- 30 1月, 2008 8 次提交
-
-
由 Ingo Molnar 提交于
temporary debugging - remove before this hits v2.6.25. Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
由 Yinghai Lu 提交于
empty_zero_page is in .bss section, and it is cleared in clear_bss by x86_64_start_kernel(). So don't clear that again in mem_init Signed-off-by: NYinghai Lu <yinghai.lu@sun.com> Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
由 Jeremy Fitzhardinge 提交于
It only has a single use, which can be trivially replaced. Signed-off-by: NJeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com> Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
由 Joerg Roedel 提交于
This patch does some whitespace cleanups in the paging code to fix some checkpatch.pl warnings of my formerly merged cleanup patches. Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com> Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
由 Joerg Roedel 提交于
This minor cleanup replaces _KERNPG_TABLE with the __PAGE_KERNEL* for 2MB PTEs in the 64-bit memory initialization code. The __PAGE_KERNEL* defines are more appropriate for PTEs. Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com> Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
由 Christoph Lameter 提交于
Use sparsemem as the only memory model for UP, SMP and NUMA. Measurements indicate that DISCONTIGMEM has a higher overhead than sparsemem. And FLATMEMs benefits are minimal. So I think its best to simply standardize on sparsemem. Results of page allocator tests (test can be had via git from slab git tree branch tests) Measurements in cycle counts. 1000 allocations were performed and then the average cycle count was calculated. Order FlatMem Discontig SparseMem 0 639 665 641 1 567 647 593 2 679 774 692 3 763 967 781 4 961 1501 962 5 1356 2344 1392 6 2224 3982 2336 7 4869 7225 5074 8 12500 14048 12732 9 27926 28223 28165 10 58578 58714 58682 (Note that FlatMem is an SMP config and the rest NUMA configurations) Memory use: SMP Sparsemem ------------- Kernel size: text data bss dec hex filename 3849268 397739 1264856 5511863 541ab7 vmlinux total used free shared buffers cached Mem: 8242252 41164 8201088 0 352 11512 -/+ buffers/cache: 29300 8212952 Swap: 9775512 0 9775512 SMP Flatmem ----------- Kernel size: text data bss dec hex filename 3844612 397739 1264536 5506887 540747 vmlinux So 4.5k growth in text size vs. FLATMEM. total used free shared buffers cached Mem: 8244052 40544 8203508 0 352 11484 -/+ buffers/cache: 28708 8215344 2k growth in overall memory use after boot. NUMA discontig: text data bss dec hex filename 3888124 470659 1276504 5635287 55fcd7 vmlinux total used free shared buffers cached Mem: 8256256 56908 8199348 0 352 11496 -/+ buffers/cache: 45060 8211196 Swap: 9775512 0 9775512 NUMA sparse: text data bss dec hex filename 3896428 470659 1276824 5643911 561e87 vmlinux 8k text growth. Given that we fully inline virt_to_page and friends now that is rather good. total used free shared buffers cached Mem: 8264720 57240 8207480 0 352 11516 -/+ buffers/cache: 45372 8219348 Swap: 9775512 0 9775512 The total available memory is increased by 8k. This patch makes sparsemem the default and removes discontig and flatmem support from x86. [ akpm@linux-foundation.org: allnoconfig build fix ] Acked-by: NAndi Kleen <ak@suse.de> Signed-off-by: NChristoph Lameter <clameter@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
由 Thomas Gleixner 提交于
More stuff shuffeled to the correct place Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NIngo Molnar <mingo@elte.hu>
-
由 Thomas Gleixner 提交于
Move them and fixup some users. Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NIngo Molnar <mingo@elte.hu>
-
- 30 11月, 2007 1 次提交
-
-
由 KAMEZAWA Hiroyuki 提交于
Changes __meminit to __init_refok. WARNING: vmlinux.o(.text+0x1d07c): Section mismatch: reference to .init.text:find_e820_area (between 'init_memory_mapping' and 'arch_add_memory') Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 30 10月, 2007 1 次提交
-
-
由 Linus Torvalds 提交于
This reverts commit 2e1c49db. First off, testing in Fedora has shown it to cause boot failures, bisected down by Martin Ebourne, and reported by Dave Jobes. So the commit will likely be reverted in the 2.6.23 stable kernels. Secondly, in the 2.6.24 model, x86-64 has now grown support for SPARSEMEM_VMEMMAP, which disables the relevant code anyway, so while the bug is not visible any more, it's become invisible due to the code just being irrelevant and no longer enabled on the only architecture that this ever affected. Reported-by: NDave Jones <davej@redhat.com> Tested-by: NMartin Ebourne <fedora@ebourne.me.uk> Cc: Zou Nan hai <nanhai.zou@intel.com> Cc: Suresh Siddha <suresh.b.siddha@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Acked-by: NAndy Whitcroft <apw@shadowen.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 17 10月, 2007 2 次提交
-
-
由 KAMEZAWA Hiroyuki 提交于
Now, arch dependent code around CONFIG_MEMORY_HOTREMOVE is a mess. This patch cleans up them. This is against 2.6.23-rc6-mm1. - fix compile failure on ia64/ CONFIG_MEMORY_HOTPLUG && !CONFIG_MEMORY_HOTREMOVE case. - For !CONFIG_MEMORY_HOTREMOVE, add generic no-op remove_memory(), which returns -EINVAL. - removed remove_pages() only used in powerpc. - removed no-op remove_memory() in i386, sh, sparc64, x86_64. - only powerpc returns -ENOSYS at memory hot remove(no-op). changes it to return -EINVAL. Note: Currently, only ia64 supports CONFIG_MEMORY_HOTREMOVE. I welcome other archs if there are requirements and testers. Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Christoph Lameter 提交于
x86_64 uses 2M page table entries to map its 1-1 kernel space. We also implement the virtual memmap using 2M page table entries. So there is no additional runtime overhead over FLATMEM, initialisation is slightly more complex. As FLATMEM still references memory to obtain the mem_map pointer and SPARSEMEM_VMEMMAP uses a compile time constant, SPARSEMEM_VMEMMAP should be superior. With this SPARSEMEM becomes the most efficient way of handling virt_to_page, pfn_to_page and friends for UP, SMP and NUMA on x86_64. [apw@shadowen.org: code resplit, style fixups] [apw@shadowen.org: vmemmap x86_64: ensure end of section memmap is initialised] Signed-off-by: NChristoph Lameter <clameter@sgi.com> Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Acked-by: NMel Gorman <mel@csn.ul.ie> Cc: Andi Kleen <ak@suse.de> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 11 10月, 2007 2 次提交
-
-
由 Thomas Gleixner 提交于
Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NIngo Molnar <mingo@elte.hu>
-
由 Thomas Gleixner 提交于
Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NIngo Molnar <mingo@elte.hu>
-
- 27 7月, 2007 1 次提交
-
-
由 Linus Torvalds 提交于
This reverts most of commit 19d36ccd. The way to DEBUG_RODATA interactions with KPROBES and CPU hotplug is to just not mark the text as being write-protected in the first place. Both of those facilities depend on rewriting instructions. Having "helpful" debug facilities that just cause more problem is not being helpful. It just adds complexity and bugs. Not worth it. Reported-by: NRafael J. Wysocki <rjw@sisk.pl> Cc: Andi Kleen <ak@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 23 7月, 2007 4 次提交
-
-
由 Sam Ravnborg 提交于
Fix following warning: WARNING: vmlinux.o(.text+0x188ea): Section mismatch: reference to .init.text:__alloc_bootmem_core (between 'alloc_bootmem_high_node' and 'get_gate_vma') alloc_bootmem_high_node() is only used from __init scope so declare it __init. And in addition declare the weak variant __init too. Signed-off-by: NSam Ravnborg <sam@ravnborg.org> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andi Kleen 提交于
Reenable kprobes and alternative patching when the kernel text is write protected by DEBUG_RODATA Add a general utility function to change write protected text. The new function remaps the code using vmap to write it and takes care of CPU synchronization. It also does CLFLUSH to make icache recovery faster. There are some limitations on when the function can be used, see the comment. This is a newer version that also changes the paravirt_ops code. text_poke also supports multi byte patching now. Contains bug fixes from Zach Amsden and suggestions from Mathieu Desnoyers. Cc: Jan Beulich <jbeulich@novell.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org> Cc: Zach Amsden <zach@vmware.com> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
This patch uses the read and write functions provided at system.h for control registers instead of writting raw assembly over and over again in .c files. Functions to manipulate cr2 and cr8 were provided, as they were lacking. Also, removed some extra space after closing brackets Signed-off-by: NGlauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
This patch makes the i386 behave the same way that x86_64 does when a segfault happens. A line gets printed to the kernel log so that tools that need to check for failures can behave more uniformly between debug.show_unhandled_signals sysctl variable to 0 (or by doing echo 0 > /proc/sys/debug/exception-trace) Also, all of the lines being printed are now using printk_ratelimit() to deny the ability of DoS from a local user with a program like the following: main() { while (1) if (!fork()) *(int *)0 = 0; } This new revision also includes the fix that Andrew did which got rid of new sysctl that was added to the system in earlier versions of this. Also, 'show-unhandled-signals' sysctl has been renamed back to the old 'exception-trace' to avoid breakage of people's scripts. AK: Enabling by default for i386 will be likely controversal, but let's see what happens AK: Really folks, before complaining just fix your segfaults AK: I bet this will find a lot of silent issues Signed-off-by: NMasoud Sharbiani <masouds@google.com> Signed-off-by: NAndi Kleen <ak@suse.de> [ Personally, I've found the complaints useful on x86-64, so I'm all for this. That said, I wonder if we could do it more prettily.. -Linus ] Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 22 7月, 2007 2 次提交
-
-
由 Jan Beulich 提交于
Signed-off-by: NJan Beulich <jbeulich@novell.com> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andi Kleen 提交于
This implements new vDSO for x86-64. The concept is similar to the existing vDSOs on i386 and PPC. x86-64 has had static vsyscalls before, but these are not flexible enough anymore. A vDSO is a ELF shared library supplied by the kernel that is mapped into user address space. The vDSO mapping is randomized for each process for security reasons. Doing this was needed for clock_gettime, because clock_gettime always needs a syscall fallback and having one at a fixed address would have made buffer overflow exploits too easy to write. The vdso can be disabled with vdso=0 It currently includes a new gettimeofday implemention and optimized clock_gettime(). The gettimeofday implementation is slightly faster than the one in the old vsyscall. clock_gettime is significantly faster than the syscall for CLOCK_MONOTONIC and CLOCK_REALTIME. The new calls are generally faster than the old vsyscall. Advantages over the old x86-64 vsyscalls: - Extensible - Randomized - Cleaner - Easier to virtualize (the old static address range previously causes overhead e.g. for Xen because it has to create special page tables for it) Weak points: - glibc support still to be written The VM interface is partly based on Ingo Molnar's i386 version. Includes compile fix from Joachim Deguara Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 22 6月, 2007 1 次提交
-
-
由 Arjan van de Ven 提交于
Do not mark the kernel text read only if KPROBES is in the kernel; kprobes needs to hot-patch the kernel text to insert it's instrumentation. In this case, only mark the .rodata segment as read only. Signed-off-by: NArjan van de Ven <arjan@linux.intel.com> Tested-by: NS. P. Prasanna <prasanna@in.ibm.com> Cc: Andi Kleen <ak@suse.de> Cc: William Cohen <wcohen@redhat.com> Cc: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 09 6月, 2007 1 次提交
-
-
由 Bob Picco 提交于
We aren't sampling for holes in memory. Thus we encounter a section hole with empty section map pointer for SPARSEMEM and OOPs for show_mem. This issue has been seen in 2.6.21, current git and current mm. The patch below is for mainline and mm. It was boot tested for SPARSEMEM, current VMEMMAP of Andy's in mm ml and DISCONTIGMEM. A slightly different patch will be posted to stable for 2.6.21. Previous to commit f0a5a58a memory_present was called for node_start_pfn to node_end_pfn. This would cover the hole(s) with reserved pages and valid sections. Most SPARSEMEM supported arches do a pfn_valid check in show_mem before computing the page structure address. This issue was brought to my attention on IRC by Arnaldo Carvalho de Melo. Thanks to Arnaldo for testing. Signed-off-by: NBob Picco <bob.picco@hp.com> Cc: Chuck Ebbert <cebbert@redhat.com> Cc: Andi Kleen <ak@suse.de> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Acked-by: NAndy Whitcroft <apw@shadowen.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 01 6月, 2007 1 次提交
-
-
由 Zou Nan hai 提交于
On systems with huge amount of physical memory, VFS cache and memory memmap may eat all available system memory under 4G, then the system may fail to allocate swiotlb bounce buffer. There was a fix for this issue in arch/x86_64/mm/numa.c, but that fix dose not cover sparsemem model. This patch add fix to sparsemem model by first try to allocate memmap above 4G. Signed-off-by: NZou Nan hai <nanhai.zou@intel.com> Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com> Cc: Andi Kleen <ak@suse.de> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 09 5月, 2007 1 次提交
-
-
由 Yasunori Goto 提交于
This is to fix many section mismatches of code related to memory hotplug. I checked compile with memory hotplug on/off on ia64 and x86-64 box. Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 07 5月, 2007 1 次提交
-
-
由 Linus Torvalds 提交于
This was broken. It adds complexity, for no good reason. Rather than separate __pa() and __pa_symbol(), we should deprecate __pa_symbol(), and preferably __pa() too - and just use "virt_to_phys()" instead, which is more readable and has nicer semantics. However, right now, just undo the separation, and make __pa_symbol() be the exact same as __pa(). That fixes the bugs this patch introduced, and we can do the fairly obvious cleanups later. Do the new __phys_addr() function (which is now the actual workhorse for the unified __pa()/__pa_symbol()) as a real external function, that way all the potential issues with compile/link-time optimizations of constant symbol addresses go away, and we can also, if we choose to, add more sanity-checking of the argument. Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@in.ibm.com> Cc: Andi Kleen <ak@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 03 5月, 2007 6 次提交
-
-
由 Konrad Rzeszutek 提交于
This patch touches the NMI watchdog every MAX_ORDER_NR_PAGES to inhibit the machine from triggering an NMI while the CPUs are locked. This situation is happening on boxes with more than 64CPUs and 128GB of RAM when Alt-SysRq-m is performed. It has been succesfully tested for regression on uni, 2, 4, 8 32, and 64 CPU boxes with various memory configuration. Signed-off-by: NAndi Kleen <ak@suse.de>
-
由 Jan Beulich 提交于
On x86-64, kernel memory freed after init can be entirely unmapped instead of just getting 'poisoned' by overwriting with a debug pattern. On i386 and x86-64 (under CONFIG_DEBUG_RODATA), kernel text and bug table can also be write-protected. Compared to the first version, this one prevents re-creating deleted mappings in the kernel image range on x86-64, if those got removed previously. This, together with the original changes, prevents temporarily having inconsistent mappings when cacheability attributes are being changed on such pages (e.g. from AGP code). While on i386 such duplicate mappings don't exist, the same change is done there, too, both for consistency and because checking pte_present() before using various other pte_XXX functions is a requirement anyway. At once, i386 code gets adjusted to use pte_huge() instead of open coding this. AK: split out cpa() changes Signed-off-by: NJan Beulich <jbeulich@novell.com> Signed-off-by: NAndi Kleen <ak@suse.de>
-
由 Vivek Goyal 提交于
Currently __pa_symbol is for use with symbols in the kernel address map and __pa is for use with pointers into the physical memory map. But the code is implemented so you can usually interchange the two. __pa which is much more common can be implemented much more cheaply if it is it doesn't have to worry about any other kernel address spaces. This is especially true with a relocatable kernel as __pa_symbol needs to peform an extra variable read to resolve the address. There is a third macro that is added for the vsyscall data __pa_vsymbol for finding the physical addesses of vsyscall pages. Most of this patch is simply sorting through the references to __pa or __pa_symbol and using the proper one. A little of it is continuing to use a physical address when we have it instead of recalculating it several times. swapper_pgd is now NULL. leave_mm now uses init_mm.pgd and init_mm.pgd is initialized at boot (instead of compile time) to the physmem virtual mapping of init_level4_pgd. The physical address changed. Except for the for EMPTY_ZERO page all of the remaining references to __pa_symbol appear to be during kernel initialization. So this should reduce the cost of __pa in the common case, even on a relocated kernel. As this is technically a semantic change we need to be on the lookout for anything I missed. But it works for me (tm). Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Signed-off-by: NVivek Goyal <vgoyal@in.ibm.com> Signed-off-by: NAndi Kleen <ak@suse.de>
-
由 Vivek Goyal 提交于
With the rewrite of the SMP trampoline and the early page allocator there is nothing that needs identity mapped pages, once we start executing C code. So add zap_identity_mappings into head64.c and remove zap_low_mappings() from much later in the code. The functions are subtly different thus the name change. This also kills boot_level4_pgt which was from an earlier attempt to move the identity mappings as early as possible, and is now no longer needed. Essentially I have replaced boot_level4_pgt with trampoline_level4_pgt in trampoline.S Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Signed-off-by: NVivek Goyal <vgoyal@in.ibm.com> Signed-off-by: NAndi Kleen <ak@suse.de>
-
由 Vivek Goyal 提交于
Early in the boot process we need the ability to set up temporary mappings, before our normal mechanisms are initialized. Currently this is used to map pages that are part of the page tables we are building and pages during the dmi scan. The core problem is that we are using the user portion of the page tables to implement this. Which means that while this mechanism is active we cannot catch NULL pointer dereferences and we deviate from the normal ways of handling things. In this patch I modify early_ioremap to map pages into the kernel portion of address space, roughly where we will later put modules, and I make the discovery of which addresses we can use dynamic which removes all kinds of static limits and remove the dependencies on implementation details between different parts of the code. Now alloc_low_page() and unmap_low_page() use early_iomap() and early_iounmap() to allocate/map and unmap a page. Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Signed-off-by: NVivek Goyal <vgoyal@in.ibm.com> Signed-off-by: NAndi Kleen <ak@suse.de>
-
由 Stephen Hemminger 提交于
The dma_ops structure can be const since it never changes after boot. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NAndi Kleen <ak@suse.de>
-
- 15 2月, 2007 3 次提交
-
-
由 Eric W. Biederman 提交于
The semantic effect of insert_at_head is that it would allow new registered sysctl entries to override existing sysctl entries of the same name. Which is pain for caching and the proc interface never implemented. I have done an audit and discovered that none of the current users of register_sysctl care as (excpet for directories) they do not register duplicate sysctl entries. So this patch simply removes the support for overriding existing entries in the sys_sysctl interface since no one uses it or cares and it makes future enhancments harder. Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Acked-by: NRalf Baechle <ralf@linux-mips.org> Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Howells <dhowells@redhat.com> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Andi Kleen <ak@muc.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Corey Minyard <minyard@acm.org> Cc: Neil Brown <neilb@suse.de> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: James Bottomley <James.Bottomley@steeleye.com> Cc: Jan Kara <jack@ucw.cz> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: Mark Fasheh <mark.fasheh@oracle.com> Cc: David Chinner <dgc@sgi.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Eric W. Biederman 提交于
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Acked-by: NAndi Kleen <ak@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Eric W. Biederman 提交于
The only sysctl x86_64 provides are not provided elsewhere, so insert_at_head is unnecessary. Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Acked-by: NAndi Kleen <ak@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 07 12月, 2006 1 次提交
-
-
由 Ernie Petrides 提交于
The final line of /proc/<pid>/maps on x86_64 for native 64-bit tasks shows an incorrect ending address and incorrect permissions. There is only a single page mapped in this vsyscall region, and it is accessible for both read and execute. The patch below fixes this. (Since 32-bit-compat tasks have a real vma with correct perms/range, no change is necessary for that scenario.) Before the patch, a "cat /proc/self/maps | tail -1" shows this: ffffffffff600000-ffffffffffe00000 ---p 00000000 [...] After the patch, this is the output: ffffffffff600000-ffffffffff601000 r-xp 00000000 [...] Signed-off-by: NErnie Petrides <petrides@redhat.com> Signed-off-by: NAndi Kleen <ak@suse.de>
-
- 21 11月, 2006 1 次提交
-
-
由 Yasunori Goto 提交于
This is to fix compile error of x86-64 memory hotplug without any NUMA option. CC arch/x86_64/mm/init.o arch/x86_64/mm/init.c:501: error: redefinition of 'memory_add_physaddr_to_nid' include/linux/memory_hotplug.h:71: error: previous definition of 'memory_add_phys addr_to_nid' was here arch/x86_64/mm/init.c:509: error: redefinition of 'memory_add_physaddr_to_nid' arch/x86_64/mm/init.c:501: error: previous definition of 'memory_add_physaddr_to_ nid' was here I confirmed compile completion with !NUMA, (NUMA & !ACPI_NUMA), or (NUMA & ACPI_NUMA). Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com> Acked-by: NAndi Kleen <ak@suse.de> Cc: "Randy.Dunlap" <rdunlap@xenotime.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 14 11月, 2006 1 次提交
-
-
由 Andi Kleen 提交于
This can happen on kexec kernels with some configurations, in particularly on Unisys ES7000 systems. Analysis by Amul Shah Cc: Amul Shah <amul.shah@unisys.com> Signed-off-by: NAndi Kleen <ak@suse.de>
-
- 12 10月, 2006 1 次提交
-
-
由 Mel Gorman 提交于
Arch-independent zone-sizing is using indices instead of symbolic names to offset within an array related to zones (max_zone_pfns). The unintended impact is that ZONE_DMA and ZONE_NORMAL is initialised on powerpc instead of ZONE_DMA and ZONE_HIGHMEM when CONFIG_HIGHMEM is set. As a result, the the machine fails to boot but will boot with CONFIG_HIGHMEM turned off. The following patch properly initialises the max_zone_pfns[] array and uses symbolic names instead of indices in each architecture using arch-independent zone-sizing. Two users have successfully booted their powerpcs with it (one an ibook G4). It has also been boot tested on x86, x86_64, ppc64 and ia64. Please merge for 2.6.19-rc2. Credit to Benjamin Herrenschmidt for identifying the bug and rolling the first fix. Additional credit to Johannes Berg and Andreas Schwab for reporting the problem and testing on powerpc. Signed-off-by: NMel Gorman <mel@csn.ul.ie> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 01 10月, 2006 1 次提交
-
-
由 Keith Mannthey 提交于
The api for hot-add memory already has a construct for finding nodes based on an address, memory_add_physaddr_to_nid. This patch allows the fucntion to do something besides return 0. It uses the nodes_add infomation to lookup to node info for a hot add event. Signed-off-by: NKeith Mannthey <kmannth@us.ibm.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Andi Kleen <ak@muc.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-