts.
Signed-off-by: NTimo Schlüßler <schluessler@krause.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 758124335a9dd649ab820bfb5b328170919ee7dc ]

The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.

This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Reported-by: NMartin Hundebøll <martin@geanix.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1f7f504dcd9d1262437bdcf4fa071e41dec1af03 ]

In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.

If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.

In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.

Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.

Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.

With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c2a9f74c9d18acfdcabd3361adc7eac82c537a66 ]

In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.

However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.

Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
Signed-off-by: NJeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

can: rx-offload: can_rx_offload_offload_one(): use ERR_PTR() to propagate error value in case of errors

[ Upstream commit d763ab3044f0bf50bd0e6179f6b2cf1c125d1d94 ]

Before this patch can_rx_offload_offload_one() returns a pointer to a
skb containing the read CAN frame or a NULL pointer.

However the meaning of the NULL pointer is ambiguous, it can either mean
the requested mailbox is empty or there was an error.

This patch fixes this situation by returning:
- pointer to skb on success
- NULL pointer if mailbox is empty
- ERR_PTR() in case of an error

All users of can_rx_offload_offload_one() have been adopted, no
functional change intended.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4e9016bee3bf0c24963097edace034ff205b565c ]

If the rx-offload skb_queue is full or the skb allocation fails (due to OOM),
the mailbox contents is discarded.

This patch adds the incrementing of the rx_fifo_errors statistics counter.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

can: rx-offload: can_rx_offload_offload_one(): do not increase the skb_queue beyond skb_queue_len_max

[ Upstream commit a2dc3f5e1022a5ede8af9ab89a144f1e69db8636 ]

The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.

Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.

This patch limits the rx-offload skb_queue length to skb_queue_len_max.

Fixes: d254586c ("can: rx-offload: Add support for HW fifo based irq offloading")
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6caf8a6d6586d44fd72f4aa1021d14aa82affafb ]

If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.

This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.

The return value is adjusted to -ENOBUFS to better reflect the actual
problem.

The device stats handling is left to the caller.

Fixes: d254586c ("can: rx-offload: Add support for HW fifo based irq offloading")
Reported-by: NKurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 23c5a9488f076bab336177cd1d1a366bd8ddf087 ]

When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.

According to [1], the C_CAN module doesn't have the software reset.

[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdfSigned-off-by: NJeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 128a1b87d3ceb2ba449d5aadb222fe22395adeb0 ]

While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.

Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: NJeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b23c0742c2ce7e33ed79d10e451f70fdb5ca85d1 ]

xt_in() returns NULL in the output hook, skip the pkt_type change for
that case, redirection only makes sense in broute/prerouting hooks.
Reported-by: NTom Yan <tom.ty89@gmail.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: cf3cb246 ("bridge: ebtables: fix reception of frames DNAT-ed to bridge device/port")
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c43eab3eddb4c6742ac20138659a9b701822b274 ]

This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: NChuhong Yuan <hslester96@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 81a41901ffd46bac6df4c95b8290ac259e0feda8 ]

Commit 3d8598fb ("clk: ti: clkctrl: use fallback udelay approach if
timekeeping is suspended") added handling for cases when timekeeping is
suspended. But looks like we can still get occasional "failed to enable"
errors on the PM runtime resume path with udelay() returning faster than
expected.

With ti-sysc interconnect target module driver this leads into device
failure with PM runtime failing with "failed to enable" clkctrl error.

Let's fix the issue with a delay of two times the desired delay as in
often done for udelay() to account for the inaccuracy.

Fixes: 3d8598fb ("clk: ti: clkctrl: use fallback udelay approach if timekeeping is suspended")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Link: https://lkml.kernel.org/r/20190930154001.46581-1-tony@atomide.comTested-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NStephen Boyd <sboyd@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9982b0f69b49931b652d35f86f519be2ccfc7027 ]

ti_clk_register() calls it already so the driver should not create
duplicated alias.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lkml.kernel.org/r/20191002083436.10194-1-peter.ujfalusi@ti.comSigned-off-by: NStephen Boyd <sboyd@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 26467b0f8407cbd628fa5b7bcfd156e772004155 ]

When a mon group is being deleted, rdtgrp->flags is set to RDT_DELETED
in rdtgroup_rmdir_mon() firstly. The structure of rdtgrp will be freed
until rdtgrp->waitcount is dropped to 0 in rdtgroup_kn_unlock() later.

During the window of deleting a mon group, if an application calls
rdtgroup_mondata_show() to read mondata under this mon group,
'rdtgrp' returned from rdtgroup_kn_lock_live() is a NULL pointer when
rdtgrp->flags is RDT_DELETED. And then 'rdtgrp' is passed in this path:
rdtgroup_mondata_show() --> mon_event_read() --> mon_event_count().
Thus it results in NULL pointer dereference in mon_event_count().

Check 'rdtgrp' in rdtgroup_mondata_show(), and return -ENOENT
immediately when reading mondata during the window of deleting a mon
group.

Fixes: d89b7379 ("x86/intel_rdt/cqm: Add mon_data")
Signed-off-by: NXiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Reviewed-by: NFenghua Yu <fenghua.yu@intel.com>
Reviewed-by: NTony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: pei.p.jia@intel.com
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1572326702-27577-1-git-send-email-xiaochen.shen@intel.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b7e9728f3d7fc5c5c8508d99f1675212af5cfd49 ]

Attempting to allocate an entry at 0xffffffff when one is already
present would succeed in allocating one at 2^32, which would confuse
everything.  Return -ENOSPC in this case, as expected.
Signed-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f6341c5af4e6e15041be39976d16deca789555fa ]

If there is an entry at INT_MAX then idr_for_each_entry() will increment
id after handling it.  This is undefined behaviour, and is caught by
UBSAN.  Adding 1U to id forces the operation to be carried out as an
unsigned addition which (when assigned to id) will result in INT_MIN.
Since there is never an entry stored at INT_MIN, idr_get_next() will
return NULL, ending the loop as expected.
Signed-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 7de086909365cd60a5619a45af3f4152516fd75c ]

We have seen many crashes on powerpc hosts while loading bpf programs.

The problem here is that bpf_int_jit_compile() does a first pass
to compute the program length.

Then it allocates memory to store the generated program and
calls bpf_jit_build_body() a second time (and a third time
later)

What I have observed is that the second bpf_jit_build_body()
could end up using few more words than expected.

If bpf_jit_binary_alloc() put the space for the program
at the end of the allocated page, we then write on
a non mapped memory.

It appears that bpf_jit_emit_tail_call() calls
bpf_jit_emit_common_epilogue() while ctx->seen might not
be stable.

Only after the second pass we can be sure ctx->seen wont be changed.

Trying to avoid a second pass seems quite complex and probably
not worth it.

Fixes: ce076141 ("powerpc/bpf: Implement support for tail calls")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Sandipan Das <sandipan@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191101033444.143741-1-edumazet@google.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 04ec044b7d30800296824783df7d9728d16d7567 ]

To remove that test_attr__{enabled/open} are used by perf-sys.h, we
set HAVE_ATTR_TEST to zero.
Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com>
Tested-by: NKP Singh <kpsingh@google.com>
Acked-by: NSong Liu <songliubraving@fb.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Link: http://lore.kernel.org/bpf/20191001113307.27796-3-bjorn.topel@gmail.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e614f341253f8541baf0230a8dc6a016b544b1e2 ]

Without enabling keep-power-in-suspend, we can't wake the device
up using WOL packet, and the log is flooded with these messages
on resume:

sunxi-mmc 1c10000.mmc: send stop command failed
sunxi-mmc 1c10000.mmc: data error, sending stop command
sunxi-mmc 1c10000.mmc: send stop command failed
sunxi-mmc 1c10000.mmc: data error, sending stop command

So to make the WiFi really a wakeup-source, we need to keep it powered
during suspend.

Fixes: 0e233720 ("arm: dts: sun8i: Add the TBS A711 tablet devicetree")
Signed-off-by: NOndrej Jirman <megous@megous.com>
Signed-off-by: NMaxime Ripard <mripard@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit cdfc2e2086bf9c465f44e2db25561373b084a113 ]

The zero'ing of bits 16 and 18 is incorrect. Currently the code
is masking with the bitwise-and of BIT(16) & BIT(18) which is
0, so the updated value for val is always zero. Fix this by bitwise
and-ing value with the correct mask that will zero bits 16 and 18.

Addresses-Coverity: (" Suspicious &= or |= constant expression")
Fixes: b8eb71dc ("clk: sunxi-ng: Add A80 CCU")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMaxime Ripard <mripard@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit afdc74ed2d57e86c10b1d6831339770a802bab9a ]

r375326 in Clang exposes an issue with operator precedence in
sunxi_div_clk_setup:

drivers/clk/sunxi/clk-sunxi.c:1083:30: warning: operator '?:' has lower
precedence than '|'; '|' will be evaluated first
[-Wbitwise-conditional-parentheses]
                                                 data->div[i].critical ?
                                                 ~~~~~~~~~~~~~~~~~~~~~ ^
drivers/clk/sunxi/clk-sunxi.c:1083:30: note: place parentheses around
the '|' expression to silence this warning
                                                 data->div[i].critical ?
                                                                       ^
                                                                      )
drivers/clk/sunxi/clk-sunxi.c:1083:30: note: place parentheses around
the '?:' expression to evaluate it first
                                                 data->div[i].critical ?
                                                                       ^
                                                 (
1 warning generated.

It appears that the intention was for ?: to be evaluated first so that
CLK_IS_CRITICAL could be added to clkflags if the critical boolean was
set; right now, | is being evaluated first. Add parentheses around the
?: block to have it be evaluated first.

Fixes: 9919d44f ("clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks")
Link: https://github.com/ClangBuiltLinux/linux/issues/745Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NMaxime Ripard <mripard@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 658fd65cf0b0d511de1718e48d9a28844c385ae0 ]

It is not allowed to sleep to early in the boot process and this may lead
to kernel issues if the bootloader didn't prepare the slow clock and main
clock.

This results in the following error and dump stack on the AriettaG25:
   bad: scheduling from the idle thread!

Ensure it is possible to sleep, else simply have a delay.
Reported-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lkml.kernel.org/r/20190920153906.20887-1-alexandre.belloni@bootlin.com
Fixes: 80eded6c ("clk: at91: add slow clks driver")
Tested-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NStephen Boyd <sboyd@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f430c7ed8bc22992ed528b518da465b060b9223f ]

Add a missing short description to the reset_control_ops documentation.
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
[p.zabel@pengutronix.de: rebased and updated commit message]
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 7e5d0bf6afcc7bd72f78e7f33570e2e0945624f0 ]

Since commit a211b8c5 ("ARM: dts: imx6qdl-sabreauto: Add sensors")
a storm of accelerometer interrupts is seen:

[  114.211283] irq 260: nobody cared (try booting with the "irqpoll" option)
[  114.218108] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.4 #1
[  114.223960] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[  114.230531] [<c0112858>] (unwind_backtrace) from [<c010cdc8>] (show_stack+0x10/0x14)
[  114.238301] [<c010cdc8>] (show_stack) from [<c0c1aa1c>] (dump_stack+0xd8/0x110)
[  114.245644] [<c0c1aa1c>] (dump_stack) from [<c0193594>] (__report_bad_irq+0x30/0xc0)
[  114.253417] [<c0193594>] (__report_bad_irq) from [<c01933ac>] (note_interrupt+0x108/0x298)
[  114.261707] [<c01933ac>] (note_interrupt) from [<c018ffe4>] (handle_irq_event_percpu+0x70/0x80)
[  114.270433] [<c018ffe4>] (handle_irq_event_percpu) from [<c019002c>] (handle_irq_event+0x38/0x5c)
[  114.279326] [<c019002c>] (handle_irq_event) from [<c019438c>] (handle_level_irq+0xc8/0x154)
[  114.287701] [<c019438c>] (handle_level_irq) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[  114.296166] [<c018eda0>] (generic_handle_irq) from [<c0534214>] (mxc_gpio_irq_handler+0x30/0xf0)
[  114.304975] [<c0534214>] (mxc_gpio_irq_handler) from [<c0534334>] (mx3_gpio_irq_handler+0x60/0xb0)
[  114.313955] [<c0534334>] (mx3_gpio_irq_handler) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[  114.322762] [<c018eda0>] (generic_handle_irq) from [<c018f3ac>] (__handle_domain_irq+0x64/0xe0)
[  114.331485] [<c018f3ac>] (__handle_domain_irq) from [<c05215a8>] (gic_handle_irq+0x4c/0xa8)
[  114.339862] [<c05215a8>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
[  114.347361] Exception stack(0xc1301ec0 to 0xc1301f08)
[  114.352435] 1ec0: 00000001 00000006 00000000 c130c340 00000001 c130f688 9785636d c13ea2e8
[  114.360635] 1ee0: 9784907d 0000001a eaf99d78 0000001a 00000000 c1301f10 c0182b00 c0878de4
[  114.368830] 1f00: 20000013 ffffffff
[  114.372349] [<c0101a70>] (__irq_svc) from [<c0878de4>] (cpuidle_enter_state+0x168/0x5f4)
[  114.380464] [<c0878de4>] (cpuidle_enter_state) from [<c08792ac>] (cpuidle_enter+0x28/0x38)
[  114.388751] [<c08792ac>] (cpuidle_enter) from [<c015ef9c>] (do_idle+0x224/0x2a8)
[  114.396168] [<c015ef9c>] (do_idle) from [<c015f3b8>] (cpu_startup_entry+0x18/0x20)
[  114.403765] [<c015f3b8>] (cpu_startup_entry) from [<c1200e54>] (start_kernel+0x43c/0x500)
[  114.411958] handlers:
[  114.414302] [<a01028b8>] irq_default_primary_handler threaded [<fd7a3b08>] mma8452_interrupt
[  114.422974] Disabling IRQ #260

           CPU0       CPU1
....
260:     100001          0  gpio-mxc  31 Level     mma8451

The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin
needs to activate its pull up, otherwise it will stay always at low level
generating multiple interrupts.

The current device tree does not configure the IOMUX for this pin, so
it uses whathever comes configured from the bootloader.

The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from
the bootloader, which has PKE bit cleared, hence disabling the
pull-up.

Instead of relying on a previous configuration from the bootloader,
configure the GPIO6_IO31 pin with pull-up enabled in order to fix
this problem.

Fixes: a211b8c5 ("ARM: dts: imx6qdl-sabreauto: Add sensors")
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-By: NLeonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 67d33aecd030226f0a577eb683aaa6853ecf8f91 ]

Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:

"detected irqchip that is shared with multiple gpiochips: please fix the driver."

Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.

This patch is heavily based on the attachment to the bug by Christoph Marz.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543
Fixes: 6e08d6bb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on: 83b9dc11 ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain")
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>