Commit f77d55a3 ("serial: 8250_dw: get index of serial line from DT
aliases") made the serial driver now use the serial aliases to get the tty
number, pointing out that our aliases have been wrong all along.

Remove them from the DTSI and add custom ones in the relevant boards.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The NMI IRQ controller uses the standard flags definition for the IRQ level and
edges.

Use the common header to use defines instead of opaque numbers.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.

Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Prepare the device trees to use the C preprocessor.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

On the LeMaker Banana Pi, probing the external ethernet PHY connected
to the SoC's internal GMAC module sometimes fails. The PHY power
supply is handled via a GPIO-controlled regulator, and the existing
regulator startup-delay of 50000us is too short to make sure that the
PHY is always fully powered up when it is queried by phylib. Tests
have shown that to provide a reliable PHY detection, the startup-delay
has to be increased to at least 60000us. To have a certain safety margin
and to cater for manufacturing variations between different boards,
the delay gets set to 100000us as discussed on the linux-arm-kernel
mailinglist.
Signed-off-by: NKarsten Merker <merker@debian.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

During the GPL to GPL/X11 licensing migration, the GPL notice introduced
mentionned the device trees as a library, which is not really accurate. It
began to spread by copy and paste. Fix all these library mentions to reflect
the file that it's actually just a file.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Banana Pi is an A20 based development board using Raspberry Pi compatible
IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi
and stereo audio out + various expenansion headers:

http://www.lemaker.org/Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

During the GPL to GPL/X11 licensing migration, the GPL notice introduced
mentionned the device trees as a library, which is not really accurate. It
began to spread by copy and paste. Fix all these library mentions to reflect
the file that it's actually just a file.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This is a Q8 format 7 inch tablet with an Allwinner A13 SoC.
It has 512MB DRAM, 4GB NAND flash, an accelerometer, camera,
RTL8188-based WiFi, and micro SD slot for external storage.

It is likely made by a subsidiary of Hanns.G (Hannstar).
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>