The power update function looks at all current vifs to determine the power
policy. It doesn't use the current vif. Instead the value was overwritten
and used internally.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In some cases, we need to force the association to be off in the
MAC_CONTEXT_CMD command we send to the firmware.  Instead of having to
hack the vif->bss_conf.assoc value, pass it all the way down the call
chain.

Additionally, for the iwl_mvm_mac_ctxt_add() case, we *always* set
forced_assoc_off to true, so we can remove the hack in the d3 code
that was forcing it to off by hacking the bss_conf.assoc value.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enabling beacon filtering should be done only after a beacon
has been received. Doing that too early will cause
disconnections.
This has already been fixed, but the fix didn't take care
about the case where the beacon is received after the
association, it waited only for association which is not
enough.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This feature has been causing trouble - disable it for now.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_mvm_power_update_mac() (more specifically
iwl_mvm_power_iterator()) relies on the phy_ctxt setting to decide
whether the vif is active or not.  When unassigning a chanctx, we
should therefore call iwl_mvm_power_update_mac() after setting
phy_chanctx to NULL.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware needs to know on what channel we run before we
set the association bit in the MAC context. Change a bit the
flow to achieve this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some APs (e.g. TP-LINK TL-WA801N) are disabling aggregation (downlink
to station) when U-APSD is enabled, resulting in low throughput.
Add a module parameter to allow disabling U-APSD support in the driver.

Also re-enable U-APSD for -9 firmware since the firmare issues were
fixed in this release.

There are devices that won't support U-APSD even with newer
firmware, so bring the TLV flag back to detect those.
Signed-off-by: NMatt Chen <matt.chen@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Prevent sched scan while not idle (including during association or in AP
mode) instead of while associated only.

This fixes my previous commit which was incomplete:

commit bd5e4744
Author: David Spinadel <david.spinadel@intel.com>
Date:   Thu Apr 24 13:15:29 2014 +0300

    iwlwifi: mvm: do no sched scan while associated

    Currently the FW doesn't support sched scan while associated,
    Prevent it.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

CMD_SYNC is really 0 which is confusing:

if (cmd.flags & CMD_SYNC) is always false.
Fix this by simply removing its definition.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There was a deadlock in monitor mode when we were setting the
channel if the channel was not 1.

======================================================
[ INFO: possible circular locking dependency detected ]
3.14.3 #4 Not tainted
-------------------------------------------------------
iw/3323 is trying to acquire lock:
 (&local->chanctx_mtx){+.+.+.}, at: [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211]

but task is already holding lock:
 (&local->iflist_mtx){+.+...}, at: [<ffffffffa0609e0a>] ieee80211_set_monitor_channel+0x5a/0x1b0 [mac80211]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (&local->iflist_mtx){+.+...}:
       [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0
       [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0
       [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0
       [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
       [<ffffffffa0518189>] iwl_mvm_recalc_multicast+0x49/0xa0 [iwlmvm]
       [<ffffffffa051822e>] iwl_mvm_configure_filter+0x4e/0x70 [iwlmvm]
       [<ffffffffa05e6d43>] ieee80211_configure_filter+0x153/0x5f0 [mac80211]
       [<ffffffffa05e71f5>] ieee80211_reconfig_filter+0x15/0x20 [mac80211]
       [snip]

-> #1 (&mvm->mutex){+.+.+.}:
       [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0
       [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0
       [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0
       [<ffffffffa0517246>] iwl_mvm_add_chanctx+0x56/0xe0 [iwlmvm]
       [<ffffffffa062ca1e>] ieee80211_new_chanctx+0x13e/0x410 [mac80211]
       [<ffffffffa062d953>] ieee80211_vif_use_channel+0x1c3/0x5a0 [mac80211]
       [<ffffffffa06035ab>] ieee80211_add_virtual_monitor+0x1ab/0x6b0 [mac80211]
       [<ffffffffa06052ea>] ieee80211_do_open+0xe6a/0x15a0 [mac80211]
       [<ffffffffa0605a79>] ieee80211_open+0x59/0x60 [mac80211]
       [snip]

-> #0 (&local->chanctx_mtx){+.+.+.}:
       [<ffffffff810d6cb7>] check_prevs_add+0x977/0x980
       [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0
       [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0
       [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0
       [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211]
       [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211]
       [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211]
       [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211]
       [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211]
       [snip]

other info that might help us debug this:

Chain exists of:
  &local->chanctx_mtx --> &mvm->mutex --> &local->iflist_mtx

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&local->iflist_mtx);
                               lock(&mvm->mutex);
                               lock(&local->iflist_mtx);
  lock(&local->chanctx_mtx);

 *** DEADLOCK ***

This deadlock actually occurs:
INFO: task iw:3323 blocked for more than 120 seconds.
      Not tainted 3.14.3 #4
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
iw              D ffff8800c8afcd80  4192  3323   3322 0x00000000
 ffff880078fdb7e0 0000000000000046 ffff8800c8afcd80 ffff880078fdbfd8
 00000000001d5540 00000000001d5540 ffff8801141b0000 ffff8800c8afcd80
 ffff880078ff9e38 ffff880078ff9e38 ffff880078ff9e40 0000000000000246
Call Trace:
 [<ffffffff817ea841>] schedule_preempt_disabled+0x31/0x80
 [<ffffffff817ebaed>] mutex_lock_nested+0x19d/0x4f0
 [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
 [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
 [<ffffffffa052a680>] ? iwl_mvm_power_mac_update_mode+0xc0/0xc0 [iwlmvm]
 [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
 [<ffffffffa0529357>] _iwl_mvm_power_update_binding+0x27/0x80 [iwlmvm]
 [<ffffffffa0516eb1>] iwl_mvm_unassign_vif_chanctx+0x81/0xc0 [iwlmvm]
 [<ffffffffa062d3ff>] __ieee80211_vif_release_channel+0xdf/0x470 [mac80211]
 [<ffffffffa062e2fa>] ieee80211_vif_release_channel+0x4a/0xb0 [mac80211]
 [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211]
 [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211]
 [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211]
 [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211]

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75541

Cc: <stable@vger.kernel.org> [3.13+]
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Stop sched scan on bss_info_changed if !idle to avoid sched scan
during association.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add an option to notify mac80211 about sched scan complete from
iwl_mvm_stop_sched_scan(), to enable this notification when the
stop was called from within the driver.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All messages should have a trailing newline, add all the
missing ones. Also make all messages constants, replacing
the single one that pointlessly used a variable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows mac80211 to flush the Tx queues before it sends
critical management frames.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Publish WIPHY_FLAG_HAS_CHANNEL_SWITCH if the fw supports
newly introduced IWL_UCODE_TLV_API_CSA_FLOW.
When CSA starts, save the switching vif inside mvm and during the CSA period
configure fw with a new beacon after each beacon transmission in order to
update the csa counters.
Also, handle correctly the CSA unbind-bind flow which is triggered by mac80211
when the actual channel switch happens.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some ampdu actions change queues by direct target access.

Since the bus is disabled in d0i3, make sure to exit d0i3
before handling these actions.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the FW doesn't support sched scan while associated,
Prevent it.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

bail out from the suspend/resume callbacks if
d0i3 is used.

declare support for ANY wowlan trigger (i.e.
normal operation).

On resume, we shouldn't execute the d0i3 exit
flow (which might disconnect stations, etc.)
until mac80211 was resumed.
Add new flags to indicate we are in suspend,
and call the pending exit work on resume.

Since the resume flow can take some time, add
a new EXIT_WORK reference type to prevent going
back to d0i3 at this stage.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This patch enables Energy Based Scan (EBS) - intended to detect energy
on 5 GHz band channels. Passive scan on this band takes up to 2.64 sec
assuming 110mSec per-channel * 24 channels. EBS is designed to detect
energy on channels with intensive Wifi activity as well as those where
only beacons are transmitted. EBS completes sampling all channels within
shortest beacon frame transmission time. Total EBS duration is about 100
msec (typical beacon interval).
Detecting Wifi activity on 5 GHz band channels can significantly reduce
scan duration thus saving time and power. EBS failure reported by FW
disables EBS for current connection. It is re-enabled upon new
connection attempt on any WLAN interface.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This firmware is not supported any more.
A few code paths specific to old firmware can be removed.
We can now assume that a few TLV flags are always set since
we won't load firmware that didn't support the corresponding
features. This will be done in a separate patch.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware doesn't support broadcast filtering on P2P
client. Trying to enable it makes the firmware assert.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If we have no beacon data before association, delay smart FIFO
enablement until after we have this data.

Not doing so can cause association failures in extremely silent
environments (usually only a shielded box/room) as beacon RX is
not sent to the host immediately, and then the association time
event ends without the host receiving any beacon even though it
was on the air - it's just stuck on the FIFO.

Cc: <stable@vger.kernel.org> [3.14]
Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The current firmware advertises support for uAPSD, but
critical bugs force us to disable the feature.
When a fixed firmware will be available, we will be able to
re-enable uAPSD.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some scan parameters should be dependent on traffic conditions.
Centralize conditions verification in one function and obtain
scan max out-of-channel and suspend time in that new function.
Rely on bound interfaces indication instead of association state
to calculate scan parameters. If no bound interfaces use default
values for out-of-channel and suspend time parameters.

Additionally, get rid of NL80211_SCAN_FLAG_LOW_PRIORITY checks
since no use case for this exists so far.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
[reword commit log a bit]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the firmware asserts, the driver will dump the firmware
state to an internal buffer. This buffer is kept aside until
it is dumped through debugfs. Once an external application
fetched the data, the buffer is freed and a new buffer can
be allocated in case another assert occurs.

A udev event is sent to trigger an external application.

A simple rule like:
DRIVER=="iwlwifi", ACTION=="change", RUN+="/sbin/dump_sram.sh"

can fetch the data from debugfs.

Here is my dump_sram.sh:

phyname=$(basename ${DEVPATH})
date=$(date +%F_%H_%M)
filename=/var/log/iwl-sram-${phyname}-${date}.bin
cat /sys/kernel/debug/ieee80211/${phyname}/iwlwifi/iwlmvm/fw_error_dump > ${filename}

The current SRAM size is 80KB so, currently:
$ ls -lh iwl-sram-phy0-2014-03-16_13_14.bin
-rw-r--r-- 1 emmanuel emmanuel 81K Mar 16 13:15 iwl-sram-phy0-2014-03-16_13_14.bin

and after compression:
$ ls -lh iwl-sram-phy0-2014-03-16_13_14.bin.xz
-rw-r--r-- 1 emmanuel emmanuel 13K Mar 16 13:15 iwl-sram-phy0-2014-03-16_13_14.bin.xz
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to restore the qos seq number on d0i3 exit,
we need to read it from the wowlan status.

However, in order to make sure we use correct seq num
for tx frames, we need to defer any outgoing frames,
and re-enqueue them only after the seq num is configured
correctly.

Sync new Tx aggregations with D0i3 so that the correct
seq num is used for them. Wait synchronously for D0i3
exit before starting a new Tx agg.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enable beacon filter only if at least one beacon from candidate
AP is received before or after association. Check this condition before
enabling BF upon secured association completion. Add BF enablement to
mac80211 event that indicates beacon is received after association.
Too early beacon filtering enablement can lead to disconnection due to
missing AP's beacon after association.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Scheduled scan was disabled because it was broken. Now it is
fixed and got disabled by mistake by a merge.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A scheduled scan is a more persistent setting and should take priority
over temporary regular scans. Abort the regular when a sched_scan
request arrives and then request the sched_scan.

The kernel API allows sending a sched_scan without canceling a regular
scan in progress, so this is our way to abstract the FW's limitations.

Make the scan-cancel Rx handler async and flush after invocation to
ensure new scans can't creep in before it.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

cfg80211 assumes a scheduled scan is stopped synchronously. Wait for the
FW before returning to caller.

Don't do anything in the async handler in the stop-from-above flow.
There's no need to call the mac80211 sched-scan completion as the
cleanup will be automatic. Make sure the async handler is called before
the next incoming scan changes the scan_status by flushing the async
handlers after all invocations.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Check for both cfg->d0i3 and fw d0i3 support in order
to enable d0i3 support.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to solve races with sched_scan_stop, it is necessary
for the driver to be able to return an error to propagate that
to cfg80211 so it doesn't send an event.
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

NICs supported by iwldvm don't handle well TX AMPDU.
Disable it by default, still leave the possibility to
the user to force enable it with a debug parameter.

NICs supported by iwlmvm don't suffer from the same issue,
leave TX AMPDU enabled by default for these.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New FW enables support for power save on BSS and P2P client MACs
simultaneously when they function on different channels (DCM).
Enable this case in the driver after examining new TLV flag -
IWL_UCODE_TLV_FLAGS_BSS_P2P_PS_DCM. Still power management is not
allowed on both MACs if they function on a same channel.
Remove another redundant TLV flag - IWL_UCODE_TLV_FLAGS_P2P_PS that
is not in use anymore. Remove bound_vif_cnt as redundant.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This will allow to get sniffer captures with correct
settings for these HT / VHT capabilities.
Also set the corresponding HAVE_MCS / VHT_KNOWN bits in
the registration to mac80211.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There are a number of things in the .data section that should
really be in .rodata, for example all ops structs and strings.
Mark everything const that can be, leaving the .data section
pretty much empty.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The d3/d0i3 fw code requires the sta_id to be 0
(this is used to determine the rates and keys
to use in arp offloading).

Reserve sta_id 0 to station interface in order
to comply with this requirement.

Change some functions prototypes in order to
make the allocation function know about
the interface type.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>