Make sure fifo is emptied on close.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On errors the fifo was reset without any locking. This could race with
write which do kfifo_put and perhaps also chars_in_buffer and write_room.

Every other access to the fifo is protected using the port lock so
better add it to the error path as well.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure chars_in_buffer accounts also for data in host stack queues.

This fixes the problem with tty_wait_until_sent returning too soon at
close which could cause the final write urb to be cancelled.
Reported-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The pl2303 requires a bulk-in buffer larger than endpoint size to keep
up at high baudrates without loosing data.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Increase the bulk-out buffer size from 64 to 256 byte.

This gives a significant increase in throughput already at 1Mbaud as well
as lowered CPU usage. The buffer is big enough to keep up also at 3Mbaud
(128b would not suffice).

        64b         256b
921k:   640 KB/s    870 KB/s
3M:     640 KB/s    2520 KB/s
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The cp210x requires a bulk-in buffer larger than endpoint size to keep
up at high baudrates without loosing data.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Increase the bulk-out buffer size from 64 to 256 byte.

This gives a significant increase in throughput already at 1Mbaud
(e.g. 710 instead of 640 KB/s) as well as lowered CPU usage.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allow drivers to define custom bulk in/out buffer sizes in struct
usb_serial_driver. If not set, fall back to the default buffer size
which matches the endpoint size.

Three drivers are currently freeing the pre-allocated buffers and
allocating larger ones to achieve this at port probe (ftdi_sio) or even
at port open (ipaq and iuu_phoenix), which needless to say is suboptimal.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a new quirk USB_QUIRK_HONOR_BNUMINTERFACES, when this quirk is
set and a device has more interface descriptors in a configuration
then it claims to have in config->bNumInterfaces, ignore all additional
interfaces.

This is needed for devices which try to hide unused interfaces by only
lowering config->bNumInterfaces, and which can't handle if you try to talk
to the "hidden" interfaces.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix build error when CONFIG_MAGIC_SYSRQ is not enabled:

drivers/usb/serial/generic.c:566: error: implicit declaration of function 'handle_sysrq'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add ZIO Motherboard USB serial interface driver.
Signed-off-by: NVijay Kumar B. <vijaykumar@zilogic.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb console code has had a long standing problem of not being able
to pass the baud rate from the kernel argument console=ttyUSB0,BAUD
down to the initial tty open, unless you were willing to settle for
9600 baud.

The solution is to directly use tty_init_termios() in
usb_console_setup() as this will preserve any changes to the initial
termios setting on future opens.

CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

"Static" buffers in fsg_buffhd structure (ie. fields which are arrays
rather then pointers to dynamically allocated memory) are not aligned
to any "big" power of two which may lead to poor DMA performance
(copying "by hand" of head or tail) or no DMA at all even if otherwise
hardware supports it.

Therefore, this patch makes mass storage function use kmalloc()ed
buffers which are (because of their size) page aligned (which should
be enough for any hardware).
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

... and simplify the was we read/write from/to
DMA COUNT register.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

we can support the musb-specific test modes on the
vendor specific range of test selector as stated
on USB Specification Table 9-7 Test Mode Selectors.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

for now only a simple register dump entry (which can
be rather useful on debugging) and a way to start
test modes.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Rather than hardcoding the gpio levels for vrsel, allow the platform
resources to handle this so boards can be active high or low.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds CONFIG_ARCH_OMAP4 macro within
MUSB driver.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch updates the Makefile to build the
MUSB driver for OMAP4. It also sets the Kconfig
options for OMAP4.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Program the OTG_INTERFSEL register based on
transcevier type passed from board file.

Adapt signature of musb_platform_init() function
for davinci, blackfin and tusb6010.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

boards might want to optimize their fifo configuration
to the particular needs of that specific board. Allow
that by moving all related data structures to
<linux/usb/musb.h>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace all instances of using the console variable in struct
usb_serial_port with the struct tty_port version.

CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I've been running variations of this patch for well over a year now;
my usual zoo of test devices didn't trigger any ill effects even
under heavy load.  As a nice sideeffect idle-wakeups are reduced
from 20/s to about 2/s (EHCI hub with mouse and kbd).
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1350) removes all usages of coherent buffers for USB
control-request setup-packet buffers.  There's no good reason to
reserve coherent memory for these things; control requests are hardly
ever used in large quantity (the major exception is firmware
transfers, and they aren't time-critical).  Furthermore, only seven
drivers used it.  We might as well always use streaming DMA mappings
for setup-packet buffers, and remove some extra complexity from
usbcore.

The DMA-mapping portion of hcd.c is currently in flux.  A separate
patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP
after everything else settles down.  The removal should go smoothly,
as by then nobody will be using it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1349b) clears up the confusion in many USB host
controller drivers between port features and port statuses.  In mosty
cases it's true that the status bit is in the position given by the
corresponding feature value, but that's not always true and it's not
guaranteed in the USB spec.

There's no functional change, just replacing expressions of the form
(1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1348) removes the bogus
USB_PORT_FEAT_{HIGHSPEED,SUPERSPEED} symbols from ch11.h.  No such
features are defined by the USB spec.  (There is a PORT_LOWSPEED
feature, but the spec doesn't mention it except to say that host
software should never use it.)  The speed indicators are port
statuses, not port features.

As a temporary workaround for the xhci-hcd driver, a fictional
USB_PORT_STAT_SUPER_SPEED symbol is added.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove duplicated #include('s) in
  drivers/usb/core/hcd.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The compiler throws the following warning when compiling for a PowerPC 64
bit machine:

drivers/usb/storage/isd200.c:580: warning: the frame size of 2208 bytes is larger than 2048 bytes

There is a struct scsi_device which is placed on the stack and is
largely responsible for such wastage. The struct is just a dummy struct
filled with NULLs and set as the scsi_cmnd->device to make the
usb_stor_Bulk_transport function happy.

This patch makes the struct static, so that it is never placed onto the
stack and silences the compiler warning.
Signed-off-by: NIan Munsie <imunsie@au.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix usb/class sparse warnings:

drivers/usb/class/cdc-acm.h:128:34: error: dubious one-bit signed bitfield
drivers/usb/class/cdc-acm.h:129:24: error: dubious one-bit signed bitfield
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Seems to me that BKL is not needed here because necessary locking is already
provided by mutex sisusb->lock.

Also change the returned value to long.
Signed-off-by: NAlessio Igor Bogani <abogani@texware.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Base on inputs from Alan Stern, split the hub.h header into:
- new ch11.h header (most of it) containing constants and
  structures from chapter 11 of the USB 2.0 spec.
- a small remaining part being merged into hcd.h.
Signed-of-by: NEric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hub.h from drivers/usb/core into include/linux/usb/
Signed-of-by: NEric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: NEric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The length of the scatter gather list a driver can enqueue is limited by
the bus' sg_tablesize to 62 entries.  Each entry will be described by at
least one transfer request block (TRB).  If the entry's buffer crosses a
64KB boundary, then that entry will have to be described by two or more
TRBs.  So even if the USB device driver respects sg_tablesize, the whole
scatter list may take more than 62 TRBs to describe, and won't fit on
the ring.

Don't assume that an empty ring means there is enough room on the
transfer ring.  The old code would unconditionally queue this too-large
transfer, and over write the beginning of the transfer.  This would mean
the cycle bit was unchanged in those overwritten transfers, causing the
hardware to think it didn't own the TRBs, and the host would seem to
hang.

Now drivers may see submit_urb() fail with -ENOMEM if the transfers are
too big to fit on the ring.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a scatter-gather list is enqueued to the xHCI driver, it translates
each entry into a transfer request block (TRB).  Only 63 TRBs can be
used per ring segment, and there must be one additional TRB reserved to
make sure the hardware does not think the ring is empty (so the enqueue
pointer doesn't equal the dequeue pointer).  Limit the bus sg_tablesize
to 62 TRBs.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the USB core installs a new interface, it unconditionally clears the
halts on all the endpoints on the new interface.  Usually the xHCI host
needs to know when an endpoint is reset, so it can change its internal
endpoint state.  In this case, it doesn't care, because the endpoints were
never halted in the first place.

To avoid issuing a redundant Reset Endpoint command, the xHCI driver looks
at xhci_virt_ep->stopped_td to determine if the endpoint was actually
halted.  However, the functions that handle the stall never set that
variable to NULL after it dealt with the stall.  So if an endpoint stalled
and a Reset Endpoint command completed, and then the class driver tried to
install a new alternate setting, the xHCI driver would access the old
xhci_virt_ep->stopped_td pointer.  A similar problem occurs if the
endpoint has been stopped to cancel a transfer.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  rtnetlink: make SR-IOV VF interface symmetric
  sctp: delete active ICMP proto unreachable timer when free transport
  tcp: fix MD5 (RFC2385) support

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Oprofile: Fix Loongson irq handler
  MIPS: N32: Use compat version for sys_ppoll.
  MIPS FPU emulator: allow Cause bits of FCSR to be writeable by ctc1

Now we have a set of nested attributes:

  IFLA_VFINFO_LIST (NESTED)
    IFLA_VF_INFO (NESTED)
      IFLA_VF_MAC
      IFLA_VF_VLAN
      IFLA_VF_TX_RATE

This allows a single set to operate on multiple attributes if desired.
Among other things, it means a dump can be replayed to set state.

The current interface has yet to be released, so this seems like
something to consider for 2.6.34.
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>