overloaded gfp_t param.

SGI-PV: 954580
SGI-Modid: xfs-linux-melb:xfs-kern:26552a
Signed-off-by: NNathan Scott <nathans@sgi.com>
Signed-off-by: NTim Shimmin <tes@sgi.com>

SGI-PV: 954580
SGI-Modid: xfs-linux-melb:xfs-kern:26551a
Signed-off-by: NNathan Scott <nathans@sgi.com>
Signed-off-by: NTim Shimmin <tes@sgi.com>

Avoids doing an unnecessary inode to vnode conversion and avoids a memory
allocation.

SGI-PV: 904196
SGI-Modid: xfs-linux-melb:xfs-kern:26492a
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NNathan Scott <nathans@sgi.com>
Signed-off-by: NTim Shimmin <tes@sgi.com>

SGI-PV: 954365
SGI-Modid: xfs-linux-melb:xfs-kern:26406a
Signed-off-by: NTim Shimmin <tes@sgi.com>

analysis.

Under a sequential create+allocate workload, blktrace reported backward
writes being issued by xfsbufd, and frequent inappropriate queue unplugs.
We now insert at the tail when moving from the delwri lists to the temp
lists, which maintains correct ordering, and we avoid unplugging queues
deep in the submit paths when we'd shortly do it at a higher level anyway.
blktrace now reports much healthier write patterns from xfsbufd for this
workload (and likely many others).

SGI-PV: 954310
SGI-Modid: xfs-linux-melb:xfs-kern:26396a
Signed-off-by: NNathan Scott <nathans@sgi.com>
Signed-off-by: NTim Shimmin <tes@sgi.com>

"inode => vnode => inode" conversion, but only flags and mode of final
inode are looked at. Pass original inode instead.

SGI-PV: 904196
SGI-Modid: xfs-linux-melb:xfs-kern:26395a
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NNathan Scott <nathans@sgi.com>
Signed-off-by: NTim Shimmin <tes@sgi.com>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
  [PATCH] bonding: update version number
  [PATCH] git-netdev-all: pc300_tty build fix
  [PATCH] Make PC300 WAN driver compile again
  [PATCH] Modularize generic HDLC
  [PATCH] more s2io __iomem annotations
  [PATCH] restore __iomem annotations in e1000
  [PATCH] 64bit bugs in s2io
  [PATCH] bonding: Fix primary selection error at enslavement time
  [PATCH] bonding: Don't mangle LACPDUs
  [PATCH] bonding: Validate probe replies in ARP monitor
  [PATCH] bonding: Don't release slaves when master is admin down
  [PATCH] bonding: Add priv_flag to avoid event mishandling
  [PATCH] bonding: Handle large hard_header_len
  [PATCH] bonding: Remove unneeded NULL test
  [PATCH] bonding: Format fix in seq_printf call
  [PATCH] bonding: Convert delay value from s16 to int
  [PATCH] bonding: Allow bonding to enslave a 10 Gig adapter
  Delete unused drivers/net/gt64240eth.h
  [PATCH] skge: fiber support
  [PATCH] fix possible NULL ptr deref in forcedeth
  ...

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] Don't use old-EH ->eng_timeout() hook when not needed
  [libata] sata_mv: fix oops by filling in missing hook
  [libata] One more s/15/ATA_SECONDARY_IRQ/ substitution
  [libata] pata_serverworks: fill in ->irq_clear hook
  [PATCH] pata_serverworks: correct PCI ID in cable detection table
  [PATCH] libata-sff: use our IRQ defines
  [PATCH] libata-eh: Remove layering violation and duplication when handling absent ports
  [PATCH] libata: tighten rules for legacy dependancies
  [PATCH] libata: refuse to register IRQless ports

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (129 commits)
  [PATCH] USB Storage: fix Rio Karma eject support build error
  USB: Airprime driver improvements to allow full speed EvDO transfers
  USB: remove OTG build warning
  USB: EHCI update VIA workaround
  USB: force root hub resume after power loss
  USB: ohci_usb can oops on shutdown
  USB: Dealias -110 code (more complete)
  USB: Remove unneeded void * casts in core files
  USB: u132-hcd: host controller driver for ELAN U132 adapter
  USB: ftdi-elan: client driver for ELAN Uxxx adapters
  usb serial: support Alcor Micro Corp. USB 2.0 TO RS-232 through pl2303 driver
  USB: Moschip 7840 USB-Serial Driver
  USB: add PlayStation 2 Trance Vibrator driver
  USB: Add ADU support for Ontrak ADU devices
  aircable: fix printk format warnings
  Add AIRcable USB Bluetooth Dongle Driver
  cypress_m8: implement graceful failure handling
  cypress_m8: improve control endpoint error handling
  cypress_m8: use usb_fill_int_urb where appropriate
  cypress_m8: use appropriate URB polling interval
  ...

The new code does clobber the result early, so make sure to tell
gcc to not put it into the same register as a input argument
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: NKyle McMartin <kyle@parisc-linux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

	I neglected to properly update the version number in the recent
patch series; this sets it to something reasonable.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In file included from drivers/net/wan/pc300_tty.c:59:
drivers/net/wan/pc300.h:335: error: field 'pppdev' has incomplete type

Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In file included from drivers/usb/storage/usb.c:180:
drivers/usb/storage/unusual_devs.h:221: error: 'US_PR_KARMA' undeclared here (not in a function)
drivers/usb/storage/unusual_devs.h:221: error: 'rio_karma_init' undeclared here (not in a function)

Cc: Keith Bennett <keith@mcs.st-and.ac.uk>
Acked-by: NBob Copeland <me@bobcopeland.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adapted from an earlier patch by Greg KH <gregkh@suse.de>.
That patch added multiple read urbs and larger transfer buffers to allow
data transfers at full EvDO speed.

This version includes additional device IDs and fixes a memory leak in
the transfer buffer allocation.

Some (maybe all?) of the supported devices present multiple bulk endpoints,
the additional EPs can be used for control and status functions,
This version allocates 3 EPs by default, that can be changed using
the 'endpoints' module parameter.

Tested with Sierra Wireless EM5625 and MC5720 embedded modules.

Device ID (0x0c88, 0x17da) for the Kyocera Wireless KPC650/Passport
was added but is not yet tested.


From: Andy Gay <andy@andynet.net>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Somewhere along the line, a variable in a USB-OTG codepath
stopped being used; this removes the relevant compiler warning.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This revamps handling of the hardware "async advance" IRQ, and its watchdog
timer.  Basically it dis-entangles that important timeout from the others,
simplifying the associated state and code to make it more robust.

This reportedly improves behavior of EHCI on some systems with VIA chips,
and AFAIK won't affect non-VIA hardware.  VIA systems need this code to
recover from silcon bugs whereby the "async advance" IRQ isn't issued.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch(as785) forces the PM core to resume a root hub after a
power loss during system sleep.  If the root hub had been suspended
before the system sleep then normally the PM core would not resume it
afterward.  Without this resume, various sorts of wakeup events (like
port change events) can get lost.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When ohci-hcd is shutting down (for rmmod or PC-card removal), there is
a window when the device is shut down, HC communication area (->hcca)
is freed, but the core has not called "free_irq" yet. If another device
triggers a shared interrupt in this window, we oops when trying to
access the freed ->hcca.

This patch removes the window by calling free_irq before ->hcca is freed.

The patch is tested at the PC hotplug test rig at Stratus, and with
rmmod by Rafael Wysocki.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".

The usbmon splits such cases already thanks to its timestamp, but
it's not always available.

I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch removes unneeded casts for the following (void *) pointers:
 - struct file: private
 - struct urb: context
 - struct usb_bus: hcpriv
 - return value of kmalloc()

The patch also contains some whitespace cleanup in the relevant areas.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This "u132-hcd" module is one half of the "driver" for
ELAN's U132 which is a USB to CardBus OHCI controller
adapter. This module needs the "ftdi-elan" module in
order to communicate to CardBus OHCI controller inserted
into the U132 adapter.

When the "ftdi-elan" module detects a supported CardBus
OHCI controller in the U132 adapter it loads this "u132-hcd"
module.

Upon a successful device probe() the single workqueue
is started up which does all the processing of commands
from the USB core that implement the host controller.

The workqueue maintains the urb queues and issues commands
via the functions exported by the "ftdi-elan" module. Each
such command will result in a callback.

Note that the "ftdi-elan" module is a USB client driver.

Note that this "u132-hcd" module is a (cut-down OHCI)
host controller.

Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.
Signed-off-by: NTony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This "ftdi-elan" module is one half of the "driver" for
ELAN's Uxxx series adapters which are USB to PCMCIA CardBus
adapters. Currently only the U132 adapter is available and
it's module is called "u132-hcd".

When the USB hot plug subsystem detects a Uxxx series adapter
it should load this module.

Upon a successful device probe() the jtag device file interface
is created and the status workqueue started up.

The jtag device file interface exists for the purpose of
updating the firmware in the Uxxx series adapter, but as
yet it had never been used.

The status workqueue initializes the Uxxx and then sits there
polling the Uxxx until a supported PCMCIA CardBus device is
detected it will start the command and respond workqueues
and then load the module that handles the device. This will
initially be only the u132-hcd module. The status workqueue
then just polls the Uxxx looking for card ejects.

The command and respond workqueues implement a command
sequencer for communicating with the firmware on the other
side of the FTDI chip in the Uxxx. This "ftdi-elan" module
exports some functions to interface with the sequencer.

Note that this module is a USB client driver.

Note that the "u132-hcd" module is a (cut-down OHCI)
host controller.

Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.
Signed-off-by: NTony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Patch to add support for Alcor Micro Corp. USB 2.0 TO RS-232 converter.
This patch adds VID and PID to pl2303.[ch], adds it to the "HORRIBLE
HACK FOR PL2303" in usb-serial.c and also prevents cdc-acm to claim
driving this device by blacklisting it in hid-core.
Signed-off-by: NJohannes Steingraeber <Jo_Stein@web.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPaul B Schroeder <pschroeder@uplogix.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is a driver for the PlayStation 2 specific Trance Vibrator
device. The only thing that device can do is vibrate at various speeds.
Signed-off-by: NSam Hocevar <sam@zoy.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Luiz Fernando N. Capitulino" <lcapitulino@mandriva.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for Ontrak ADU USB devices.

Fixed for printk issues by Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NSteven Haigh <netwiz@crc.id.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix printk format warnings:
drivers/usb/serial/aircable.c:221: warning: format ‘%Zd’ expects type ‘signed size_t’, but argument 4 has type ‘int’
drivers/usb/serial/aircable.c:283: warning: format ‘%Zd’ expects type ‘signed size_t’, but argument 4 has type ‘int’
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add driver for AIRcable USB Bluetooth dongle.
Signed-off-by: NNaranjo, Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When receiving a fatal error from the USB core, e.g. EILSEQ (which can
happen if the polling interval is too short), fail gracefully.
Previously the driver would fill the log with useless error messages
or (more alarmingly) silently spin forever trying to write updated
control information to the device.  This change implements a new flag
which if cleared indicates that the driver has failed.  The flag will
be set on initialization, cleared on fatal errors, and anything else
that touches the USB port in the driver will abort if the flag is
clear.  When the flag is cleared, a message will be logged indicating
that the driver has failed.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix usb core function error return checks to look for negative errno
values, not positive errno values.  This bug had rendered those checks
useless.  Also remove attempted error recovery on control endpoints
for EPIPE - with control endpoints EPIPE does not indicate a halted
endpoint so trying to recover with usb_clear_halt() is not the correct
action.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Rather than directly filling in URB fields, it's safer to use
usb_fill_int_urb().  This improves robustness of the driver; URB
changes in the future will not go uninitialized here.  That point not
withstanding, this driver should at least be self-consistent.  Either
use usb_fill_int_urb() everywhere or don't bother with it all.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The polling interval for the device can't always be 1msec.  If it is
too quick, the device can fail causing a fatal (to the driver) EILSEQ
error from the USB core.  The actual correct value is reported by the
device as part of its configuration data, so use that value as the
default.  On a DeLorme Earthmate for example, the device reports that
it wants a 6msec interval.  As part of this fix, the "interval" module
option has been fixed as well; the device's default can be overridden
by specifying interval=<value> as a module option.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as786) removes a redundant test and fixes a problem
involving repeated system sleeps when CONFIG_USB_SUSPEND is not set.
During the first wakeup, the root hub's dev.power.power_state.event
field doesn't get updated, causing it not to be suspended during the
second sleep transition.

This takes care of the issue raised by Rafael J. Wysocki and Mattia
Dongili.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>