OpRegion event on 965G requires legacy BLC event enabled in pipe stat. As LVDS
could be on either pipe now, we should enable BLC event on both pipe. If fail to
do so, we couldn't handle the brightness request triggered from graphics
opregion.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Based on a patch by Zhao Yakui.
Signed-off-by: NEric Anholt <eric@anholt.net>

The gen4 docs say it works, so why not.  Tested on Ironlake.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This was brought over from UMS, and used for a while until we decided
that drm_helper_resume_force_mode was easier and more reliable, since
it didn't require duplicating all the code deleted here.  We just
forgot to delete all that junk for a while.

This one replaces original param for intel_ddc_get_modes() with
DRM connector and i2c bus adapter instead. With explicit params,
we won't require that a single driver structure must hold connector
and DDC bus reference, which ease the conversion to splitted encoder/
connector model.

It also clears up for some cases that we would steal other DDC bus
for mode probe, like VGA analog DDC probe for DVI-I. Also it fixed
a bug in old DVI-I probe handling, that failed to restore origin
analog GPIO port.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

In load detection, connector's encoder assignment must be kept
consistent for proper mode setting, and this makes connector as
explicit parameter for load detect function to not require single
data structure to hold both encoder and connector reference, ease
the transition for splitted encoder/connector model.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

For introducing splitted encoder/connector structure, this helper will return
connector's attached encoder when needed.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This adds new structure of intel_connector to present drm's
connector object, which is used to convert from origin single
output into encoder/connector model.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

What we really want is encoder info instead of connector, so change
some more list walk in pipeline setup functions from connector_list
to encoder_list.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Instead of walking through drm connector_list uses encoder_list
for calling hotplug functions which is consistent with intel display
hotplug reporting.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Use DECLARE_EVENT_CLASS to remove duplicate code:

   text    data     bss     dec     hex filename
  14655    2732      15   17402    43fa i915_trace_points.o.orig
  11625    2732      10   14367    381f i915_trace_points.o

8 events are converted:

  i915_gem_object:  i915_gem_object_{unbind, destroy}
  i915_gem_request: i915_gem_request_{complete, retire, wait_begin, wait_end}
  i915_ring:        i915_ring_{wait_begin, wait_end}

No functional change.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

The TV detection logic is not reliable on the Cantiga platform.
Sometimes the TV will be misdetected as the following two cases:
- TV is misdetected on some laptops. e.g. There is no TV connector
port or no TV is attached. But the TV is shown as connected.
- TV connector type is misdetected. e.g. the component TV is
attached, but the TV is shown as S-video type.

According to the hardware requirement, the TV sense state bits of TV DAC
register should be cleared to zero on Cantiga platfrom.

https://bugzilla.kernel.org/show_bug.cgi?id=14792

Cc: Stable Team <stable@kernel.org>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Tested-by: NSanti <santi@agolina.net>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This trys to shut up complains about invalid LVDS EDID during
mode probe, but uses fixed panel mode directly for panels with
broken EDID.

https://bugs.freedesktop.org/show_bug.cgi?id=23099
https://bugs.freedesktop.org/show_bug.cgi?id=26395Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Tested-by: NSitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

BugLink: http://bugs.launchpad.net/ubuntu/bugs/544671

This system claims to have a LVDS but has not.
Signed-off-by: NStephane Graber <stgraber@ubuntu.com>
Signed-off-by: NStefan Bader <stefan.bader@canonical.com>
CC: stable@kernel.org
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NEric Anholt <eric@anholt.net>

The intel_output naming is inherited from the UMS code, which had a
structure of screen -> CRTC -> output.  The DRM code has an additional
notion of encoder/connector, so the structure is screen -> CRTC ->
encoder -> connector.  This is a useful structure for SDVO encoders
which can support multiple connectors (each of which requires
different programming in the one encoder and could be connected to
different CRTCs), or for DVI-I, where multiple encoders feed into the
connector for whether it's used for digital or analog.  Most of our
code is encoder-related, so transition it to talking about encoders
before we start trying to distinguish connectors.

This patch is produced by sed s/intel_output/intel_encoder/ over the
driver.
Signed-off-by: NEric Anholt <eric@anholt.net>

... not a GTT driver. So the additional chipset flush introduced in

commit 2162e6a2
Author: Dave Airlie <airlied@redhat.com>
Date:   Wed Nov 21 16:36:31 2007 +1000

    agp/intel: Add chipset flushing support for i8xx chipsets.

to fix a GTT problem makes absolutely no sense. If this would really be needed
for AGP chipsets, too, we should add it to all i8xx agp drivers, not just one.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

This is a purely cosmetic change to make changes in this area easier.
And hey, it's not only clearer and typechecked, but actually shorter,
too!

[anholt: To clarify, this is a change to let us later make
drm_i915_gem_object subclass drm_gem_object, instead of having
drm_gem_object have a pointer to i915's private data]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

It is causing hangs after a suspend/resume cycle with the default
powersave=1 module option on these chipsets since 2.6.32-rc.

BugLink: http://bugs.launchpad.net/bugs/492392Signed-off-by: NRobert Hooker <sarvatt@ubuntu.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux:
  OMAP: DSS2: panel-generic: re-implement mode changing
  OMAP: DSS2: initialize dss clk sources properly
  OMAP: DSS2: VRAM: Fix early_param for vram

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] Orion5x: replace KEY_WLAN with KEY_WPS_BUTTON
  [ARM] Kirkwood: WPS button keycode mapping
  pxa168fb: fix incorrect resource calculation
  [ARM] pxa/raumfeld: fix button name
  [ARM] pxa/raumfeld: remove duplicated #include
  [ARM] locomo: fix unpaired spin_lock_irqsave
  [ARM] locomo: fix SPI register offset
  [ARM] pxa/sharpsl: add dependency of max1111 driver to sharpsl_pm
  [ARM] pxa: remove unnecessary 'select FB_W100' from some platforms
  [ARM] pxa: remove spi cs gpio direction to avoid clash with driver
  [ARM] mmp: fix for variables in uncompress.h being discarded
  [ARM] pxa: fix for variables in uncompress.h being discarded
  ARM: Update mach-types
  ARM: Fix IXP23xx build error in mach/memory.h

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: don't try to decode GETATTR if DELEGRETURN returned error
  sunrpc: handle allocation errors from __rpc_lookup_create()
  SUNRPC: Fix the return value of rpc_run_bc_task()
  SUNRPC: Fix a use after free bug with the NFSv4.1 backchannel
  SUNRPC: Fix a potential memory leak in auth_gss
  NFS: Prevent another deadlock in nfs_release_page()

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata-sff: fix spurious IRQ handling
  pata_via: Add VIA VX900 support

* 'sh/for-2.6.34' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Silence unintialized variable warnings in dwarf unwinder.
  sh: Tidy up a couple of section mismatches.
  sh: Fix build after dynamic PMB rework
  sh: Replace unsafe manipulation of MMUCR
  sh: Flush ITLB too in PTEAEX's flush_tlb_page()
  sh64: Remove long unused mid_sched macro
  SH: remove superfluous warning from the serial driver
  SH: fix SCIFA SCASCR register bit definitions
  serial: sh-sci: fix SH-Mobile SH breakage
  sh: Add watch-dog register address for SH7722/SH7723/SH7724
  sh: ms7724: Add tiny-document for sound
  sh: mach-ecovec24: Add i2c_put_adapter on sh_eth_init

Sparse complained about this missing spin_unlock()
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: fix dangling pointers
  lp3971: Fix BUCK_VOL_CHANGE_SHIFT logic
  lp3971: Fix setting val for LDO2 and LDO4
  regulator: Get rid of lockdep warning
  regulator: handle kcalloc() failure
  Regulators: max8925-regulator - clean up driver data after removal

do_sync_read/write() should set kiocb.ki_nbytes to be consistent with
do_sync_readv_writev().
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix an incorrect for-loop in elf_core_vma_data_size().  The advance-pointer
statement lacks an assignment:

	  CC      fs/binfmt_elf_fdpic.o
	fs/binfmt_elf_fdpic.c: In function 'elf_core_vma_data_size':
	fs/binfmt_elf_fdpic.c:1593: warning: statement with no effect
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: Stop trying to use ACPI lid status to determine LVDS connection.
  drm/intel: fix up set_tiling for untiled->tiled transition
  drm/i915: Set up the documented clock gating on Sandybridge and Ironlake.
  agp/intel: Don't do the chipset flush on Sandybridge.
  agp/intel: Respect the GTT size on Sandybridge for scratch page setup.
  drm/i915: fix small leak on overlay error path
  drm/i915: Avoid NULL deref in get_pages() unwind after error.
  drm/i915: Fix check with IS_GEN6
  drivers/gpu/drm/i915/intel_bios.c: fix continuation line formats
  drm/i915: Enable VS timer dispatch.
  drm/i915: Rename FBC_C3_IDLE to FBC_CTL_C3_IDLE to match other registers
  drm/i915: remove an unnecessary wait_request()
  drm/i915: Don't bother with the BKL for GEM ioctls.

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-scmi: Provide module aliases for automatic loading
  i2c-scmi: Support IBM SMBus CMI devices
  acpi: Support IBM SMBus CMI devices

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] fix boot failures with compressed kernels
  [S390] fix broken proc interface for sclp_async
  [S390] sclp: avoid 64 bit division
  [S390] dasd: check tsb validity
  [S390] dasd: fix alignment of transport mode recovery TCW
  [S390] system.h: Fix compile error for 1 and 2 byte cmpxchg
  [S390] smp: fix lowcore allocation
  [S390] zcore: CPU registers are not saved under LPAR

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: cmipci: work around invalid PCM pointer
  ASoC: Remove BROKEN from i.MX audio after dependencies merged
  ALSA: hda - Fix access-after-free in patch_realtek.c
  ALSA: hda - Sort codec entry list of Nvidia HDMI
  ALSA: hda - Add support of Nvidia GT220 HDMI
  ALSA: hda: Fix 0 dB offset for HP laptops using CX20551 (Waikiki)
  ALSA: hda - Add PCI quirk for HP dv6-1110ax.
  sound/oss/vidc.c: change the field used with DMA_ACTIVE
  ASoC: pxa-pcm-lib: initialize DMA channel to -1
  ASoC: Bail out of wm_hubs DC servo if calibration fails
  ASoC: tlv320dac33: Internal clocking changes
  ASoC: tlv320dac33: Fix DSP modes
  ASoC: SIU driver shall select FW_LOADER

Document the circular buffering capabilities available in Linux.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: NRandy Dunlap <rdunlap@xenotime.net>
Reviewed-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Smaller size than a minimum blocksize can't be used, after all it's
handled like 0 size.

For extended partition itself, this makes sure to use bigger size than one
logical sector size at least.
Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Daniel Taylor <Daniel.Taylor@wdc.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In order to use disks larger than 2TiB on Windows XP, it is necessary to
use 4096-byte logical sectors in an MBR.

Although the kernel storage and functions called from msdos.c used
"sector_t" internally, msdos.c still used u32 variables, which results in
the ability to handle XP-compatible large disks.

This patch changes the internal variables to "sector_t".

Daniel said: "In the near future, WD will be releasing products that need
this patch".

[hirofumi@mail.parknet.co.jp: tweaks and fix]
Signed-off-by: NDaniel Taylor <daniel.taylor@wdc.com>
Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixup for the flatpanel output.  The geode_modedb attribute flags are used
to set the SYNC polarity of the flatpanel.  Without this patch our
flatpanel registers stayed unconfigured, so we just saw garbage output.
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"m" is never NULL here.  We need a different test for the end of list
condition.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: NWANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Discovered while testing other mempolicy changes:

get_mempolicy() does not handle static/relative mode flags correctly.
Return the value that the user specified so that it can be restored
via set_mempolicy() if desired.
Signed-off-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Ravikiran Thirumalai <kiran@scalex86.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the extended CSD register the CARD_TYPE is an 8-bit value of which the
upper 6 bits were reserved in JEDEC specifications prior to version 4.4.
In version 4.4 two of the reserved bits were designated for identifying
support for the newly added High-Speed Dual Data Rate.  Unfortunately the
mmc_read_ext_csd() function required that the reserved bits be zero
instead of ignoring them as it should.

This patch makes mmc_read_ext_csd() ignore the CARD_TYPE bits that are
reserved or not yet supported.  It also stops the function jumping to the
end as though an error occurred, when it is only warns that the CARD_TYPE
bits (that it does interpret) are invalid.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The reiserfs journal behaves inconsistently when determining whether to
allow a mount of a read-only device.

This is due to the use of the continue_replay variable to short circuit
the journal scanning.  If it's set, it's assumed that there are
transactions to replay, but there may not be.  If it's unset, it's assumed
that there aren't any, and that may not be the case either.

I've observed two failure cases:
1) Where a clean file system on a read-only device refuses to mount
2) Where a clean file system on a read-only device passes the
   optimization and then tries writing the journal header to update
   the latest mount id.

The former is easily observable by using a freshly created file system on
a read-only loopback device.

This patch moves the check into journal_read_transaction, where it can
bail out before it's about to replay a transaction.  That way it can go
through and skip transactions where appropriate, yet still refuse to mount
a file system with outstanding transactions.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>