Gen1 chips use a 16 bit mailbox extension register, for upto 48 bit
mailbox commands. The newer generation chips use a 32 bit mailbox
extension register instead, for upto 64 bit mailbox commands.

Handle writing the larger mailboxes.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The different RF module seems to require a different AGC table as well
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer chips seem to have some different mac registers, requiring
a different init table.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

So far this is just for 8723BU. It includes writing to a number of
registers I have seen no description for so far.

0x0064
0x0930
0x0944
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add 8723bu 1T radio init table. The vendor driver indicates that some
registers need special treatment for TFBGA90, TFBGA80, and TFBGA79
packaging. However the vendor driver never actually checks the package
type, so just stick to default values here.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This adds the 8723bu PHY 1T init table.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Only 1st generation chips do provide USB interrupts, so do not try to
setup interrupts for newer chips (8192eu and 8723bu).
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8723bu, like the 8192eu, can also handle 1024 byte block writes.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement first stab at parsing the 8723bu's efuse.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This provides initial detection of 8723bu devices, and selects the
correct firmware image to load.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The newer generation chips have different interrupt registers.
Initialize this correct registers on 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu (and some other parts) will report an incorrect USB OUT
EP. This tells the chip to drop it - as per the vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The logic for testing auto load failure in rtl8xxxu_auto_llt_table()
was inverted.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To match the flow of the vendor driver, move the LLT init to after the
firmware is started.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This reorganizes the device initialization to init page boundaries
before starting the firmware. This matches the flow in the 8192eu
vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer chips can auto load the LLT table, it is no longer necessary to
build it manually in the driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This implements the rtl8192eu power on sequence, and splits it off
from the rtl8192cu/rtl8723au power on sequence.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The rtl8192eu can handle 1024 byte block writes, unlike it's
predecessors (8192cu/8188cu).
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This identifies the chip vendors correctly and also picks the correct
firmware for rtl8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is the start of 8192eu support. For now just detect the device
and parse the efuse.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add debugfs key (under CFG80211_CERTIFICATION_ONUS
configuration) to set/clear radar_debug_mode.
In this mode, the driver simply ignores radar
events (but prints them).

The fw is notified about this mode through
a special generic_cfg_feature command.

This mode is relevant only for ap mode. look for
it when initializing ap vif.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When working with AP + P2P, it's possible to get into
a state when the AP is in ROC (due to assiciating station)
while trying to ROC on the P2P interface.

Replace the WARN_ON with wl1271_error to avoid warnings
in this case.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In cfg80211 suspend handler, stop the netif queue and
wait until all the Tx queues become empty. Start the
queues in resume handler.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We met a problem of pm_suspend  when repeated closing/opening the lid
on a Lenovo laptop (1/20 reproduce rate), below is the log:

[ 199.735876] PM: Entering mem sleep
[ 199.750516] e1000e: EEE TX LPI TIMER: 00000011
[ 199.856638] Trying to free nonexistent resource <000000000000d000-000000000000d0ff>
[ 201.753566] brcmfmac: brcmf_pcie_suspend: Timeout on response for entering D3 substate
[ 201.753581] pci_legacy_suspend(): brcmf_pcie_suspend+0x0/0x1f0 [brcmfmac] returns -5
[ 201.753585] dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -5
[ 201.753589] PM: Device 0000:04:00.0 failed to suspend async: error -5

Through debugging, we found when problem happens, it is not the device
fails to enter D3, but the signal D3_ACK comes too early to pass the
waitqueue_active() check.

Just like this:
brcmf_pcie_send_mb_data(devinfo, BRCMF_H2D_HOST_D3_INFORM);
// signal is triggered here
wait_event_timeout(devinfo->mbdata_resp_wait, devinfo->mbdata_completed,
		   BRCMF_PCIE_MBDATA_TIMEOUT);

So far I think it is safe to remove waitqueue_active check since there
is only one place to trigger this signal (sending
BRCMF_H2D_HOST_D3_INFORM). And it is not a problem calling wake_up
event earlier than calling wait_event.

Cc: Brett Rudley <brudley@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We accidentally return success instead of a negative error code.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2016-03-09_2' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

* update GSCAN capabilities (Ayala)
* fix AES-CMAC in AP mode (Johannes)
* adapt prints to new firmware API
* rx path improvements (Sara and Gregory)
* fixes for the thermal / cooling device code (Chaya Rachel)
* fixes for GO uAPSD handling
* more code for the 9000 device family (Sara)
* infrastructure work for firmware notification (Chaya Rachel)
* improve association reliablity (Sara)
* runtime PM fixes
* fixes for ROC (HS2.0)

Gscan capabilities were updated with new capabilities supported
by the device. While at it, simplify the firmware support
conditional and move both conditions into the WARN() to make it
easier to undertand and use the unlikely() for both.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware/hardware only supports checking AES-CMAC on RX, not
using it on TX. For station mode this is fine, since it's the only
thing it will ever do. For AP mode, it never receives such frames,
but must be able to transmit them. This is currently broken since
we try to enable them for hardware crypto (for RX only) and then
treat them as TX_CMD_SEC_EXT, leading to FIFO underruns during TX
so the frames never go out to the air.

To fix this, simply use software on TX in AP (and IBSS) mode.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Newer firmware versions put different data in the memory
which is read by the driver upon firmware crash. Just
change the variable names in the code and the name of the
data in the log that we print withouth any functional
change.
On older firmware, there will be a mismatch between the
names that are printed and the content itself, but that's
harmless.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When trying to reach high Rx throughput of more than 500Mbps on
a device with a relatively weak CPU (Atom x5-Z8500), CPU utilization
may become a bottleneck. Analysis showed that we are looping in
iwl_pcie_rx_handle for very long periods which led to starvation
of other threads (iwl_pcie_rx_handle runs with _bh disabled).
We were handling Rx and allocating new buffers and the new buffers
were ready quickly enough to be available before we had finished
handling all the buffers available in the hardware. As a
consequence, we called iwl_pcie_rxq_restock to refill the hardware
with the new buffers, and start again handling new buffers without
exiting the function. Since we read the hardware pointer again when
we goto restart, new buffers were handled immediately instead of
exiting the function.

This patch avoids refilling RBs inside rx handling loop, unless an
emergency situation is reached. It also doesn't read the hardware
pointer again unless we are in an emergency (unlikely) case.
This significantly reduce the maximal time we spend in
iwl_pcie_rx_handle with _bh disabled.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_mvm_tcool_get_cur_state is the function that returns the
cooling state index to the sysfs handler. This function returns
mvm->cooling_dev.cur_state but that variable was set to the
budget and not the cooling state index. Fix that.
Add a missing blank line while at it.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

mac80211 advertises this feature for all its drivers.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We need to track the next packet that we will reclaim in
order to know when the Tx queues are empty. This is useful
when we open or tear down an A-MPDU session which requires
to switch queue.
The next packet being reclaimed is identified by its WiFi
sequence number and this is relevant only when we use QoS.
QoS NDPs do have a TID but have a meaningless sequence
number. The spec mandates the receiver to ignore the
sequence number in this case, allowing the transmitter to
put any sequence number. Our implementation leaves it 0.
When we reclaim a QoS NDP, we can't update the next_relcaim
counter since the sequence number of the QoS NDP itself is
invalid.
We used to update the next_reclaim based on the sequence
number of the QoS NDP which reset it to 1 (0 + 1) and
because of this, we never knew when the queue got empty.
This had to sad consequence to stuck the A-MPDU state
machine in a transient state.
To fix this, don't update next_reclaim when we reclaim
a QoS NDP.

Alesya saw this bug when testing u-APSD. Because the
A-MPDU state machine was stuck in EMPTYING_DELBA, we
updated mac80211 that we still have frames for that
station when it got back to sleep. mac80211 then wrongly
set the TIM bit in the beacon and requested to release
non-existent frames from the A-MPDU queue. This led to
a situation where the client was trying to poll frames
but we had no frames to send.
Reported-by: NAlesya Shapira <alesya.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

From 9000 family on, we need to get HW address from host
CSR registers.
OEM can override it by fusing the override registers - read
those first, and if those are 0 - read the OTP registers instead.

In addition - bail out if no valid mac address is present. Make
it shared for all NICs.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We kick the allocator when we have 2 RBDs that don't have
attached RBs, and the allocator allocates 8 RBs meaning
that it needs another 6 RBDs to attach the RBs to.
The design is that allocator should always have enough RBDs
to fulfill requests, so we give in advance 6 RBDs to the
allocator so that when it is kicked, it gets additional 2 RBDs
and has enough RBDs.
These RBDs were taken from the Rx queue itself, meaning
that each Rx queue didn't have the maximal number of
RBDs, but MAX - 6.
Change initial number of RBDs in the system to include both
queue size and allocator reserves.
Note the multi-queue is always 511 instead of 512 to avoid a
full queue since we cannot detect this state easily enough in
the 9000 arch.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When running async rx handler the framework holds the mvm->mutex
before starting the async handler, that might cause a deadlock in case
the handler calls to ops that lock the mutex as well.
Add support for running async rx handler without hold the mutex before
activating the handler.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently when the FW sends start/stop aux roc time event
notification with an error status, the driver returns an
error value, but does not remove the time event, and does
not notify the stack above that the time event is over.

This causes problems that the stack above assumes we are still
in the middle of a time event, and therefore can block different
events, such as scanning.

On FW failure notification, cleanup the time event parameters and
notify the stack above that the time event is over.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Our hardware de-aggregates AMSDUs but copies the mac header
as it to the de-aggregated MPDUs. We need to turn off the AMSDU
bit in the QoS control ourselves.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add debugfs entries to get the ctdp budget average
and to stop ctdp.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>