- 07 1月, 2011 26 次提交
-
-
由 Alex Deucher 提交于
The vbios only partially initializes the memory controller on NI, so now we need to load the MC ucode in the driver and set the default clocks once the ucode is loaded. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
The MC ucode is no longer loaded by the vbios tables as on previous asics. It now must be loaded by the driver. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
The hardware supports advanced user defined color management but at the moment, there is no infrastructure in place to take advantage of it so for now we just support the legacy LUTs. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
This adds some new NI (northern islands) specific display register defines. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
NI chips no longer load the MC ucode in the asic_init sequence so the asic comes up in a basic mode with low engine/memory clocks and a voltage. Once the MC ucode is loaded by the driver the card can be programmed to it's proper default clocks and voltage. As such the default clocks in the firmware info table as the post clocks, not the default running clocks. Track the default post clocks and default running clocks separately to handle this. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Same as Cypress. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Some systems disable the vbios on secondary cards or cards that have been posted. This code re-enabled the vbios so the driver can load it. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Needed to tell which DIG encoders are HBR2 capable for DP 1.2. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
The DVOOutputControl table was removed for DCE5. DVOEncoderControl now handles everything. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
The DAC1OutputControl table was removed for DCE5. DAC1EncoderControl now handles everything. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
only fusion asics are dce4.1 Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Supported on rv6xx/r7xx/evergreen. Cards come up in gen1 mode. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
- 06 1月, 2011 5 次提交
-
-
由 Alex Deucher 提交于
Reported-by: N屋国遥 <hyagni@gmail.com> Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Cc: stable@kernel.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Tejun Heo 提交于
With cmwq, there's no reason for radeon to use a dedicated workqueue. Drop dev_priv->wq and use system_wq instead. Because radeon_driver_irq_uninstall_kms() may be called from unsleepable context, the work items can't be flushed from there. Instead, init and flush from radeon_irq_kms_init/fini(). While at it, simplify canceling/flushing of rdev->pm.dynpm_idle_work. Always initialize and sync cancel instead of being unnecessarily smart about it. Signed-off-by: NTejun Heo <tj@kernel.org> Acked-by: NAlex Deucher <alexdeucher@gmail.com> Cc: dri-devel@lists.freedesktop.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Dave Airlie 提交于
Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Marek Olšák 提交于
The CMASK RAM is for colorbuffer compression (used in conjunction with MSAA). Only one user (filp) can access it. The CMASK RAM access is managed in the same way as Hyper-Z, but there is a separate ioctl, because an app that uses MSAA does not necessarily have to use zbuffering. Signed-off-by: NMarek Olšák <maraeo@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Acer laptop (TravelMate 5730G) has an HDMI connector on the laptop and a DVI connector on the docking station and both share the same encoder, hpd pin, and ddc line. The bios connector table reflects this and is technically correct, however, we drop the DVI connector here since xrandr has no concept of encoders (only crtcs and connectors) and will try and drive both connectors with different crtcs which isn't possible on the hardware side and leaves no crtcs for LVDS or VGA. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=32732Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Cc: stable@kernel.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
- 05 1月, 2011 9 次提交
-
-
由 Dave Airlie 提交于
stage 1: turn card on, switch boot vga pointer. stage 2: switch fbs, switch mux and power off old card. Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Dave Airlie 提交于
We need to track the state of the switch in drivers, so that after s/r we don't resume the card we've explicitly switched off before. Also don't allow a userspace open to occur if we've switched the gpu off. Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Dave Airlie 提交于
This adds a hook after the mux is switched for the driver to reprobe the connected outputs. Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Dave Airlie 提交于
This improves the IGD/DIS picking using firstly if Intel, then if the bus is bus 0. There may be a correct way to do this, but I've no idea what it is. Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Dave Airlie 提交于
this just adds the callback on the delayed switch mechanism. Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Dave Airlie 提交于
This allows the mux to be switched from userspace using MIGD/MDIS command to the switch. Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Dave Airlie 提交于
At least on the nvidia mux the power switch seems to be executed by the ACPI PS0/PS3 methods so need to do it explicitly. Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Dave Airlie 提交于
We really want to see this so we can confirm that we pick the right one. Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Now that soft reset works, we can add this. Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-