Not respecting udelay causes problems with any virtual hardware that is passed
through to real hardware.  This can be noticed by any device that interacts
with the real world in real time - like AP startup, which takes real time.  Or
keyboard LEDs, which should blink in real-time.  Or floppy drives, but only
when passed through to a real floppy controller on OSes which can't
sufficiently buffer the floppy commands to emulate a zero latency floppy.  Or
IDE drives, when connecting to a physical CDROM.

This was mostly a hack to get the kernel to boot faster, but it introduced a
number of misvirtualization bugs, and Alan and Pavel argued pretty strongly
against it.  We were the only client, and now want to clean up this cruft.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide a PT map hook for HIGHPTE kernels to designate where they are mapping
page tables.  This information is required so the physical address of PTE
updates can be determined; otherwise, the mm layer would have to carry the
physical address all the way to each PTE modification callsite, which is even
more hideous that the macros required to provide the proper hooks.

So lets not mess up arch neutral code to achieve this, but keep the horror in
an #ifdef HIGHPTE in include/asm-i386/pgtable.h.  I had to use macros here
because some types are not yet defined in all the include paths for this
header.

This patch is absolutely required for HIGHPTE kernels to operate properly with
VMI.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In order to share the common code in tsc.c which does CPU Khz calibration, we
need to make an accurate value of CPU speed available to the tsc.c code.  This
value loses a lot of precision in a VM because of the timing differences with
real hardware, but we need it to be as precise as possible so the guest can
make accurate time calculations with the cycle counters.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The custom_sched_clock hook is broken.  The result from sched_clock needs to
be in nanoseconds, not in CPU cycles.  The TSC is insufficient for this
purpose, because TSC is poorly defined in a virtual environment, and mostly
represents real world time instead of scheduled process time (which can be
interrupted without notice when a virtual machine is descheduled).

To make the scheduler consistent, we must expose a different nature of time,
that is scheduled time.  So deprecate this custom_sched_clock hack and turn it
into a paravirt-op, as it should have been all along.  This allows the tsc.c
code which converts cycles to nanoseconds to be shared by all paravirt-ops
backends.

It is unfortunate to add a new paravirt-op, but this is a very distinct
abstraction which is clearly different for all virtual machine
implementations, and it gets rid of an ugly indirect function which I
ashamedly admit I hacked in to try to get this to work earlier, and then even
got in the wrong units.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Critical bugfixes for the VMI-Timer code.

1) Do not setup a one shot alarm if we are keeping the periodic alarm
   armed.  Additionally, since the periodic alarm can be run at a lower rate
   than HZ, let's fixup the guard to the no-idle-hz mode appropriately.  This
   fixes the bug where the no-idle-hz mode might have a higher interrupt rate
   than the non-idle case.

2) The interrupt handler can no longer adjust xtime due to nested lock
   acquisition.  Drop this.  We don't need to check for wallclock time at
   every tick, it can be done in userspace instead.

3) Add a bypass to disable noidle operation.  This is useful as a last
   minute workaround, or testing measure.

4) The code to skip the IO_APIC timer testing (no_timer_check) should be
   conditional on IO_APIC, not SMP, since UP kernels can have this configured
   in as well.
Signed-off-by: NDan Hecht <dhecht@vmware.com>
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

VMI timer code.  It works by taking over the local APIC clock when APIC is
configured, which requires a couple hooks into the APIC code.  The backend
timer code could be commonized into the timer infrastructure, but there are
some pieces missing (stolen time, in particular), and the exact semantics of
when to do accounting for NO_IDLE need to be shared between different
hypervisors as well.  So for now, VMI timer is a separate module.

[Adrian Bunk: cleanups]

Subject: VMI timer patches
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

Fairly straightforward implementation of VMI backend for paravirt-ops.

[Adrian Bunk: some cleanups]
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>