This patch (as818b) simplifies autosuspend processing by keeping track
of the number of unsuspended children of each USB hub.  This will
permit us to avoid a good deal of unnecessary work all the time; we
will no longer have to create a bunch of workqueue entries to carry
out autosuspend requests, only to have them fail because one of the
hub's children isn't suspended.

The basic idea is simple.  There already is a usage counter in the
usb_device structure for preventing autosuspends.  The patch just
increments that counter for every unsuspended child.  There's only one
tricky part: When a device disconnects we need to remember whether it
was suspended at the time (leave the counter alone) or not (decrement
the counter).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as817) simplifies the remote-wakeup processing in the hub
driver.  Now instead of using a specialized code path, it relies on
the standard USB resume routines.  The hub_port_resume() function does
an initial get_port_status() to see whether the port has already
resumed itself (as it does when a remote-wakeup request is sent).
This will slow down handling of other resume events slightly, but not
enough to matter.

The patch also changes the hub_port_status() routine, making it return
an error if a short reply is received.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as816) changes an existing flag in the usb_device
structure to a bitflag, preparing the way for more bitflags to come
in the future.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Unlike UHCI, OHCI does not exert any DMA load on the system when no
devices are connected.  Consequently there is no advantage to doing
an autostop other than the power savings, so we shouldn't compile the
necessary code unless CONFIG_PM is enabled.

This patch (as820) makes the root-hub suspend and resume routines
conditional on CONFIG_PM.  It also prevents autostop from activating
if the device_may_wakeup flag isn't set; some people use this flag to
alert the driver about Resume-Detect bugs in the hardware.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as742b) adds autosuspend/autoresume support to the USB hub
driver.  The largest aspect of the change is that we no longer need a
special flag for root hubs that want to be resumed.  Now every hub is
autoresumed whenever khubd needs to access it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as738b) fixes numerous problems in the controller/root-hub
suspend/resume/remote-wakeup support in ehci-hcd:

	The bus_resume() routine should wake up only the ports that
	were suspended by bus_suspend().  Ports that were already
	suspended should remain that way.

	The interrupt mask is used to detect loss of power in the
	bus_resume() routine (if the mask is 0 then power was lost).
	However bus_suspend() always sets the mask to 0.  Instead the
	mask should retain its normal value, with port-change-detect
	interrupts disabled if remote wakeup is turned off.

	The interrupt mask should be reset to its correct value at the
	end of bus_resume() regardless of whether power was lost.

	bus_resume() reinitializes the operational registers if power
	was lost.  However those registers are not in the aux power
	well, hence they can lose their values whenever the controller
	is put into D3.  They should always be reinitialized.

	When a port-change interrupt occurs and the root hub is
	suspended, the interrupt handler should request a root-hub
	resume instead of starting up the controller all by itself.

	There's no need for the interrupt handler to request a
	root-hub resume every time a suspended port sends a
	remote-wakeup request.

	The pci_resume() method doesn't need to check for connected
	ports when deciding whether or not to reset the controller.
	It can make that decision based on whether Vaux power was
	maintained.

	Even when the controller does not need to be reset,
	pci_resume() must undo the effect of pci_suspend() by
	re-enabling the interrupt mask.

	If power was lost, pci_resume() must not call ehci_run().
	At this point the root hub is still supposed to be suspended,
	not running.  It's enough to rewrite the command register and
	set the configured_flag.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Might speed up some systems.  If nothing else, a bad driver should not
take the whole USB subsystem down with it.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It's a simple usb-serial driver that just creates a tty device to read
and write from.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is an update for Greg K-H's proposed usbfs2:
http://sourceforge.net/mailarchive/message.php?msg_id=19295229

It creates a dynamic major for USB endpoints and fixes
the endpoint minor calculation.
Signed-off-by: NSarah Bailey <saharabeara@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

there is an error path in the pegasus driver which can leave
the task in TASK_UNINTERRUPTIBLE. Depending on when it
schedules next, this can be bad.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the latest update for asix.c reverted some endianness fixes. This
reinstates them.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We do already have both the code and a config option, so why not build
this driver?  ;-)
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace kmalloc+memset with kzalloc
Signed-off-by: NYan Burman <yan_952@hotmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use canonical defines for the Apple USB device IDs.
Also add the Geyser IV devices missing in my previous patch.
Signed-off-by: NJulien BLACHE <jb@jblache.org>
Acked-by: NDmitry Torokhov <dtor@insightbb.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Just digging through code and found these needless variable initializations. So here is the patch.
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb_device_match() can now become static.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove minor double-declaration goof.
Signed-off-by: NMilan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make the pxa2xx_udc driver recognize a newer revision of the IXP425 chip.
Signed-off-by: NMilan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds support for the DMC TSC-10 and TSC-25 usb touchscreen controllers.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch contains the following possible cleanups:
- make the needlessly global ftdi_release_platform_dev() static
- remove the unused usb_ftdi_elan_read_reg()
- proper prototypes for the following functions:
  - usb_ftdi_elan_read_pcimem()
  - usb_ftdi_elan_write_pcimem()

Note that the misplaced prototypes for the latter ones in
drivers/usb/host/u132-hcd.c were buggy. Depending on the calling
convention of the architecture calling one of them could have turned
your stack into garbage.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes the needlessly global "u132_hcd_wait" static.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If at some point cypress_init() fails deregister
only the resources that were registered until that point.
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Certain boards seem to like to issue false overcurrent notifications, for
example on ports that don't have anything connected to them.  This looks
like a hardware error, at the level of noise to those ports' overcurrent
input signals (or non-debounced VBUS comparators).  This surfaces to users
as truly massive amounts of syslog spam from khubd (which is appropriate
for real hardware problems, except for the volume from multiple ports).

Using this new "ignore_oc" flag helps such systems work more sanely, by
preventing such indications from getting to khubd (and spam syslog).  The
downside is of course that true overcurrent errors will be masked; they'll
appear as spontaneous disconnects, without the diagnostics that will let
users troubleshoot issues like short circuited cables.

Note that the bulk of these reports seem to be with VIA southbridges, but
I think some were with Intel ones.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

EHCI hooks for high speed electrical tests of the root hub ports.

The expectation is that a usermode program actually triggers the test,
making the same control request it would make for an external hub.
Tests for peripheral upstream ports would issue a different request.
In all cases, the hardware needs re-initialization before it could
be used "normally" again (e.g. unplug/replug, rmmod/modprobe).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The net2280 driver is too eager to send zero-length packets when
IN tokens are received on ep0.  No such packet should be sent (the
driver should NAK) before the gadget driver has queued the proper
response.  Otherwise deferred responses are impossible.

This patch (as823) makes net2280 avoid sending ZLPs for IN transfers
on ep0 until a response has been submitted, and avoids stalling when an
OUT packet is received before a request has been submitted for an OUT
transfer on ep0.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Possible memleak fix on error path. The changes:

- out_kfree2 and out_free_urb replaced
- missing scsi_host_put() added

Here it goes:
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The mass storage device from Digitech designed for Flash Cards, as found
on (for example) the GNX4 device has issues with residue, similar to the
bug report at http://kerneltrap.org/node/6297.  This patch adds the
faulty storage device to unusual_devs.h, this not only reduces the noise
in dmesg but also increases the transfer speeds by a factor of 7x for me
(89kB/s -> 637kB/s).

T:  Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1210 ProdID=0003 Rev= 1.00
S:  Manufacturer=DigiTech HMG
S:  Product=DigiTech Mass Storage
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
Signed-off-by: NJaco Kroon <jaco@kroon.co.za>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as821) fixes a compiler warning when CONFIG_PM isn't on
("usb_autosuspend_work" defined but not used).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

> 2006/11/11, Adrian Bunk <bunk@stusta.de>:
> > The Coverity checker spotted the following in
> > drivers/usb/serial/aircable.c:
> >
> > <--  snip  -->
> >
> > ...
> > static void aircable_read(void *params)
> > {
> > ...


Hi everyone,
Sorry for the long time response but here is the patch, I think this way should
work, if anyone has any suggestion let me know. What I do now is, in case I
don't have the tty available I reschedule the work, I have tried it and it
works with no problem, I even tried removing the device, and didn't find
anything strange.
Signed-off-by: NNaranjo Manuel <naranjo.manuel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All the other root-hub suspend or resume log messages, in ohci-hcd or
any of the other host controller drivers, use the debug priority
level.  This patch (as815) makes the one single exception behave like
all the rest.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>