When the system has no lmb bram, main memory should be start from
zero because of microblaze vectors.

DTS fragment could look like:
	DDR2_SDRAM: memory@0 {
		device_type = "memory";
		reg = < 0x0 0x10000000 >;
	} ;

Then you have to setup CONFIG_KERNEL_BASE_ADDR=0 which caused
that kernel physical start address will be zero. On reset vector place
will be jump to 0x100 and on 0x100 starts kernel text.

You have to solve how to load the kernel before cpu starts.
Tested with XMD.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Last sync.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Move to generic location.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

noMMU and MMU use them.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Here is small regression on dhrystone tests and I think
that on all benchmarking tests. It is due to better checking
mechanism in put_user macro
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Use unified version.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Previous patches fixed only MMU version and this is the first
patch for noMMU kernel
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Generic implementation for noMMU and MMU version
Signed-off-by: NMichal Simek <monstr@monstr.eu>

copy_from_user macro also use copy_tofrom_user function
Signed-off-by: NMichal Simek <monstr@monstr.eu>

noMMU and MMU kernel will use copy copy_tofrom_user
asm implementation.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Add macro description and resort.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Use FIXUP macros and resort them.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

It is used __FIXUP_SECTION and __EX_TABLE_SECTION macros.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

This is the first patch which does uaccess unification.
I choosed to do several patches to be able to use bisect
in future if any fault happens.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

The same noMMU and MMU functions should be placed in
one file.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Just sort to be able remove whole block.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

I would like to use asm-generic uaccess.h where are segment
macros defined. This is just first step.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

We don't need to do it.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

If CONFIG_INITRAMFS_SOURCE is set, "scripts/gen_initramfs_list.sh"
checks if the cpio image exists. Remove the duplicate check from the
Makefile.

Remove the "clean-kernel" variable which is unused in the Makefile and
is not used by the Kbuild.
Signed-off-by: NArun Bhanu <arun@bhanu.net>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

'make clean' does not to delete the following build generated file:
	arch/microblaze/boot/linux.bin.ub

'make mrproper' does not to delete the following build generated files:
	arch/microblaze/boot/simpleImage.*

Fix the Makefile to delete these build generated files.

See [1] for a discussion on why simpleImage.* files are deleted with 'make
mrproper' and not with 'make clean'.
	[1] http://lkml.org/lkml/2010/3/12/96Signed-off-by: NArun Bhanu <arun@bhanu.net>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

'make ARCH=microblaze help' fails with the following error due to a
missing single quote.

/bin/sh: -c: line 0: unexpected EOF while looking for matching `''
/bin/sh: -c: line 1: syntax error: unexpected end of file
make: *** [help] Error 2
Signed-off-by: NArun Bhanu <arun@bhanu.net>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

The "kstack=" command line parameter is not parsed correctly.
All proper values are interpreted as zero.
Signed-off-by: NSteven J. Magnani <steve@digidescorp.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Add a MAINTAINERS record for the key management facility.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  CRED: Fix memory leak in error handling

* git://git.kernel.org/pub/scm/linux/kernel/git/joern/logfs:
  [LogFS] Erase new journal segments
  [LogFS] Move reserved segments with journal
  [LogFS] Clear PagePrivate when moving journal
  Simplify and fix pad_wbuf
  Prevent data corruption in logfs_rewrite_block()
  Use deactivate_locked_super
  Fix logfs_get_sb_final error path
  Write out both superblocks on mismatch
  Prevent schedule while atomic in __logfs_readdir
  Plug memory leak in writeseg_end_io
  Limit max_pages for insane devices
  Open segment file before using it

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Do not free zero sized per cpu areas
  x86: Make sure free_init_pages() frees pages on page boundary
  x86: Make smp_locks end with page alignment

Fix a memory leak on an OOM condition in prepare_usermodehelper_creds().
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  ocfs2: Fix a race in o2dlm lockres mastery
  Ocfs2: Handle deletion of reflinked oprhan inodes correctly.
  Ocfs2: Journaling i_flags and i_orphaned_slot when adding inode to orphan dir.
  ocfs2: Clear undo bits when local alloc is freed
  ocfs2: Init meta_ac properly in ocfs2_create_empty_xattr_block.
  ocfs2: Fix the update of name_offset when removing xattrs
  ocfs2: Always try for maximum bits with new local alloc windows
  ocfs2: set i_mode on disk during acl operations
  ocfs2: Update i_blocks in reflink operations.
  ocfs2: Change bg_chain check for ocfs2_validate_gd_parent.
  [PATCH] Skip check for mandatory locks when unlocking

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (28 commits)
  ceph: update discussion list address in MAINTAINERS
  ceph: some documentations fixes
  ceph: fix use after free on mds __unregister_request
  ceph: avoid loaded term 'OSD' in documention
  ceph: fix possible double-free of mds request reference
  ceph: fix session check on mds reply
  ceph: handle kmalloc() failure
  ceph: propagate mds session allocation failures to caller
  ceph: make write_begin wait propagate ERESTARTSYS
  ceph: fix snap rebuild condition
  ceph: avoid reopening osd connections when address hasn't changed
  ceph: rename r_sent_stamp r_stamp
  ceph: fix connection fault con_work reentrancy problem
  ceph: prevent dup stale messages to console for restarting mds
  ceph: fix pg pool decoding from incremental osdmap update
  ceph: fix mds sync() race with completing requests
  ceph: only release unused caps with mds requests
  ceph: clean up handle_cap_grant, handle_caps wrt session mutex
  ceph: fix session locking in handle_caps, ceph_check_caps
  ceph: drop unnecessary WARN_ON in caps migration
  ...

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (asc7621) Add X58 entry in Kconfig
  hwmon: (w83793) Saving negative errors in unsigned
  hwmon: (coretemp) Add missing newline to dev_warn() message
  hwmon: (coretemp) Fix cpu model output

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  pata_via: fix VT6410/6415/6330 detection issue

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
  r8169: offical fix for CVE-2009-4537 (overlength frame DMAs)
  ipv6: Don't drop cache route entry unless timer actually expired.
  tulip: Add missing parens.
  r8169: fix broken register writes
  pcnet_cs: add new id
  bonding: fix broken multicast with round-robin mode
  drivers/net: Fix continuation lines
  e1000: do not modify tx_queue_len on link speed change
  net: ipmr/ip6mr: prevent out-of-bounds vif_table access
  ixgbe: Do not run all Diagnostic offline tests when VFs are active
  igb: use correct bits to identify if managability is enabled
  benet: Fix compile warnnings in drivers/net/benet/be_ethtool.c
  net: Add MSG_WAITFORONE flag to recvmmsg
  e1000e: do not modify tx_queue_len on link speed change
  igbvf: do not modify tx_queue_len on link speed change
  ipv4: Restart rt_intern_hash after emergency rebuild (v2)
  ipv4: Cleanup struct net dereference in rt_intern_hash
  net: fix netlink address dumping in IPv4/IPv6
  tulip: Fix null dereference in uli526x_rx_packet()
  gianfar: fix undo of reserve()
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Properly truncate pt_regs framepointer in perf callback.
  arch/sparc/kernel: Use set_cpus_allowed_ptr
  sparc: Fix use of uid16_t and gid16_t in asm/stat.h

In commit 9df93939 ("ext3: Use bitops to read/modify
EXT3_I(inode)->i_state") ext3 changed its internal 'i_state' variable to
use bitops for its state handling.  However, unline the same ext4
change, it didn't actually change the name of the field when it changed
the semantics of it.

As a result, an old use of 'i_state' remained in fs/ext3/ialloc.c that
initialized the field to EXT3_STATE_NEW.  And that does not work
_at_all_ when we're now working with individually named bits rather than
values that get masked.  So the code tried to mark the state to be new,
but in actual fact set the field to EXT3_STATE_JDATA.  Which makes no
sense at all, and screws up all the code that checks whether the inode
was newly allocated.

In particular, it made the xattr code unhappy, and caused various random
behavior, like apparently

	https://bugzilla.redhat.com/show_bug.cgi?id=577911

So fix the initialization, and rename the field to match ext4 so that we
don't have this happen again.

Cc: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Daniel J Walsh <dwalsh@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Official patch to fix the r8169 frame length check error.

Based on this initial thread:
http://marc.info/?l=linux-netdev&m=126202972828626&w=1
This is the official patch to fix the frame length problems in the r8169
driver.  As noted in the previous thread, while this patch incurs a performance
hit on the driver, its possible to improve performance dynamically by updating
the mtu and rx_copybreak values at runtime to return performance to what it was
for those NICS which are unaffected by the ideosyncracy (if there are any).

Summary:

    A while back Eric submitted a patch for r8169 in which the proper
allocated frame size was written to RXMaxSize to prevent the NIC from dmaing too
much data.  This was done in commit fdd7b4c3.  A
long time prior to that however, Francois posted
126fa4b9, which expiclitly disabled the MaxSize
setting due to the fact that the hardware behaved in odd ways when overlong
frames were received on NIC's supported by this driver.  This was mentioned in a
security conference recently:
http://events.ccc.de/congress/2009/Fahrplan//events/3596.en.html

It seems that if we can't enable frame size filtering, then, as Eric correctly
noticed, we can find ourselves DMA-ing too much data to a buffer, causing
corruption.  As a result is seems that we are forced to allocate a frame which
is ready to handle a maximally sized receive.

This obviously has performance issues with it, so to mitigate that issue, this
patch does two things:

1) Raises the copybreak value to the frame allocation size, which should force
appropriately sized packets to get allocated on rx, rather than a full new 16k
buffer.

2) This patch only disables frame filtering initially (i.e., during the NIC
open), changing the MTU results in ring buffer allocation of a size in relation
to the new mtu (along with a warning indicating that this is dangerous).

Because of item (2), individuals who can't cope with the performance hit (or can
otherwise filter frames to prevent the bug), or who have hardware they are sure
is unaffected by this issue, can manually lower the copybreak and reset the mtu
such that performance is restored easily.
Signed-off-by: NNeil Horman <nhorman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For 32-bit processes, we save the full 64-bits of the regs in pt_regs.

But unlike when the userspace actually does load and store
instructions, the top 32-bits don't get automatically truncated by the
cpu in kernel mode (because the kernel doesn't execute with PSTATE_AM
address masking enabled).

So we have to do it by hand.
Reported-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Intel X58 have asc7621a chip. So added X58 entry in Kconfig for asc7621.
Also arranged existing models in ascending order.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

"ret" is used to store the return value for watchdog_trigger() and it
should be signed for the error handling to work.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add missing newline to dev_warn() message string. This is more of an issue
with older kernels that don't automatically add a newline if it was missing
from the end of the previous line.
Signed-off-by: NDean Nelson <dnelson@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NJean Delvare <khali@linux-fr.org>