Existing implementation of tegra_ehci_remove() calls
usb_put_hcd(hcd) first and then iounmap(hcd->regs).

usb_put_hcd() implementation calls hcd_release()
which frees up memory allocated for hcd.

As iounmap is trying to unmap hcd->regs, after hcd
getting freed up, warning messages were observed during
unload of USB.

Hence fixing it.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The ehci_setup() require the pointer of usb_hcd.
Passing the correct pointer in place of ehci_hcd
pointer.

This is side effect of change:
commit 1a49e2ac
Author: Alan Stern <stern@rowland.harvard.edu>

    EHCI: centralize controller initialization

[Although I checked for this specifically, obviously I missed some of
the calls.  In addition to the mistake in ehci-tegra.c that Laxman
fixed here, the same thing needs to be fixed in ehci-orion.c and
ehci-xls.c. -- Alan Stern]
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1588) adjusts the locking in ehci-hcd's various halt,
shutdown, and suspend/resume pathways.  We want to hold the spinlock
while writing device registers and accessing shared variables, but not
while polling in a loop.

In addition, there's no need to call ehci_work() at times when no URBs
can be active, i.e., in ehci_stop() and ehci_bus_suspend().

Finally, ehci_adjust_port_wakeup_flags() is called only in situations
where interrupts are enabled; therefore it can use spin_lock_irq
rather than spin_lock_irqsave.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1564c) converts the EHCI platform drivers to use the
central ehci_setup() routine for generic controller initialization
rather than each having its own idiosyncratic approach.

The major point of difficulty lies in ehci-pci's many vendor- and
device-specific workarounds.  Some of them have to be applied before
calling ehci_setup() and some after, which necessitates a fair amount
of code motion.  The other platform drivers require much smaller
changes.

One point not addressed by the patch is whether ports should be
powered on or off following initialization.  The different drivers
appear to handle this pretty much at random.  In fact it shouldn't
matter, because the hub driver turns on power to all ports when it
binds to the root hub.  Straightening that out will be left for
another day.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_get_phy will return -ENODEV if it's not able to find the phy. Hence
fixed all the callers of usb_get_phy to check for this error condition
instead of relying on a non-zero value as success condition.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add a linked list for keeping multiple PHY instances with different
types so that we can have separate USB2 and USB3 PHYs on one single
board. _get_phy_ has been changed so that the controller gets
the transceiver by type. _remove_phy_ has been added to let the phy
be removed from the phy list.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

_transceiver() in otg.c is replaced with _phy. usb_set_transceiver is
replaced with usb_add_phy to make it similar to other usb standard
function names like usb_add_hcd.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use clk_prepare/clk_unprepare as required by the generic clk framework.

Cc: stern@rowland.harvard.edu
Cc: gregkh@linuxfoundation.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.

Cc: <stable@vger.kernel.org> # v3.3
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1547) rearranges the Power Management parts of the
ehci-tegra driver to match the conventions used in other EHCI platform
drivers.  In particular, the controller should not be powered down by
the root hub's suspend routine; the controller's power level should be
managed by the controller's own PM methods.

The end result of the patch is that the standard ehci_bus_suspend()
and ehci_bus_resume() methods can be used instead of special-purpose
routines.  The driver now uses the standard dev_pm_ops methods instead
of legacy power management.  Since there is no supported wakeup
mechanism for the controller, runtime suspend is forbidden by default
(this can be overridden via sysfs, if desired).

These adjustments are needed in order to make ehci-tegra compatible
with recent changes to the USB core.  The core now checks the root
hub's status following bus suspend; if the controller is automatically
powered down during bus suspend then the check will fail and the root
hub will be resumed immediately.  Doing the controller power-down in a
separate method avoids this problem.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the SetPortFeature/USB_PORT_FEAT_ENABLE case, ehci_hub_control()
would read from status_reg, modify the value, and write the result back to
status_reg. This would clear any bits in PORT_RWC_BITS that were set in
the register. Fix this by masking these bits off before the write.

This is logically the same change as 6d5f89c7 "USB: EHCI: remove
PORT_RWC_BITS when clearing USB_PORT_FEAT_ENABLE", but applied to the
Tegra driver rather than the USB core.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ULPI PHYs have a reset signal, and different boards use a different GPIO
for this task. Add a property to device tree to represent this.

I'm not sure if adding this property to the EHCI controller node is
entirely correct; perhaps eventually we should have explicit separate
nodes for the various PHYs. However, we don't have that right now, so this
binding seems like a reasonable choice.

Cc: <devicetree-discuss@lists.ozlabs.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

In the ClearPortFeature/USB_PORT_FEAT_ENABLE case, ehci_hub_control()
would read from status_reg, clear PORT_PE, and write the result back to
status_reg. This would clear any bits in PORT_RWC_BITS that were set in
the registers. Fix this by masking these bits off before the write.

Since this masking is common across all ClearPortFeature cases, move it
into a single early location to avoid duplicating it.

Remove the same bugfix from ehci-tegra.c's tegra_ehci_hub_control(), now
that this case is correctly handled by the core.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This call is not needed; the IRQ controller should (and does) set up
interrupts correctly. set_irq_flags() isn't exported to modules, to
this also fixes compilation of ehci-tegra.c as a module.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Re-arranged EHCI generic and tegra specific functions
into two separate groups for more readability.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With this patch:
	1. Renamed structure and function names to be more meaningful.
	2. Removed unnecessary local variables.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a vbus_gpio field to platform data. This mirrors the device tree
property nvidia,vbus-gpio. This makes the VBUS GPIO handling identical
between booting with board files and device tree; the driver always does
it.

This removes the need for board files to request and initialize the GPIO
early during their boot process, perhaps even before the GPIO driver is
ready to process the request.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

This patch (as1537) adds a bit-array to ehci-hcd for keeping track of
which ports are undergoing a resume transition.  If any of the bits
are set when ehci_hub_status_data() is called, the routine will return
a nonzero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Chen Peter-B29397 <B29397@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.

Includes fixes to IMX code from Sascha Hauer.

[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Acked-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: NLi Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.

Includes fixes from Sascha Hauer.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: NLi Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is the first step in separating USB transceivers from
USB OTG utilities.

Includes fixes to IMX code from Sascha Hauer.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: NLi Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Rely on platform_data being passed through auxdata for now; more elaborate
bindings for phy config and tunings to be added.

v2: moved vbus-gpio check to the helper function, added check for !of_node,
    added usb2 clock to board-dt table.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

This flag is a NOOP and can be removed now.
Signed-off-by: NYong Zhang <yong.zhang0@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.

This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Tegra USB1 port needs to issue Port Reset twice internally, otherwise it
fails to enumerate devices attached to it
Signed-off-by: NJim Lin <jilin@nvidia.com>
Signed-off-by: NOlof Johansson <olofj@chromium.org>
[ squash two patches into one and minor style cleanups ]
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Tegra2 USB controller doesn't properly deal with misaligned DMA
buffers, causing corruption.  This is especially prevalent with USB
network adapters, where skbuff alignment is often in the middle of a
4-byte dword.

To avoid this, allocate a temporary buffer for the DMA if the provided
buffer isn't sufficiently aligned.
Signed-off-by: NRobert Morell <rmorell@nvidia.com>
Signed-off-by: NBenoit Goby <benoit@android.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.

The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: NBenoit Goby <benoit@android.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>