Unfortunately ath10k does not generally allow modifying the coverage class
with the stock firmware and Qualcomm has so far refused to implement this
feature so that it can be properly supported in ath10k. If we however know
the registers that need to be modified for proper operation with a higher
coverage class, then we can do these modifications from the driver.

This is a hack and might cause subtle problems but as it's not enabled by
default (only when user space changes the coverage class explicitly) it should
not cause new problems for existing setups. But still this should be considered
as an experimental feature and used with caution.

This patch implements the support for first generation cards (QCA9880, QCA9887
and so on) which are based on a core that is similar to ath9k. The registers
are modified in place and need to be re-written every time the firmware sets
them. To achieve this the register status is verified after certain WMI events
from the firmware.

The coverage class may not be modified temporarily right after the card
re-initializes the registers. This is for example the case during scanning.

Thanks to Sebastian Gottschall <s.gottschall@dd-wrt.com> for initially
working on a userspace support for this. This patch wouldn't have been
possible without this documentation.
Signed-off-by: NBenjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This overrides whatever regulatory the device
EEPROM contains and uses what the platform says
instead - in this implementation the ACPI driver.

In case the hint is not programmed or corrupted (0xffff)
the device falls back to the eeprom programmed settings.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
[kvalo@qca.qualcomm.com: remove ifdef, change error handling, change info messages to dbg]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

They are not necessarily named in an intuitive manner,
so at least add some comments to help the next person.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to prepare for rx descriptor abstraction where we'll
be dereferencing ath10k_hw_params member in hw.h. Moreover
hw.h looks more suitable to house ath10k_hw_params definition
than core.h
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add NAPI support for rx and tx completion. NAPI poll is scheduled
from interrupt handler. The design is as below

 - on interrupt
     - schedule napi and mask interrupts
 - on poll
   - process all pipes (no actual Tx/Rx)
   - process Rx within budget
   - if quota exceeds budget reschedule napi poll by returning budget
   - process Tx completions and update budget if necessary
   - process Tx fetch indications (pull-push)
   - push any other pending Tx (if possible)
   - before resched or napi completion replenish htt rx ring buffer
   - if work done < budget, complete napi poll and unmask interrupts

This change also get rid of two tasklets (intr_tq and txrx_compl_task).

Measured peak throughput with NAPI on IPQ4019 platform in controlled
environment. No noticeable reduction in throughput is seen and also
observed improvements in CPU usage. Approx. 15% CPU usage got reduced
in UDP uplink case.

DL: AP DUT Tx
UL: AP DUT Rx

IPQ4019 (avg. cpu usage %)

========
                TOT              +NAPI
              ===========      =============
TCP DL       644 Mbps (42%)    645 Mbps (36%)
TCP UL       673 Mbps (30%)    675 Mbps (26%)
UDP DL       682 Mbps (49%)    680 Mbps (49%)
UDP UL       720 Mbps (28%)    717 Mbps (11%)
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Older firmware with HTT delivers incorrect tx status for null func
frames to driver, but this fixed in 10.2 and 10.4 firmware versions.
Also this workaround results in reporting of incorrect null func status
for 10.4. Fix this is by introducing a firmware feature flag for 10.4
so that this workaround is skipped and proper tx status for null func
frames are reported
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For 10.4 fw versions, dbglog module id has been extended from u32
to u64, hence this patch fixes the same in the ath10k driver side.

This patch doesn't break the older 10.4 releases. The FW change
is already present in the older FWs.
Signed-off-by: NMaharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Recent commit 46f6b060 ("mac80211: Encrypt "Group addressed privacy" action
frames") encrypts group privacy action frames. But qca99x0 family chipset
delivers broadcast/multicast management frames as encrypted and it should be
decrypted by mac80211. Setting RX_FLAG_DECRYPTED stats for those frames is
breaking mesh connection establishment.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This allows placing command barriers for explicit
serializing and synchronizing state.

Useful for future driver development.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation to make use of firmware_swap_code_seg_info for UTF binary.
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Ideally wake_tx_queue should be used regardless as
it is a requirement for reducing bufferbloat and
implementing airtime fairness in the future.

However some setups (typically low-end platforms
hosting QCA988X) suffer performance regressions
with the current wake_tx_queue implementation.
Therefore disable it unless it is really
beneficial with current codebase (which is when
firmware supports smart pull-push tx scheduling).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 'extended peer stats' will be not be appended with normal peer stats
data and they shall be coming in separate chunks. Fix this by maintaining
a separate linked list 'extender peer stats' for 10.4 and update
rx_duration for per station statistics. Also parse through beacon filter
(if enabled), to make sure we parse the extended peer stats properly.
This issue was exposed when more than one client is connected and
extended peer stats for 10.4 is enabled

The order for the stats is as below
S - standard peer stats, E- extended peer stats, B - beacon filter stats

{S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..}

Fixes: f9575793 ("ath10k: enable parsing per station rx duration for 10.4")
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA988X hw implements a different cycle counter wraparound
behaviour when compared to QCA4019. To properly handle different
wraparound logic for these chipsets replace already available
bool hw_params member, has_shifted_cc_wraparound, with an
enum which could be extended to handle different wraparound
behaviour. This patch keeps the existing logic functionally
same and a prepares cycle counter wraparound handling to
extend for other chips.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: change also QCA9887 wrap type]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

CCK hardware table mapping from QCA99X0 onwards got revised.
The CCK hardware rate values are in a proper order wrt. to
rate and preamble as below

ATH10K_HW_RATE_REV2_CCK_LP_1M = 1,
ATH10K_HW_RATE_REV2_CCK_LP_2M = 2,
ATH10K_HW_RATE_REV2_CCK_LP_5_5M = 3,
ATH10K_HW_RATE_REV2_CCK_LP_11M = 4,
ATH10K_HW_RATE_REV2_CCK_SP_2M = 5,
ATH10K_HW_RATE_REV2_CCK_SP_5_5M = 6,
ATH10K_HW_RATE_REV2_CCK_SP_11M = 7,

This results in reporting of rx frames (with CCK rates)
totally wrong for QCA99X0, QCA4019. Fix this by having
separate CCK rate table for these chipsets with rev2 suffix
and registering the correct rate mapping to mac80211 based on
the new hw_param (introduced) 'cck_rate_map_rev2' which shall
be true for any newchipsets from QCA99X0 onwards
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The QCA9887 stores its calibration data (board.bin) inside the EEPROM of
the target. This has to be downloaded manually to allow the device to
initialize correctly.
Signed-off-by: NSven Eckelmann <sven.eckelmann@open-mesh.com>
[kvalo@qca.qualcomm.com: handle -EOPNOTSUPP and s/fetch_board_data/fetch_cal_eeprom]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This feature flag will be used for firmware to support BT-Coex feature
without reloading firmware via WMI pdev param. To support Bluetooth
coexistence pdev param, WMI_COEX_GPIO_SUPPORT of extended resource
config should be enabled always. This firmware IE is used to configure
WMI_COEX_GPIO_SUPPORT.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During hw scan, firmware sends two channel information events (pre-
complete, complete) to host for each channel change. The snap shot of cycle
counters (rx_clear and total) between these two events are given for
survey dump. In order to get latest survey statistics of all channels, a
scan request has to be issued. In general, an AP DUT is brought up, it
won't leave BSS channel except few cases like overlapping bss or radar
detection. So survey statistics of bss channel is always referring to
older data that are collected before starting AP (either ACS/OBSS scan).

To collect latest survey information from target, firmware provides WMI
interface to read cycle counters from hardware. For each survey dump
request, BSS channel cycle counters are read and cleared in hardware.
This makes sure that behavior is in align with ath9k survey report.
So survey dump always gives snap shot of cycle counters b/w two survey
requests.
Signed-off-by: NYanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Spectral related structures are accessed / modified only if ath10k
debugfs is enabled, so it makes more sense to move them under
ATH10K_DEBUGFS
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now that all firmware-N.bin related are within struct ath10k_fw_file we can
switch to use ath10k_core_fetch_firmware_api_n() and delete almost identical
ath10k_tm_fetch_utf_firmware_api_2().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To make it easier to share ath10k_core_fetch_board_data_api_n() with testmode.c
refactor all firmware components to struct ath10k_fw_components. This structure
will hold firmware related files, for example firmware-N.bin and board-N.bin.

For firmware-N.bin create a new struct ath10k_fw_file which contains the actual
firmware image as well as the parsed data from the image.

Modify ath10k_core_start() to take struct ath10k_fw_components() as an argument
which makes it possible in following patches to drop some ugly hacks from
testmode.c.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This has ben deprecated years ago, I haven't heard anyone using it since and
most likely it won't even work anymore. So just remove all of it.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix checkpatch warnings about use of spaces with operators:

spaces preferred around that '*' (ctx:VxV)

This has been recently added to checkpatch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

pre-calibration is meant for qca4019 which contains only caldata
whereas calibration file is used by ar9888 and qca99x0 that contains
both board data and caldata. So by definition both pre-cal-file and
cal-file can not coexist. Keeping them in shared memory (union), is
breaking boot sequence of qca99x0. Fix it by storing both binaries
in separate memories. This issue is reported in ipq8064 platform which
includes caldata in flash memory.

Fixes: 3d9195ea ("ath10k: incorporate qca4019 cal data download sequence")
Reported-by: NSebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Provide a debugfs entry to enable/ disable Peer Stats feature.
Peer Stats feature is for developers/users who are more interested
in studying in Rx/Tx stats with multiple clients connected, hence
disable this by default. Enabling this feature by default results
in unneccessary processing of Peer Stats event for every 500ms
and updating peer_stats list (allocating memory) and cleaning it up
ifexceeds the higher limit and this can be an unnecessary overhead
during long run stress testing.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca4019 calibration data is stored in the host memory and it's mandatory
to download it even before reading board id and chip id from the target.
Also, there is a need to execute otp (download and run) twice, one after
cal data download and another one after board data download.

Existing cal data file name 'cal-<bus>-<id>.bin' and device tree entry
'qcom,ath10k-calibration-data' used in ath10k has assumption that it
carries other data (like board data) also along with the calibration data.
But, qca4019 cal data contains pure calibration data (doesn't include
any other info). So, using existing same cal file name and DT entry
in qca4019 case would alter the purpose of it. To avoid this, new cal
file name 'pre-cal-<bus>-<id>.bin' and new device tree entry name
'qcom,ath10k-pre-calibration-data are introduced.

Overall qca4019's firmware download sequence would look like,

   1) Download cal data (either from a file or device tree entry)
      at the address specified by target in the host interest area
      member "hi_board_data".

   2) Download otp and run with 0x10 (PARAM_GET_EEPROM_BOARD_ID)
      as a argument.

      At this point, otp will take back up of downloaded cal data
      content in another location in the target and return valid
      board id and chip id to the host.

   3) Download board data at the address specified by target
      in host interest area member "hi_board_data".

   4) Download otp and run with 0x10000 (PARAM_FLASH_SECTION_ALL) as
      a argument.

      Now otp will apply cal data content from it's backup on top
      of board data download in step 3 and prepare final data base.

   5) Download code swap and athwlan binary content.

Above sequences are implemented (step 1 to step 4) in the name of
pre calibration configuration.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_download_cal_dt() compares obtained cal data content length
against QCA988X_CAL_DATA_LEN (2116 bytes). It was written by keeping
qca988x in mind. In fact, cal data length is more chip specific.
To make ath10k_download_cal_dt() more generic and reusable for other
chipsets (like qca4019), cal data length is moved to hw_params.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Whenever firmware is configuring operating channel during scan or
home channel, channel change event will be indicated to host. In some
cases (device probe/ last vdev down), target will be configured to
default channel whereas host is unaware of target's operating channel.
This leads to packet drop due to unknown channel and kernel log will be
filled up with "no channel configured; ignoring frame(s)!". Fix that
by handling HTT_T2H_MSG_TYPE_CHAN_CHANGE event.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The number of HTT Tx descriptors and qcache peer
limit aren't hw-specific. In fact they are
firmware specific and should not be placed in
hw_params.

The QCA4019 limits were submitted with the peer
flow control firmware only and to my understanding
there's no non-peer-flow-ctrl QCA4019 firmware.

However QCA99X0 is planned to run firmware
supporting the feature as well. Therefore this
patch enables QCA99X0 to use 2500 tx descriptors
whenever possible instead of just 1424.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The current/old tx path design was that host, at
its own leisure, pushed tx frames to the device.
For HTT there was ~1000-1400 msdu queue depth.

After reaching that limit the driver would request
mac80211 to stop queues. There was little control
over what packets got in there as far as
DA/RA was considered so it was rather easy to
starve per-station traffic flows.

With MU-MIMO this became a significant problem
because the queue depth was insufficient to buffer
frames from multiple clients (which could have
different signal quality and capabilities) in an
efficient fashion.

Hence the new tx path in 10.4 was introduced: a
pull-push mode.

Firmware and host can share tx queue state via
DMA. The state is logically a 2 dimensional array
addressed via peer_id+tid pair. Each entry is a
counter (either number of bytes or packets. Host
keeps it updated and firmware uses it for
scheduling Tx pull requests to host.

This allows MU-MIMO to become a lot more effective
with 10+ clients.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will be necessary for later.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will be necessary for later.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This implements very basic support for software
queueing. It also contains some knobs that will be
patched later.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The pull-push functionality of 10.4 will be based
on peer_id and tid. These will need to be mapped,
eventually, to ieee80211_txq to be used with
ieee80211_tx_dequeue().

Iterating over existing stations every time
peer_id needs to be mapped to a station would be
inefficient wrt CPU time.

The new firmware, which will be the only user of
the code flow-wise, will guarantee to use low
peer_ids first so despite peer_map's apparent huge
size d-cache thrashing should not be a problem.

Older firmware hot paths will effectively not use
peer_map.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The 10.4.3 firmware with congestion control
guarantees that each peer has only a single
peer_id mapping.

The 1:1 mapping isn't the case for older firmwares
(e.g. 10.4.1, 10.2, 10.1) but it should not
matter. This 1:1 mapping is going to be only used
by future code which inherently (flow-wise) is for
10.4.3.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some of the parameter like tx/rx chain mask, number of htt tx desc,
qcache active peer count, etc goes via wmi init cmd to qca4019 firmware
are different.

To make use of 10.4 gen_init function for qca4019, change wmi service
ready handler and 10.4 wmi init functions to adapt qca4019 specific
init values.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>