The encoder .mode_fixup() operation is legacy, atomic updates uses the
new .atomic_check() operation. Convert the encoders drivers.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The atomic connector DPMS helper implements the connector DPMS operation
using atomic commit, removing the need for DPMS helper operations on
CRTCs and encoders.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

This removes the legacy mode config code. The CRTC and encoder prepare
and commit operations are not used anymore, remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

This removes the legacy plane update code. Wire up the default atomic
check and atomic commit mode config helpers as needed by the plane
update atomic helpers.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

When using atomic updates the CRTC .enable() and .disable() helper
operations are preferred over the (then legacy) .prepare() and .commit()
operations. Implement .enable() and rework .disable() to not depend on
DPMS, easing DPMS removal later on.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

When using atomic updates the encoder .enable() and .disable() helper
operations are preferred over the (then legacy) .prepare() and .commit()
operations. Implement .enable() and .disable() and rework .prepare(),
.commit() and .dpms() as wrappers around .enable() and .disable(),
easing their future removal.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

When using atomic updates the encoder .enable() and .disable() helper
operations are preferred over the (then legacy) .prepare() and .commit()
operations. Implement .enable() and .disable() and rework .prepare(),
.commit() and .dpms() as wrappers around .enable() and .disable(),
easing their future removal.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The LVDS encoder doesn't support DPMS states, replace the DPMS operation
by enable/disable to avoid propagating DPMS states down to the encoder
code.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The plane source and destination size and positions are stored in the
plane state, and a private copy is kept in the rcar_du_plane objects.
Remove the private copy as it just duplicates the state.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Hook up the default .reset(), .atomic_duplicate_state() and
.atomic_free_state() helpers to ensure that state objects are properly
created and destroyed, and call drm_mode_config_reset() at init time to
create the initial state objects.

Framebuffer reference count also gets maintained automatically by the
transitional helpers except for the legacy page flip operation. Maintain
it explicitly there.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Use the new CRTC atomic transitional helpers drm_helper_crtc_mode_set()
and drm_helper_crtc_mode_set_base() to implement the CRTC .mode_set and
.mode_set_base operations. This delegates primary plane configuration to
the plane .atomic_update and .atomic_disable operations, removing
duplicate code from the CRTC implementation.

There is now no code path available to the driver in which to drop the
reference to the CRTC acquired in the .prepare() operation if an error
then occurs. The driver thus now leaks a reference if an error occurs
during mode set. So be it, this will be fixed in a further step of the
atomic update transition.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Implement the CRTC .atomic_begin() and .atomic_flush() operations, the
plane .atomic_check(), .atomic_update() and operations, and use the
transitional atomic helpers to implement the plane update and disable
operations on top of the new atomic operations.

The plane setup code can't be moved out of the CRTC start function
completely yet, as the atomic code paths are not taken every time the
CRTC needs to be started. This results in some code duplication that
will be fixed after switching to atomic updates completely.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The hardware plane allocator loops over all planes to find free
candidates. However, instead of looping over the number of hardware
planes, it loops over the number of software planes, which happens to be
larger by one unit. This has no effect in practise as the extra plane is
always cleared in the mask of free planes, but it should still be fixed
for correctness.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Explicitly create the CRTC primary plane instead of relying on the core
helpers to do so. This simplifies the plane logic by merging the KMS and
software planes.

Reject plane API operations on the primary planes for now, as that code
will anyway be refactored when implementing support for atomic updates.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Let's avoid magic constants. Beside increasing code readability, it will
also ensure that no location will be forgotten when raising the maximum
number of groups, CRTCs or LVDS encoders
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

fbdev emulation requires at least one connector, and will fail to
initialize if no connector has been successfully instantiated. Disable
it in that case and print an informational message instead of failing
probe with a confusing fbdev emulation error message.

It could be argued that probe should fail when no connector is present,
but the DU could still be useful in that case with the to-be-implemented
memory write-back support.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The DRM core vblank handling mechanism requires drivers to forcefully
turn vblank reporting off when disabling the CRTC, and to restore the
vblank reporting status when enabling the CRTC.

Implement this using the drm_crtc_vblank_on/off helpers. When disabling
vblank we must first wait for page flips to complete, so implement page
flip completion wait as well.

Finally, drm_crtc_vblank_off() must be called at startup to synchronize
the state of the vblank core code with the hardware, which is initially
disabled. This is performed at CRTC creation time, requiring vertical
blanking to be initialized before creating CRTCs.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Turning a CRTC off will prevent a queued page flip from ever completing,
potentially confusing userspace. Wait for queued page flips to complete
before turning the CRTC off to avoid this.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The next commit will need functions to be reordered to avoid forward
declarations. Do it separately to help review.

This only moves functions without any change to the code.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The drm_connector encoder field points to the encoder driving the
connector. No such association exists at init time, as all pipelines are
disabled. Don't set the field.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The function is meant to restore the fbdev mode in the lastclose
handler, not to be called at init time. Remove the call.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

All encoders and CRTCs start disabled, re-disabling them is a no-op.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

With runtime PM the hw might still be off while doing the ->mode_set
callbacks - runtime PM get/put should only happen in the
enable/disable hooks to properly support DPMS. Which essentially makes
these callbacks useless for drivers support runtime PM, so make them
optional. Again motivated by discussions with Laurent.

Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

These names only make sense because of backwards compatability with
the order used by the crtc helper library. There's not really any real
requirement in the ordering here.

So rename them to something more descriptive and update the kerneldoc
a bit. Motivated in a discussion with Laurent about how to restore
plane state for dpms for drivers with runtime pm.

v2: Squash in fixup from Stephen Rothwell to fix a conflict with
tegra.

Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

The argument contains a pointer to the old state, rename it to old_state
like in all other commit helper functions.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This way drivers fully converted to atomic don't need to update these
legacy state variables in their modeset code any more.
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Atomic state handling adds a lot of indirection and complexity between
simple updates and drivers. For easier debugging the diagnostic output
is therefore rather chatty. Which is great for tracking down atomic
issues, but really annoying otherwise.

Add a new DRM_DEBUG_ATOMIC to be able to filter this out.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

The kerneldoc blocks for the drm_atomic_helper_*_set_property()
functions seem to have been copied from the plane disable handler
without being properly updated. Fix them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drm_crtc_vblank_get() is the new drm_vblank_get(), not the new
drm_vblank_off().
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Missing parameter when fetching the real voltage values
from atom.  Fixes problems with dynamic clocking on
certain boards.

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=87457Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Don't restrict it to just eDP panels.  Some LVDS bridge chips require
this.  Fixes blank panels on resume on certain laptops.  Noticed
by mrnuke on IRC.

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=42960Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Enable at init and disable on fini. Workaround for hardware problems.

v2 (chk): extend commit message
v3: add new function
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com> (v2)
Cc: stable@vger.kernel.org

Emit the EOP twice to avoid cache flushing problems.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Doing so can cause things to become slow.

Print a warning at compile time and an informative message at runtime in
that case.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88758
Cc: stable@vger.kernel.org
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

0-255 seems to be the preferred range for the pwm interface.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The efficient frequency (RPe) should stay in the range
RPn <= RPe <= RP0.  The pcode clamps the returned value
internally on Broadwell but not on Haswell.

Fix for missing range check in
commit 93ee2920
Author: Tom O'Rourke <Tom.O'Rourke@intel.com>
Date:   Wed Nov 19 14:21:52 2014 -0800

    drm/i915: Use efficient frequency for HSW/BDW

Reference: http://lists.freedesktop.org/archives/intel-gfx/2015-February/059802.htmlReported-by: NMichael Auchter <a@phire.org>
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org # v3.19
Signed-off-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Return IRQ_HANDLED from intel_dp_hpd_pulse() to properly
ignore the long HPD pulse on eDP to avoid the never ending
VDD off->HPD->VDD on->VDD off->HPD... cycle.

This fixes a regression intoduced by
 commit b2c5c181
 Author: Daniel Vetter <daniel.vetter@ffwll.ch>
 Date:   Fri Jan 23 06:00:31 2015 +0100

    drm/i915: Use symbolic irqreturn for ->hpd_pulse

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

This patch is based on exynos-drm-next branch of Inki Dae's tree at:
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos.git

DECON(Display and Enhancement Controller) is the new IP
in exynos7 SOC for generating video signals using pixel data.

DECON driver can be used to drive 2 different interfaces on Exynos7:
DECON-INT(video controller) and DECON-EXT(Mixer for HDMI)

The existing FIMD driver code was used as a template to create
DECON driver. Only DECON-INT is supported as of now, and
DECON-EXT support will be added later.

The current version of the driver supports video mode displays.

Changelog v2:
- Change config name, DRM_EXYNOS_DECON to DRM_EXYNOS7_DECON.
Signed-off-by: NAkshu Agrawal <akshua@gmail.com>
Signed-off-by: NAjay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

One bit in ->vm_flags is unused now!
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

LP_OUTPUT_HOLD is only in MIPI_PORT_CTRL(PORT_A) even for PORT_C in case
of dual link. In the dual link implementation, the bit is correctly set
or unset for hardcoded PORT_A, but for bit update the register base value
is read by using MIPI_PORT_CTRL(port) in a loop. The second iteration will
read base value from PORT_C and program for PORT_A. Mostly in case of dual
link all other bit values should be same, but logically we should read from
PORT_A. So hardcode to read initial value from PORT_A as well.
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>