Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The phy error mask registers are programmed already
in ath9k_ani_restart(), so there is no need to set them
in ath9k_ani_reset().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit, "ath9k_hw: improve ANI processing and rx desensitizing parameters"
removed code setting various phy registers holding threshold values.

This is likely required for OFDM weak signal detection to function
correctly, so add them, but skip AR9462 and AR9565.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit, "ath9k_hw: improve ANI processing and rx desensitizing parameters"
modified the immunity level tables for both CCK and OFDM. Fix them
so that the tables are in sync with the internal driver/codebase.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
changed various ANI operational parameters to address a specific
card/environment. This is not really applicable for other cards
in general usage.

As per internal documentation, lowering the immunity level can be
done only after 5 periods have passed and the CCK/OFDM errors are
below the low watermak threshold - which have been fixed at 300 and
400 respectively by the sytems team.

Raising the immunity level can be done when CCK/OFDM errors exceed
600 and 1000 (per second).

Set these values once during attach.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
changed the OFDM weak signal detection logic to disable it
for AP mode, which is not allowed. Fix this and enable it always
for AP mode.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.

An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191

Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.

Cc: stable@vger.kernel.org
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 68d9e1fa

This change reduces rx sensitivity with no apparent extra benefit.
It looks like it was meant for testing in a specific scenario,
but it was never properly validated.

Cc: rmanohar@qca.qualcomm.com
Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.

Cc: stable@vger.kernel.org
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ANI state can be maintained globally instead of per-channel.
This reduces memory usage and since default values are used
during a scan run, per-channel state is not required.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The macros ATH9K_ANI_USE_OFDM_WEAK_SIG can be removed.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The check "enable_ani" is not required since it is always
set to true and the logic for disabling/enabling ANI via
debugfs is done at a higher layer.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The only card with which WoW has been tested and verified is
AR9462. Do not enable it for all cards since WoW is really quirky
and needs to be tested properly with each chip.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Process and update the internal RSSI average, which
is used by ANI, after verifying that the received
frame has valid rate information.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch make use of STBC flag in DMA RX descriptor.
Only devices after ar9280 can provide this information.

If card support it we will set HAVE_STBC flag, to show
clint programm thet STBC is supported but not received.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

some flags used only outside of ath9k - In this case we can use
"enum mac80211_rx_flags" and pass it upstream without extra
conversation.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If any bins from the training data are skipped (i != max_index), the
calculated compensation curve gets distorted, and the signal will be
wildly overamplified. This may be the cause of the reported hardware
damage that was caused by PA predistortion (because of which PAPRD was
disabled by default).

When calculating the x_est, Y, theta values, the use of max_index and i
was reversed. i points to the bin index whereas max_index refers to the
index of the calculated arrays.

Note that PA predistortion is still disabled, it will be re-enabled
after it has been properly validated.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Accessing the OTP memory on AR9950 causes a data bus
like this:

  Data bus error, epc == 801f7774, ra == 801f7774
  Oops[#1]:
  CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.0-rc3 #592
  task: 87c28000 ti: 87c22000 task.ti: 87c22000
  $ 0   : 00000000 00000061 deadc0de 00000000
  $ 4   : b8115f18 00015f18 00000007 00000004
  $ 8   : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
  $12   : 7c7c3c7c 80320a68 00000000 7c7c7c3c
  $16   : 87cd8010 00015f18 00000007 00000000
  $20   : 00000064 00000004 87c23c7c 8035210c
  $24   : 00000000 801f3674
  $28   : 87c22000 87c23b48 00000001 801f7774
  Hi    : 00000000
  Lo    : 00000064
  epc   : 801f7774 ath9k_hw_wait+0x58/0xb0
      Not tainted
  ra    : 801f7774 ath9k_hw_wait+0x58/0xb0
  Status: 1000cc03 KERNEL EXL IE
  Cause : 4080801c
  PrId  : 00019750 (MIPS 74Kc)
  Modules linked in:
  Process swapper (pid: 1, threadinfo=87c22000, task=87c28000, ts=00000000)
  Stack : 0000000f 00000061 00002710 8006240c 00000001 87cd8010 87c23bb0 87cd8010
          00000000 00000004 00000003 80210c7c 000000b3 67fa8000 0000032a 000006fe
          000003e8 00000002 00000028 87c23bf0 000003ff 80210d24 803e5630 80210e28
          00000000 00000007 87cd8010 00007044 00000004 00000061 000003ff 000001ff
          87c26000 87cd8010 00000220 87cd8bb8 80210000 8020fcf4 87c22000 87c23c08
          ...
  Call Trace:
  [<801f7774>] ath9k_hw_wait+0x58/0xb0
  [<80210c7c>] ar9300_otp_read_word+0x80/0xd4
  [<80210d24>] ar9300_read_otp+0x54/0xb0
  [<8020fcf4>] ar9300_check_eeprom_header+0x1c/0x40
  [<80210fe4>] ath9k_hw_ar9300_fill_eeprom+0x118/0x39c
  [<80206650>] ath9k_hw_eeprom_init+0x74/0xb4
  [<801f96d0>] ath9k_hw_init+0x7ec/0x96c
  [<801e65ec>] ath9k_init_device+0x340/0x758
  [<801f35d0>] ath_ahb_probe+0x21c/0x2c0
  [<801c041c>] driver_probe_device+0xc0/0x1e4
  [<801c05ac>] __driver_attach+0x6c/0xa4
  [<801bea08>] bus_for_each_dev+0x64/0xa8
  [<801bfa40>] bus_add_driver+0xcc/0x24c
  [<801c0954>] driver_register+0xbc/0x17c
  [<803f8fc0>] ath9k_init+0x5c/0x88
  [<800608fc>] do_one_initcall+0xec/0x1a0
  [<803e6a68>] kernel_init_freeable+0x13c/0x200
  [<80309cdc>] kernel_init+0x1c/0xe4
  [<80062450>] ret_from_kernel_thread+0x10/0x18

On the AR9550, the OTP registers are located at
the same address as on the AR9340. Use the correct
values to avoid the error.

Cc: stable@vger.kernel.org  # 3.6+
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR934x v1.3 no longer needs the DCU backoff reduction workaround for
preventing rx overruns, but in turn needs the number of usable Tx
buffers to be reduced slightly.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a local bus timeout has been detected, the host interface needs to be
reset to clear the errors. AR934x uses a different synchronous interrupt
bit to indicate this, so the check needs to be fixed.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not subtract spur power from noise floor on this chip, as it can lead
to packet loss and other connectivity issues.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Chun-Yeow and Javier Lopez contributed these changes to
make mesh mode use the more similar AP beaconing mode and
queue parameters. Should improve PS performance, interface
concurrency (AP modes can coexist), and beacon interval
stability.

AR9271 (ath9k_htc) mesh interfaces also need to be in AP
operating mode.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Advertise support for management frame protection in hardware.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

More specifically, enable AP-style beaconing on mesh
ifaces and change the hw capabilities to reflect mesh
support.

Coexistence with a virtual STA interface was tested as
working fine.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
[rebase, add iface combinations]
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This was added during the early conversion of ampdu_action
to a sleeping callback. There is no need to do this - instead,
use the normal mutex that is acquired for all callbacks.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This option has not been enabled by default in any
distribution, has never been enabled in OpenWrt and no developer
has asked for this information in a bug report.

Dumping pages of random values doesn't help debugging,
remove this option (along with the vmalloc() abuse).
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Waiting for all subframes of an existing aggregation session to drain
before allowing mac80211 to start a new one is fragile and deadlocks
caused by this behavior have been observed.

Since mac80211 has proper synchronization for aggregation session
start/stop handling, a better approach to session handling is to simply
allow mac80211 to start a new session at any time. This requires
changing the code to discard any packets outside of the BlockAck window
in the A-MPDU software retry code.

This patch implements the above and also simplifies the code.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After a tx attempt, an A-MPDU subframe can still have fi->retries at 0
(if the retry count wasn't incremented due to powersave).
In that case it is still tracked as part of the block ack window, so
when draining the tid queue, its sequence number needs to be cleared
from the pending frame bitmap.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes some issues introduced in the rate control API rework.
When not running aggregation, copy bf->rates into info->control.rates
before applying the rate control status to it.
In ath_lookup_rate, the rates need to be pulled from bf->rates, not the
tx info.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When aggregation stop is requested, don't run the mac80211 aggregation
stop callback yet, while the session is still blocked.
Also, when aggregation flush is requested, don't run the callback at all.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Manual peak calibration is currently enabled only for
AR9462 and AR9565. This is also required for AR9485.
The initvals are also modified to disable HW peak calibration.

Cc: <stable@vger.kernel.org>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make sure that any open relayfs files are closed before
unregistering with mac80211, otherwise this crash is seen:

[ 1331.097846] BUG: unable to handle kernel paging request at 6b6b6b8b
[ 1331.098170] IP: [<c063d0d6>] debugfs_remove+0x26/0x80
[ 1331.098170] *pdpt = 000000002f9aa001 *pde = 0000000000000000
[ 1331.098170] Oops: 0000 [#1] PREEMPT SMP
[ 1331.098170] Modules linked in: iptable_raw xt_CT nf_conntrack_ipv4 nf_defrag]
[ 1331.098170] Pid: 4794, comm: rmmod Tainted: G        WC   3.9.1+ #5 To Be Fi.
[ 1331.098170] EIP: 0060:[<c063d0d6>] EFLAGS: 00010202 CPU: 0
[ 1331.098170] EIP is at debugfs_remove+0x26/0x80
[ 1331.098170] EAX: f2f3acd0 EBX: f2f3acd0 ECX: 00000006 EDX: f8622348
[ 1331.098170] ESI: 6b6b6b6b EDI: 00000001 EBP: ee251e14 ESP: ee251e0c
[ 1331.098170]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 1331.098170] CR0: 8005003b CR2: 6b6b6b8b CR3: 2e7b7000 CR4: 000007e0
[ 1331.098170] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 1331.098170] DR6: ffff0ff0 DR7: 00000400
[ 1331.098170] Process rmmod (pid: 4794, ti=ee250000 task=efaa2560 task.ti=ee25)
[ 1331.098170] Stack:
[ 1331.098170]  f241e170 0000000a ee251e1c f861394d ee251e28 c04e3088 f241e170 4
[ 1331.098170]  c04e30fe f45482b0 ee251e54 c04e3187 f25e86b0 ee251e54 f8618748 0
[ 1331.098170]  0000000a 00000001 ee251e68 f860065b f2509e20 f25085a0 f5b6e8a4 8
[ 1331.098170] Call Trace:
[ 1331.098170]  [<f861394d>] remove_buf_file_handler+0xd/0x20 [ath9k]
[ 1331.098170]  [<c04e3088>] relay_remove_buf+0x18/0x30
[ 1331.098170]  [<c04e30fe>] relay_close_buf+0x2e/0x40
[ 1331.098170]  [<c04e3187>] relay_close+0x77/0xf0
[ 1331.098170]  [<f8618748>] ? dpd_exit+0x38/0x40 [ath9k]
[ 1331.098170]  [<f860065b>] ath9k_deinit_softc+0x8b/0xa0 [ath9k]
[ 1331.098170]  [<f86006b8>] ath9k_deinit_device+0x48/0x60 [ath9k]
[ 1331.098170]  [<f86107f1>] ath_pci_remove+0x31/0x50 [ath9k]
[ 1331.098170]  [<c06dbff8>] pci_device_remove+0x38/0xc0
[ 1331.098170]  [<c079daa4>] __device_release_driver+0x64/0xc0
[ 1331.098170]  [<c079db97>] driver_detach+0x97/0xa0
[ 1331.098170]  [<c079cacc>] bus_remove_driver+0x6c/0xe0
[ 1331.098170]  [<c079c197>] ? bus_put+0x17/0x20
[ 1331.098170]  [<c079cae3>] ? bus_remove_driver+0x83/0xe0
[ 1331.098170]  [<c079e709>] driver_unregister+0x49/0x80
[ 1331.098170]  [<c06dc138>] pci_unregister_driver+0x18/0x80
[ 1331.098170]  [<f8610602>] ath_pci_exit+0x12/0x20 [ath9k]
[ 1331.098170]  [<f8619ce0>] ath9k_exit+0x17/0x337 [ath9k]
[ 1331.098170]  [<c09e537d>] ? mutex_unlock+0xd/0x10
[ 1331.098170]  [<c04bd36c>] sys_delete_module+0x17c/0x250
[ 1331.098170]  [<c0540dc4>] ? do_munmap+0x244/0x2d0
[ 1331.098170]  [<c0540e96>] ? vm_munmap+0x46/0x60
[ 1331.098170]  [<c09e8dc4>] ? restore_all+0xf/0xf
[ 1331.098170]  [<c09ebf50>] ? __do_page_fault+0x4c0/0x4c0
[ 1331.098170]  [<c04b18e4>] ? trace_hardirqs_on_caller+0xf4/0x180
[ 1331.098170]  [<c09ef28d>] sysenter_do_call+0x12/0x38
[ 1331.098170] Code: 90 8d 74 26 00 55 89 e5 83 ec 08 89 1c 24 89 74 24 04 3e 82
[ 1331.098170] EIP: [<c063d0d6>] debugfs_remove+0x26/0x80 SS:ESP 0068:ee251e0c
[ 1331.098170] CR2: 000000006b6b6b8b
[ 1331.727971] ---[ end trace b5bb9f2066cef7f9 ]---

Cc: <stable@vger.kernel.org>
Acked-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If NO_DMA=y:

drivers/built-in.o: In function `ath9k_beacon_generate':
drivers/net/wireless/ath/ath9k/beacon.c:146: undefined reference to `dma_unmap_single'
drivers/net/wireless/ath/ath9k/beacon.c:174: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/beacon.c:176: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath9k_beacon_remove_slot':
drivers/net/wireless/ath/ath9k/beacon.c:252: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_descdma_setup':
drivers/net/wireless/ath/ath9k/init.c:382: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_edma_get_buffers':
drivers/net/wireless/ath/ath9k/recv.c:616: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_get_next_rx_buf':
drivers/net/wireless/ath/ath9k/recv.c:740: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_edma_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:176: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:340: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_buf_link':
drivers/net/wireless/ath/ath9k/recv.c:122: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_tasklet':
drivers/net/wireless/ath/ath9k/recv.c:1275: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:1277: undefined reference to `dma_mapping_error'
drivers/net/wireless/ath/ath9k/recv.c:1283: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_init':
drivers/net/wireless/ath/ath9k/recv.c:226: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:229: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_rx_init':
drivers/net/wireless/ath/ath9k/recv.c:303: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:306: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_tx_complete_buf':
drivers/net/wireless/ath/ath9k/xmit.c:2088: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_txstatus_setup':
drivers/net/wireless/ath/ath9k/xmit.c:2344: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_tx_set_retry':
drivers/net/wireless/ath/ath9k/xmit.c:307: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_tx_setup_buffer':
drivers/net/wireless/ath/ath9k/xmit.c:1887: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/xmit.c:1889: undefined reference to `dma_mapping_error'
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Register Modification for xLNA board.
* TX gain table modification for zero calibration.
* AUX chain (LNA2) sensitivity enhancement
* Modify diversity bias default setting in INI.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a reset or a channel-change happens, for managed mode,
the HW beacon timers have to be programmed after the TSF has
been synchronized. This is handled via the sync flags.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If no keycache slots are available, ath_key_config can return -ENOSPC.
If the key index is not checked for errors, it can lead to logspam that
looks like this: "ath: wiphy0: keyreset: keycache entry 228 out of range"
This can cause follow-up errors if the invalid keycache index gets
used for tx.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>