When userspace asks whether the driver supports the BLT or BSD rings for
this chip, simply report whether those particular rings are initialised

v2: Use intel_ring_initialized()
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rather than use the magic feature tests HAS_BLT/HAS_BSD just check
whether the ring we are about to dispatch the execbuffer on is
initialised.

v2: Use intel_ring_initialized()
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In many places we wish to iterate over the rings associated with the
GPU, so refactor them to use a common macro.

Along the way, there are a few code removals that should be side-effect
free and some rearrangement which should only have a cosmetic impact,
such as error-state.

Note that this slightly changes the semantics in the hangcheck code:
We now always cycle through all enabled rings instead of
short-circuiting the logic.

v2: Pull in a couple of suggestions from Ben and Daniel for
intel_ring_initialized() and not removing the warning (just moving them
to a new home, closer to the error).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Added note to commit message about the small behaviour
change, suggested by Ben Widawsky.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Inspired by a recent regression that seems to confuse pch transcoder
state, let's be a bit more paranoid.

References: https://bugs.freedesktop.org/show_bug.cgi?id=49712
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Pimped commit message.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch enables i915 driver to handle Haswell devices. It should go in
last, when things are working stable enough.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Haswell, we need to properly train the DDI buffers prior to enabling
HDMI, and enable the required clocks with correct dividers for the desired
frequency.

Also, we cannot simple reuse HDMI routines from previous generations of
GPU, as most of HDMI-specific stuff is being done via the DDI port
programming instead of HDMI-specific registers.

This commit take advantage of the WR PLL clock table which is in a
separate (previous) commit to select the right divisors for each mode.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move intel_hdmi data structure and support functions to a shared location,
to allow their usage from intel_ddi module.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This table is used for programming WR PLL clocks, used by HDMI and DVI outputs.
I split it into a separate patch to simplify the HDMI enabling patch which was
getting huge.

Note that this table is a temporary solution for WR PLL programming. It
will be reworked into a more exact algorithm at a later stage. But for
now, it provides the most accurate clock setting solution, so we use it
here.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Those are driven by DDIs on Haswell architecture, so we need to keep track
of which DDI is being used on each output.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Digital port detection on Haswell is indicated by the presence of a bit in
DDI_BUF_CTL for port A, and by a different register for ports B, C and D.
So we check for those bits during the initialization time and let the hdmi
function know about those.

Note that this bit does not indicates whether the output is DP or HDMI.
However, the DDI buffers can be programmed in a way that is shared between
DP/HDMI and FDI/HDMI except for PORT E.

So for now, we detect those digital outputs as being HDMI, but proper DP
support is still pending.

Note that DDI A can only drive eDP, so we do not handle it here for hdmi
initialization.

v2: simplify Haswell handling logic

v3: use generic function for handling digital outputs.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The iCLKIP clock is used to drive the VGA pixel clock on the PCH. In order
to do so, it must be programmed to properly do the clock ticks according
to the divisor, phase direction, phase increments and a special auxiliary
divisor for 20MHz clock.

v2: calculate divisor values directly instead of relying on a table.

v3: merged a fix from Ben to properly check for invalid divider values.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The line time can be programmed according to the number of horizontal
pixels vs effective pixel rate ratio.

v2: improve comment as per Chris Wilson suggestion

v3: incorporate latest changes in specs.

v4: move into wm update routine, also mention that the same routine can
program IPS watermarks. We do not have their enablement code yet, nor
handle the required clock settings at the moment, so this patch won't
program those values for now.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For now, we simple reuse the Ivy Bridge routines here.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Starting with Haswell, DDI ports can work in FDI mode to support
connectivity with the outputs located on the PCH.

This commit adds support for such connections in the intel_ddi module, and
provides Haswell-specific functionality to make it work.

v2: simplify the commit as per Daniel Vetter suggestion.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DDI is introduced starting with Haswell GPU generation. So to simplify its
management in the future, we also add intel_ddi.c to hold all the
DDI-related items.

Buffer translations for DDI links must be initialized prior to enablement.
For FDI and DP, first 9 pairs of values are used to select the connection
parameters. HDMI uses the last pair of values and ignores the first 9
pairs. So we program HDMI values in both cases, which allows HDMI to work
over both FDI and DP-friendly buffers.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Haswell, only one pipe can work in FDI mode, so this patch prevents
messing with wrong registers when FDI is being used by non-first pipe. And
to prevent this, we also specify that the VGA can only be used on pipe 0
for now in the crtc_mask value.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Prevent bogus asserts on DDI-related paths.

Longer explanation from Eugeni by mail:

"For the asserts there are 3 paths where we hit them:
- in assert_fdi_tx (we don't have the FDI_TX_CTL anymore, backup plan
  DDI_FUNC_CTL is used instead)
- in assert_fdi_tx_pll_enabled (we have the combination of iCLKIP and
  DDI_FUNC_CTL, plus PORT_CLK_SEL and PIPE_CLK_SEL now to make things
  work). We could use an assert here indeed - if we configure port to
  use one clock, and pipe to use another, everything hangs. Right now,
  we configure all of them in one place only; but yes, when DP code
  lands it will get more funky.
- and in ironlake_fdi_pll_enable. I reuse part of this function (to
  configure the TU sizes), but as in the 1st case, FDI_TX_CTL is gone
  so I just ignore it here."
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: Pasted Eugeni's explanation into the commit message.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Avoid bogus asserts and PCH PLL accesses on Lynx Point.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This attempts to enable all the available power wells during the
initialization.

Those power wells can be enabled in parallel or on-demand, and disabled
when no longer needed, but this is out of scope of this initial
enablement. Proper tracking of who uses which power well will require
a considerable rework of our display handling, so we just leave them all
enabled when the driver is loaded for now.

v2: use more generic and future-proof code
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Haswell, the recommended PCH-connected output is the one driven by DDI
E in FDI mode, used for VGA connection. All the others are handled by the
CPU.

Note that this does not accounts for Haswell/PPT combination yet, so if we
encounter such combination an error message is thrown to indicate that
things could go wrong.

v2: improve non-LPT detection warning per Daniel Vetter's suggestion.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This should be already configured when FDI auto-negotiation is done.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This will throw a BUG() message when an unknown sdvox register is
given to intel_hdmi_init. When this happens, things could going to be pretty
much broken afterwards, so we better detect this as soon as possible.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As suggested by Chris Wilson and Daniel Vetter, this chunk of code can be
simplified with a more simple check.

Also, as noticed by Jesse Barnes, it is worth mentioning that plane is an
enum and num_pipe is an int, so we could be more paranoid here about those
validation checks eventually.

CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This adds proper support for calculating those watermarks, checking for
number of available pipes instead of specific GPU variants when deciding
if watermarks for 3rd pipe are necessary.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With Lynx Point, we need to use SBI to communicate with the display clock
control. This commit adds helper functions to access the registers via
SBI.

v2: de-inline the function and address changes in bits names

v3: protect operations with dpio_lock, increase timeout to 100 for
paranoia sake.

v4: decrease paranoia a bit, as noticed by Chris Wilson
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Haswell interrupts are mostly similar with Ivy Bridge, so we share same
routines with it.

This patch also simplifies the vblank counter handling for all the Gen5+
architectures.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Haswell has different DIP control registers and offsets which we need to
use for infoframes, which this patch adds.

Note that this does not adds full DIP frames support, but only the basic
functionality necessary for HDMI to work in early enablement.

v2: replace infoframe handling with a debug message, proper support will
be added via a patch from Paulo Zanoni later.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we call gen6_enable_rps() (which writes into the per-ring
register mmio space) from intel_modeset_init_hw() which is called before
we initialise the rings. If we defer intel_modeset_init_hw() until
afterwards (in the intel_modeset_gem_init() phase) all is well.

v2: Rectify ordering of gem vs display HW init upon resume. (Daniel)

v3: Fix up locking. (Paulo)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Smash Paulo's locking fix onto Chris' patch.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We can take advantage that the PCH_IIR is a subordinate register to
reduce one of the required IIR reads, and that we only need to clear
interrupts handled to reduce the writes. And by simply tidying the code
we can reduce the line count and hopefully make it more readable.

v2: Split out the bugfix from the refactoring.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently the code re-reads PCH_IIR during the hotplug interrupt
processing. Not only is this a wasted read, but introduces a potential
for handling a spurious interrupt as we then may not clear all the
interrupts processed (since the re-read IIR may contains more interrupts
asserted than we clear using the result of the original read).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Inspired by the recent ppgtt regression report, where switching of
dmar only for the gpu seems to fix things completely, I've looked
again at the semaphores+vt-d situation.

Contrary to my earlier testing a few months back my system is now
stable with dmar disabled for the igd, and not only when disabling
dmar completely.

So I'm rather hopeful that all our recent fixes for snb have changed
things for code and it's time to try enabling semaphores again. We've
also had issues with enabling semaphores which are not vt-d related,
but I guess these are all fixed by the autoreport-disabling and lazy
request fix. And there's only one way to find out whether there are
still other issues ...

When I've tried to apply this patch I've noticed that semaphores on
gen6 have already silently been enabled in

commit 2911a35b
Author: Ben Widawsky <ben@bwidawsk.net>
Date:   Thu Apr 5 14:47:36 2012 -0700

    drm/i915: use semaphores for the display plane

Fix this up by only checking whether dmar is enabled on the gfx (not
on the entire system).
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... given that I essentially run the show already, let's make this
official.
Acked-by: NDave Airlie <airlied@redhat.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These two functions are actually hw-specific and only valid for gm45
thru gen7. HSW completely changes how this works, so label them
accordingly.

v2: s/gm45/g4x/ like for the previous patch.
Acked-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Generally we call stuff with i9xx_ when it's valid for gen3+. But
gen3 and early gen4 only support hdmi with sdvo cards, and writing
infoframes works completely different there.

v2: Use g4x instead of gm45 - it applies to the desktop variant, too.

v3: Properly align the paramters of g4x_write_infoframe again, noticed
by Paulo Zanoni.
Acked-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Simplifies things because for all the infoframes we care about,
we always send them on each vblank. Also, this gets rid of one
of the hw specific functions mislabelled with the intel_ prefix -
hsw will completely change how this works!
Acked-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The principle of intel_mark_busy() is that we want to spot the
transition of when the display engine is being used in order to bump
powersaving modes and increase display clocks. As such it is only
important when the display is changing, i.e. when rendering to the
scanout or other sprite/plane, and these are characterised by being
pinned.

v2: Mark the whole device as busy on execbuffer and pageflips as well
and rebase against dinq for the minor bug fix to be immediately
applicable.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: fix compile fail.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_wait_for_vblank uses PIPESTAT, which does not exist on Ironlake
and newer, so now we use PIPEFRAME.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Ditch the check for disable pipe from the new ilk wait for
vblank function to keep it consisten with existing behaviour.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just like Gen 4, IBX has a "Port Select" field on the DIP register,
but the ports are different.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

IBX does not need the workaround used in cpt_write_infoframe that
requires the AVI frame to be enabled while being updated.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>