state is unsigned long so the test did not work.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This message shows up for each cpu.  Print as debug messages.

[   12.893967] processor ACPI0007:00: registered as cooling_device0
[   12.907838] processor ACPI0007:01: registered as cooling_device1
Signed-off-by: NMike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: linux-acpi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NLen Brown <len.brown@intel.com>

acpi_check_resource_conflict() doesn't change the resource
it operates on, so the res parameter can be marked const.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

request_region should be used with release_region, not request_mem_region.

Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.

The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r1@
expression start;
@@

request_region(start,...)

@b1@
expression r1.start;
@@

request_mem_region(start,...)

@depends on !b1@
expression r1.start;
expression E;
@@

- release_mem_region
+ release_region
  (start,E)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

TXx9 SPI bit rate is calculated by:
        fBR = (spi-baseclk) / (n + 1)
Fix calculation of min_speed_hz, max_speed_hz and n.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

These laptops often leave i8042 in a wierd state resulting in non-
operational touchpad and keyboard.
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The version that made it into mainline missed the initialisation of the
chip handle.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

mmc_remove_host() will cause the mmc core to switch off the bus power by
eventually calling pxamci_set_ios(). This function uses the regulator or
the GPIO which have been freed already.

This causes the following Oops on module unload.

[   49.519649] Unable to handle kernel paging request at virtual address 30303a70
[   49.526878] pgd = c7084000
[   49.529563] [30303a70] *pgd=00000000
[   49.533136] Internal error: Oops: 5 [#1]
[   49.537025] last sysfs file: /sys/devices/platform/pxa27x-ohci/usb1/1-1/1-1:1.0/host0/target0:0:0/0:0:0:0/scsi_level
[   49.547471] Modules linked in: pxamci(-) eeti_ts
[   49.552061] CPU: 0    Not tainted  (2.6.32-rc8 #322)
[   49.557001] PC is at regulator_is_enabled+0x3c/0xbc
[   49.561846] LR is at regulator_is_enabled+0x30/0xbc
[   49.566691] pc : [<c01a2448>]    lr : [<c01a243c>]    psr: 60000013
[   49.566702] sp : c7083e70  ip : 30303a30  fp : 00000000
[   49.578093] r10: c705e200  r9 : c7082000  r8 : c705e2e0
[   49.583280] r7 : c7061340  r6 : c7061340  r5 : c7083e70  r4 : 00000000
[   49.589759] r3 : c04dc434  r2 : c04dc434  r1 : c03eecea  r0 : 00000047
[   49.596241] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
[   49.603329] Control: 0000397f  Table: a7084018  DAC: 00000015
[   49.609031] Process rmmod (pid: 1101, stack limit = 0xc7082278)
[   49.614908] Stack: (0xc7083e70 to 0xc7084000)
[   49.619238] 3e60:                                     c7082000 c703c4f8 c705ea00 c04f4074
[   49.627366] 3e80: 00000000 c705e3a0 ffffffff c0247ddc c70361a0 00000000 c705e3a0 ffffffff
[   49.635499] 3ea0: c705e200 bf006400 c78c4f00 c705e200 c705e3a0 ffffffff c705e200 ffffffff
[   49.643633] 3ec0: c04d8ac8 c02476d0 ffffffff c0247c60 c705e200 c0248678 c705e200 c0249064
[   49.651765] 3ee0: ffffffff bf006204 c04d8ad0 c04d8ad0 c04d8ac8 bf007490 00000880 c00440c4
[   49.659898] 3f00: 0000b748 c01c5708 bf007490 c01c44c8 c04d8ac8 c04d8afc bf007490 c01c4570
[   49.668031] 3f20: bf007490 bf00750c c04f4258 c01c37a4 00000000 bf00750c c7083f44 c007b014
[   49.676162] 3f40: 4000d000 6d617870 08006963 00000001 00000000 c7085000 00000001 00000000
[   49.684287] 3f60: 4000d000 c7083f8c 00000001 bea01a54 00005401 c7ab1400 c00440c4 00082000
[   49.692420] 3f80: bf00750c 00000880 c7083f8c 00000000 4000cfa8 00000000 00000880 bea01cc8
[   49.700552] 3fa0: 00000081 c0043f40 00000000 00000880 bea01cc8 00000880 00000006 00000000
[   49.708677] 3fc0: 00000000 00000880 bea01cc8 00000081 00000097 0000cca4 0000b748 00000000
[   49.716802] 3fe0: 4001a4f0 bea01cc0 00018bf4 4001a4fc 20000010 bea01cc8 a063e021 a063e421
[   49.724958] [<c01a2448>] (regulator_is_enabled+0x3c/0xbc) from [<c0247ddc>] (mmc_regulator_set_ocr+0x14/0xd8)
[   49.734836] [<c0247ddc>] (mmc_regulator_set_ocr+0x14/0xd8) from [<bf006400>] (pxamci_set_ios+0xd8/0x17c [pxamci])
[   49.745044] [<bf006400>] (pxamci_set_ios+0xd8/0x17c [pxamci]) from [<c02476d0>] (mmc_power_off+0x50/0x58)
[   49.754555] [<c02476d0>] (mmc_power_off+0x50/0x58) from [<c0247c60>] (mmc_detach_bus+0x68/0xc4)
[   49.763207] [<c0247c60>] (mmc_detach_bus+0x68/0xc4) from [<c0248678>] (mmc_stop_host+0xd4/0x1bc)
[   49.771944] [<c0248678>] (mmc_stop_host+0xd4/0x1bc) from [<c0249064>] (mmc_remove_host+0xc/0x20)
[   49.780681] [<c0249064>] (mmc_remove_host+0xc/0x20) from [<bf006204>] (pxamci_remove+0xc8/0x174 [pxamci])
[   49.790211] [<bf006204>] (pxamci_remove+0xc8/0x174 [pxamci]) from [<c01c5708>] (platform_drv_remove+0x1c/0x24)
[   49.800164] [<c01c5708>] (platform_drv_remove+0x1c/0x24) from [<c01c44c8>] (__device_release_driver+0x7c/0xc4)
[   49.810110] [<c01c44c8>] (__device_release_driver+0x7c/0xc4) from [<c01c4570>] (driver_detach+0x60/0x8c)
[   49.819535] [<c01c4570>] (driver_detach+0x60/0x8c) from [<c01c37a4>] (bus_remove_driver+0x90/0xcc)
[   49.828452] [<c01c37a4>] (bus_remove_driver+0x90/0xcc) from [<c007b014>] (sys_delete_module+0x1d8/0x254)
[   49.837891] [<c007b014>] (sys_delete_module+0x1d8/0x254) from [<c0043f40>] (ret_fast_syscall+0x0/0x28)
[   49.847145] Code: eb06c53a e596c030 e1a0500d e59f106c (e59c0040)
[   49.853566] ---[ end trace b5fa66a00cea142f ]---
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Reported-by: NSven Neumann <s.neumann@raumfeld.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@kernel.org
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch fixes the compilation failure of
rc32434 due to a bad module parameter description.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The size value passed to ioremap_nocache() is not correct.
Use resource_size() to get the correct value.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

When detecting power failure, the probe function would reset the clock
time to defined state.

However, the clock's _date_ might still be bogus and a subsequent probe
fails when sanity-checking these values.

Change the power-failure fixup code to do a full setting of rtc_time,
including a valid date.
Signed-off-by: NJohannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The possible CCR_Y2K register values are 19 or 20 and struct rtc_time's
tm_year is in years since 1900.

The function translating rtc_time to register values assumes tm_year to be
years since first christmas, though, and we end up storing 0 or 1 in the
CCR_Y2K register, which the hardware does not refuse to do.

A subsequent probing of the clock fails due to the invalid value range in
the register, though.

[ And if it didn't, reading the clock would yield a bogus year because
  the function translating registers to tm_year is assuming a register
  value of 19 or 20. ]

This fixes the conversion from years since 1900 in tm_year to the
corresponding CCR_Y2K value of 19 or 20.
Signed-off-by: NJohannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Prevent the AoE block driver from creating cache aliases of page cache
pages on machines with virtually indexed caches.

Building kernels on an AT91SAM9G20 board without this patch fails with
segmentation faults after a couple of passes.
Signed-off-by: NPeter Horton <zero@colonel-panic.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Remove wrong and unnecessary unmask operation

- Remove extra GEDR reading

This fixes the loss of interrupts which occurs when two or more pins are
triggered in close succession.
Signed-off-by: NAlek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Following issues have been addressed on DA8XX/OMAP-L1XX:

a. Screen misalignment during booting when frame buffer console is
   enabled.

b. Driver was configured always in PSEUDOCOLOR mode.  This patch
   dynamically configures the driver either in PSEUDOCOLOUR or TRUECOLOR
   mode depending on bpp.

c. The RED and BLUE offsets were interchanged resulting in wrong
   bootup logo colour.

This patch has been tested on DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"rtc" is freed and then dereferenced on the next line.  This patch fixes
that.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes:

  v4l/dvb_frontend.c: In function 'dvb_frontend_stop':
  v4l/dvb_frontend.c:707: error: implicit declaration of function 'init_MUTEX'

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14609

Reported-by: <tstrelar@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There was confusion between the array size and the highest ISEL
value possible.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

commit 4706b349 was a forward port of a fix that was needed
for SLES10.  But in fact it is not needed in mainline because
the earlier commit dd00a99e fixes the same problem in a
better way.
Further, this commit introduces a bug in the way it interacts with
the automatic read-error-correction.  If, after a read error is
successfully corrected, the same disk is chosen to re-read - the
re-read won't be attempted but an error will be returned instead.

After reverting that commit, there is the possibility that a
read error on a read-only array (where read errors cannot
be corrected as that requires a write) will repeatedly read the same
device and continue to get an error.
So in the "Array is readonly" case, fail the drive immediately on
a read error.
Signed-off-by: NNeilBrown <neilb@suse.de>
Cc: stable@kernel.org

This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf
stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...).

To see these ids, you need to switch the stick to modem operation first
with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to
1c9e:9603 and thus be recognized by the option driver.
Signed-off-by: NGernot Hillier <gernot@hillier.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().

By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Signed-off-by: NDaniel Glöckner <dg@emlix.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.

This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Signed-off-by: NDaniel Glöckner <dg@emlix.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Isochronous Tx DMA is getting programmed but never getting started
for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work.

Fixing it by starting DMAs using musb_h_tx_dma_start().
Signed-off-by: NSwaminathan S <swami.iyer@ti.com>
Signed-off-by: NBabu Ravi <ravibabu@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Removes below unnecessary log of almost 28 lines during boot.

musb_hdrc: hw_ep 0shared, max 64
musb_hdrc: hw_ep 1tx, max 512
musb_hdrc: hw_ep 1rx, max 512
...
...
musb_hdrc: hw_ep 13shared, max 4096
musb_hdrc: hw_ep 14shared, max 1024
musb_hdrc: hw_ep 15shared, max 1024
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- fixed shared interrupt bug reported by Vadim Lobanov
 - fixed possible warning oops on driver unload when connected
 - prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
   when using gadget ether
Signed-off-by: NThomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: Robert Richter <robert.richter@amd.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write.  On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.

If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.

Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate().  And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...

While at it, also do the following changes :

- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
  driver does not allow stalling with non-empty Tx FIFO anyway);

- in rxstate(), stop pointlessly zeroing the 'csr' variable;

- in musb_gadget_set_halt(), move the 'done' label to a more proper
  place;

- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1304) fixes a regression in ehci-hcd.  Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.

The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake.  In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found.  In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.

Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests.  Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJavier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove my mail address.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix some missing author names.
They were accidentally removed by someone within Microsoft before the
files were sent for inclusion in the kernel.
Signed-off-by: NHank Janssen <hjanssen@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The flag ENABLE_POLLING is always enabled in original Makefile, but
accidently removed during porting to mainline kernel. The patch fixes
this bug which can cause stalled network communication.  Credit needs to
go to Eric Sesterhenn <eric.sesterhenn@lsexperts.de> For pointing out a
typo in the original code as well.
Signed-off-by: NHank Janssen <hjanssen@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Nearly every invocation of memset in drivers/staging/hv/StorVsc.c has
its arguments the wrong way around.
Signed-off-by: NDave Jones <davej@redhat.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
Reported-by: NAlon Ziv <alonz@nolaviz.org>
Signed-off-by: NMichal Simek <monstr@monstr.eu>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver missed a small API change while sitting in Ralf's tree, this
patch makes it compile again.
Signed-off-by: NMaxime Bizon <mbizon@freebox.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some drivers allow O_NDELAY of a dead port (eg for setserial to work). In that
situation we must not try to raise the carrier.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix mutex function usage, which was overlooked in a previous patch.
Signed-off-by: NPete Eberlein <pete@sensoray.com>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As pointed by Stefan Lippers-Hollmann <s.L-H@gmx.de>,

Commit:	fd9a40da broke s2250
compilation.

This patch re-adds the missing s2250-loader.h
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Lennert Buytenhek noticed that delBA handling in mac80211
was broken and has remotely triggerable problems, some of
which are due to some code shuffling I did that ended up
changing the order in which things were done -- this was

  commit d75636ef
  Author: Johannes Berg <johannes@sipsolutions.net>
  Date:   Tue Feb 10 21:25:53 2009 +0100

    mac80211: RX aggregation: clean up stop session

and other parts were already present in the original

  commit d92684e6
  Author: Ron Rindjunsky <ron.rindjunsky@intel.com>
  Date:   Mon Jan 28 14:07:22 2008 +0200

      mac80211: A-MPDU Tx add delBA from recipient support

The first problem is that I moved a BUG_ON before various
checks -- thereby making it possible to hit. As the comment
indicates, the BUG_ON can be removed since the ampdu_action
callback must already exist when the state is != IDLE.

The second problem isn't easily exploitable but there's a
race condition due to unconditionally setting the state to
OPERATIONAL when a delBA frame is received, even when no
aggregation session was ever initiated. All the drivers
accept stopping the session even then, but that opens a
race window where crashes could happen before the driver
accepts it. Right now, a WARN_ON may happen with non-HT
drivers, while the race opens only for HT drivers.

For this case, there are two things necessary to fix it:
 1) don't process spurious delBA frames, and be more careful
    about the session state; don't drop the lock

 2) HT drivers need to be prepared to handle a session stop
    even before the session was really started -- this is
    true for all drivers (that support aggregation) but
    iwlwifi which can be fixed easily. The other HT drivers
    (ath9k and ar9170) are behaving properly already.
Reported-by: NLennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes kernel bugzilla #14691

Due to the way netpoll works, it is perfectly legal to see
NAPI already scheduled when new device events are pending
in b44_interrupt().

So logging a message about it is wrong and in fact harmful.

Based upon a patch by Andreas Mohr.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>