Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1451427643-7266-1-git-send-email-benjamin.widawsky@intel.comSigned-off-by: NJani Nikula <jani.nikula@intel.com>

The total delay of HDMI hotplug detecting with 30ms is sometimes not
enoughtfor HDMI live status up with specific HDMI monitors in BSW platform.

After doing experiments for following monitors, it needs 80ms at least
for those worst cases.

Lenovo L246 1xwA (4 failed, necessary hot-plug delay: 58/40/60/40ms)
Philips HH2AP (9 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms)
BENQ ET-0035-N (6 failed, necessary hot-plug delay: 60/50/50/80/80/40ms)
DELL U2713HM (2 failed, necessary hot-plug delay: 58/59ms)
HP HP-LP2475w (5 failed, necessary hot-plug delay: 70/50/40/60/40ms)

It looks like 70-80 ms is BSW platform needs in some bad cases of the
monitors at this end (8 times delay at most). Keep less than 100ms for
HDCP pulse HPD low (with at least 100ms) to respond a plug out.
Reviewed-by: NCooper Chiou <cooper.chiou@intel.com>
Tested-by: NGary Wang <gary.c.wang@intel.com>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NGary Wang <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450858295-12804-1-git-send-email-gary.c.wang@intel.comTested-by: NShobhit Kumar <shobhit.kumar@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 237ed86c ("drm/i915: Check live status before reading edid")
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When the crtc is configured but not active we currently clip to (0,0)x(0,0).
This results in differences in calculations depending on dpms setting.
When the crtc is enabled but not active run check_plane as if it were on,
but afterwards set plane_state->visible = false for the checks.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447945645-32005-13-git-send-email-maarten.lankhorst@linux.intel.com

On skylake when calculating plane visibility with the crtc in
dpms off mode the real cdclk may be different from what it would be
if the crtc was active. This may result in a WARN_ON(cdclk < crtc_clock)
from skl_max_scale. The fix is to keep a atomic_cdclk that would be true
if all crtc's were active.

This is required to get the same calculations done correctly regardless
of dpms mode.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447945645-32005-12-git-send-email-maarten.lankhorst@linux.intel.com

Parallel modesets are still not allowed, but this will allow updating
a different crtc during a modeset if the clock is not changed.

Additionally when all pipes are DPMS off the cdclk will be lowered
to the minimum allowed.

Changes since v1:
- Add dev_priv->active_crtcs for tracking which crtcs are active.
- Rename min_cdclk to min_pixclk and move to dev_priv.
- Add a active_crtcs mask which is updated atomically.
- Add intel_atomic_state->modeset which is set on modesets.
- Commit new pixclk/active_crtcs right after state swap.
Changes since v2:
- Make the changes related to max_pixel_rate calculations more readable.
Changes since v3:
- Add cherryview and missing WARN_ON to readout.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMika Kahola <mika.kahola@intel.com>

This fixes a warning when the crtc is turned off. In that case fb
will be NULL, and crtc_clock will be 0. Because the crtc is no longer
active this is not a bug, and shouldn't trigger the WARN_ON.

Also remove handling a null crtc_state, with all transitional helpers
gone this can no longer happen.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448360945-5723-2-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>

Add an overview and documentation for the VBT/BDB header structures.
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/3d826d4600688ca3518713776ab5bd8a8fc9f20f.1450702954.git.jani.nikula@intel.com

Atomic changes broke check_digital_port_conflicts(). It needs to look
at the global situation instead of just trying to find a conflict
within the current atomic state.

This bug made my HSW explode spectacularly after I had split the DDI
encoders into separate DP and HDMI encoders. With the fix, things
seem much more solid.

I hope holding the connection_mutex is enough protection that we can
actually walk the connectors even if they're not part of the current
atomic state...

v2: Regenerate the patch so that it actually applies (Jani)

Cc: stable@vger.kernel.org
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Fixes: 5448a00d ("drm/i915: Don't use staged config in check_digital_port_conflicts()")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449764551-12466-1-git-send-email-ville.syrjala@linux.intel.comSigned-off-by: NJani Nikula <jani.nikula@intel.com>

Using __stringify(x) instead of #x adds support for macros as
a parameter and compile-time concatenation reduces the runtime
overhead.

Slightly increases the .text size but should not matter.

v2:
- Define I915_STATE_WARN_ON though I915_STATE_WARN
  (Bikeshed inspiration by Chris)

v3:
- More specific commit message

v4:
- Do not directly pass arbitary string as format, instead
  guard with "%s" (Dave)

Cc: Rob Clark <robdclark@gmail.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450441647-23924-3-git-send-email-joonas.lahtinen@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Take advantage of WARN return value to simplify the flow.

Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450441647-23924-2-git-send-email-joonas.lahtinen@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Clean up after 0c82312f ("drm/i915: Pin the ifbdev for the
info->system_base GGTT mmapping"):

At each of the remaining "goto out" in intelfb_alloc(), fb can only be
either an ERR_PTR or NULL, so the call to drm_framebuffer_unreference()
is now obsolete.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Link: http://patchwork.freedesktop.org/patch/msgid/56756c41.c306c20a.d0602.1830SMTPIN_ADDED_MISSING@mx.google.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Turns out CHV pipe C was glued on somewhat poorly, and there's something
wrong with the cursor. If the cursor straddles the left screen edge,
and is then moved away from the edge or disabled, the pipe will often
underrun. If enough underruns are triggered quickly enough the pipe
will fall over and die (it just scans out a solid color and reports
a constant underrun). We need to turn the disp2d power well off and
on again to recover the pipe.

None of that is very nice for the user, so let's just refuse to place
the cursor in the compromised position. The ddx appears to fall back
to swcursor when the ioctl returns an error, so theoretically there's
no loss of functionality for the user (discounting swcursor bugs).
I suppose most cursors images actually have the hotspot not exactly
at 0,0 so under typical conditions the fallback will in fact kick in
as soon as the cursor touches the left edge of the screen.

Any atomic compositor should anyway be prepared to fall back to
GPU composition when things don't work out, so there should be no
problem with those.

Other things that I tried to solve this include flipping all
display related clock gating knobs I could find, increasing the
minimum gtt alignment all the way up to 512k. I also tried to see
if there are more specific screen coordinates that hit the bug, but
the findings were somewhat inconclusive. Sometimes the failures
happen almost across the whole left edge, sometimes more at the very
top and around the bottom half. I wasn't able to find any real pattern
to these variations, so it seems our only choice is to just refuse
to straddle the left screen edge at all.

Cc: stable@vger.kernel.org
Cc: Jason Plum <max@warheads.net>
Testcase: igt/kms_chv_cursor_fail
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92826Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450459479-16286-1-git-send-email-ville.syrjala@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move all the bool variables to the end as per the comment.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450436898-20408-3-git-send-email-joonas.lahtinen@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise usage in the i915 debug macros yields problems due to
i915_drv.h <-> i915_trace.h <-> intel_drv.h include loops.

v2:
- Document not-so-obvious need for linux/cache.h (Chris)
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450436898-20408-2-git-send-email-joonas.lahtinen@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It is unclear if this is even required on BXT.

v2: Make sure to set the default value to false. Uncertain how my compiler
doesn't complain with v1.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450374597-7021-1-git-send-email-benjamin.widawsky@intel.comReviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The total delay of HDMI hotplug detecting with 30ms have already
been split into a resolution of 3 retries of 10ms each, for the worst
cases. But it still suffered from only waiting 10ms at most in
intel_hdmi_detect(). This patch corrects it by reading hotplug status
with 4 times at most for 30ms delay.

v2:
- straight up to loop execution for more clear in code readability
- mdelay will replace with msleep by Daniel's new patch

	drm/i915: mdelay(10) considered harmful

- suggest to re-evaluate try times for being compatible to old HDMI monitor
Reviewed-by: NCooper Chiou <cooper.chiou@intel.com>
Tested-by: NGary Wang <gary.c.wang@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NGary Wang <gary.c.wang@intel.com>
[danvet: fixup conflict with s/mdelay/msleep/ patch.]
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There was a silent conflict between

commit 0a878716
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Thu Oct 15 14:23:01 2015 +0200

    drm/i915: restore ggtt double-bind avoidance

and

commit 5bab6f60
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Fri Oct 23 18:43:32 2015 +0100

    drm/i915: Serialise updates to GGTT with access through GGTT on Braswell

thankfully caught by the extra WARN safegaurd in 0a878716. Since we now
override the GGTT insert_pages callback when installing the aliasing
ppgtt, we assert that the callback is the original ggtt routine.
However, on Braswell we now use a different insertion routine to
serialise access through the GGTT with updating the PTE and hence the
conflict. To avoid the conflict, move the custom insertion routine for
Braswell down a level.

Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447859979-20107-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

commit 344df980 ("drm/i915/skl: Disable coarse power gating up until F0")
failed to take into account that the same workaround is used in guc
when forcewake is sampled.

Wrap the condition check inside a macro and use it in both places
to fix the guc side scope.

Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450286318-6854-1-git-send-email-mika.kuoppala@intel.com

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The workarounds for disabling hdc invalidation and also forcing
context to be non coherent, are advised to be used up until rev D0.

However as it was found that rev F0, without the
WaForceEnableNonCoherent might system hang if the mesa
tried to use coherent mode.

As these two workarounds are about non coherent access, are
grouped in scope and they point the same HSD, increase the
scope of both to set default behaviour to non coherent access.

References: HSD: gen9lp/2131413
References: http://lists.freedesktop.org/archives/mesa-dev/2015-November/101515.html
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450448093-22906-1-git-send-email-mika.kuoppala@intel.com

Limit busywaiting only to the request currently being processed by the
GPU. If the request is not currently being processed by the GPU, there
is a very low likelihood of it being completed within the 2 microsecond
spin timeout and so we will just be wasting CPU cycles.

v2: Check for logical inversion when rebasing - we were incorrectly
checking for this request being active, and instead busywaiting for
when the GPU was not yet processing the request of interest.

v3: Try another colour for the seqno names.
v4: Another colour for the function names.

v5: Remove the forced coherency when checking for the active request. On
reflection and plenty of recent experimentation, the issue is not a
cache coherency problem - but an irq/seqno ordering problem (timing issue).
Here, we do not need the w/a to force ordering of the read with an
interrupt.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-4-git-send-email-chris@chris-wilson.co.uk

When waiting for high frequency requests, the finite amount of time
required to set up the irq and wait upon it limits the response rate. By
busywaiting on the request completion for a short while we can service
the high frequency waits as quick as possible. However, if it is a slow
request, we want to sleep as quickly as possible. The tradeoff between
waiting and sleeping is roughly the time it takes to sleep on a request,
on the order of a microsecond. Based on measurements of synchronous
workloads from across big core and little atom, I have set the limit for
busywaiting as 10 microseconds. In most of the synchronous cases, we can
reduce the limit down to as little as 2 miscroseconds, but that leaves
quite a few test cases regressing by factors of 3 and more.

The code currently uses the jiffie clock, but that is far too coarse (on
the order of 10 milliseconds) and results in poor interactivity as the
CPU ends up being hogged by slow requests. To get microsecond resolution
we need to use a high resolution timer. The cheapest of which is polling
local_clock(), but that is only valid on the same CPU. If we switch CPUs
because the task was preempted, we can also use that as an indicator that
 the system is too busy to waste cycles on spinning and we should sleep
instead.

__i915_spin_request was introduced in
commit 2def4ad9 [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Apr 7 16:20:41 2015 +0100

     drm/i915: Optimistically spin for the request completion

v2: Drop full u64 for unsigned long - the timer is 32bit wraparound safe,
so we can use native register sizes on smaller architectures. Mention
the approximate microseconds units for elapsed time and add some extra
comments describing the reason for busywaiting.

v3: Raise the limit to 10us
v4: Now 5us.
Reported-by: NJens Axboe <axboe@kernel.dk>
Link: https://lkml.org/lkml/2015/11/12/621Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-3-git-send-email-chris@chris-wilson.co.uk

The busywait in __i915_spin_request() does not respect pending signals
and so may consume the entire timeslice for the task instead of
returning to userspace to handle the signal.

In the worst case this could cause a delay in signal processing of 20ms,
which would be a noticeable jitter in cursor tracking. If a higher
resolution signal was being used, for example to provide fairness of a
server timeslices between clients, we could expect to detect some
unfairness between clients (i.e. some windows not updating as fast as
others). This issue was noticed when inspecting a report of poor
interactivity resulting from excessively high __i915_spin_request usage.

Fixes regression from
commit 2def4ad9 [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Apr 7 16:20:41 2015 +0100

     drm/i915: Optimistically spin for the request completion

v2: Try to assess the impact of the bug
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc; "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-2-git-send-email-chris@chris-wilson.co.uk

pm_runtime_{use,dont_use}_autosuspend() controls whether the device's
sysfs power/autosuspend_delay_ms file is writeable or returns -EIO on
access to user space. Since

commit 25b181b4
Author: Imre Deak <imre.deak@intel.com>
Date:   Thu Dec 17 13:44:56 2015 +0200

  drm/i915: get a permanent RPM reference on platforms w/o RPM support

this sysfs file is writeable also on platforms without RPM support, but
userspace (at least IGT) depends on this file being unchangable to
determine whether the device supports runtime PM at all. So restore the
old behavior.

This gets rid of igt/pm_rpm failures on old platforms without RPM
support, where the test should be skipped.

Testcase: igt/pm_rpm/basic-rte
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450371873-878-1-git-send-email-imre.deak@intel.com

Use dev_priv rather than dev pointer where applicable. Remove plenty of
unnecessary temp variables. No functional changes.
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450428695-28831-1-git-send-email-jani.nikula@intel.com

If we fail to reconstruct the BIOS fb (e.g., because the FB is too
large), we'll be left with plane state that indicates the primary plane
is visible yet has a NULL fb.  This mismatch causes problems later on
(e.g., for the watermark code).  Since we've failed to reconstruct the
BIOS FB, the best solution is to just disable the primary plane and
pretend the BIOS never had it enabled.

v2: Add intel_pre_disable_primary() call (Maarten)

Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449171462-30763-2-git-send-email-matthew.d.roper@intel.com

A long time ago (before 3.14) we relied on a permanent pinning of the
ifbdev to lock the fb in place inside the GGTT. However, the
introduction of stealing the BIOS framebuffer and reusing its address in
the GGTT for the fbdev has muddied waters and we use an inherited fb.
However, the inherited fb is only pinned whilst it is active and we no
longer have an explicit pin for the info->system_base mmapping used by
the fbdev. The result is that after some aperture pressure the fbdev may
be evicted, but we continue to write the fbcon into the same GGTT
address - overwriting anything else that may be put into that offset.
The effect is most pronounced across suspend/resume as
intel_fbdev_set_suspend() does a full clear over the whole scanout.

v2: Only unpin the intel_fb is we allocate it. If we inherit the fb from
the BIOS, we do not own the pinned vma (except for the reference we add
in this patch for our access via info->screen_base).

v3: Finish balancing the vma pinning for the normal !preallocated case.

v4: Try to simplify the pinning even further.
v5: Leak the VMA (cleaned up by object-free) to avoid complicated error paths.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1449245126-26158-1-git-send-email-chris@chris-wilson.co.ukTested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As we mark the preallocated objects as bound, we should also flag them
correctly as being map-and-fenceable (if appropriate!) so that later
users do not get confused and try and rebind the pinned vma in order to
get a map-and-fenceable binding.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1448029000-10616-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I missed this myself when reviewing

commit 237ed86c
Author: Sonika Jindal <sonika.jindal@intel.com>
Date:   Tue Sep 15 09:44:20 2015 +0530

    drm/i915: Check live status before reading edid

Long sleeps like this really shouldn't waste cpu cycles spinning.

Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: "Wang, Gary C" <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449859455-32609-1-git-send-email-daniel.vetter@ffwll.chReviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The device should be on for the whole duration of the update, so check
for this.

v2:
- use the existing dev_priv directly everywhere (Ville)
v3:
- check also that we are in an RPM atomic section (Chris)
- add the assert to i915_ggtt_insert_entries/clear_range too (Chris)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-11-git-send-email-imre.deak@intel.com

In some cases we want to check whether we hold an RPM wakelock reference
for the whole duration of a sequence. To achieve this add a new RPM
atomic sequence counter that we increment any time the wakelock refcount
drops to zero.  Check whether the sequence number stays the same during
the atomic section and that we hold the wakelock at the beginning of the
section.

Motivated by Chris.

v2-v3:
- unchanged
v4:
- swap the order of atomic_read() and assert_rpm_wakelock_held() in
  assert_rpm_atomic_begin() to avoid race
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-10-git-send-email-imre.deak@intel.com

With this change we have the corresponding wake lock checks in both the
rpm get and put functions.

v2-v3:
- unchanged
v4:
- keep the corresponding check in the get helper (Chris)
v5:
- add a note to the commit message that with this change we have the
  checks both in the rpm get and put functions (Joonas)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-9-git-send-email-imre.deak@intel.com

Atm, we assert that the device is not suspended until the point when the
device is truly put to a suspended state. This is fine, but we can catch
more problems if we check that RPM refcount is non-zero. After that one
drops to zero we shouldn't access the device any more, even if the actual
device suspend may be delayed. Change assert_rpm_wakelock_held()
accordingly to check for a non-zero RPM refcount in addition to the
current device-not-suspended check.

For the new asserts to work we need to annotate every place explicitly in
the code where we expect that the device is powered. The places where we
only assume this, but may not hold an RPM reference:
- driver load
  We assume the device to be powered until we enable RPM. Make this
  explicit by taking an RPM reference around the load function.
- system and runtime sudpend/resume handlers
  These handlers are called when the RPM reference becomes 0 and know the
  exact point after which the device can get powered off. Disable the
  RPM-reference-held check for their duration.
- the IRQ, hangcheck and RPS work handlers
  These handlers are flushed in the system/runtime suspend handler
  before the device is powered off, so it's guaranteed that they won't
  run while the device is powered off even though they don't hold any
  RPM reference. Disable the RPM-reference-held check for their duration.

In all these cases we still check that the device is not suspended.
These explicit annotations also have the positive side effect of
documenting our assumptions better.

This caught additional WARNs from the atomic modeset path, those should
be fixed separately.

v2:
- remove the redundant HAS_RUNTIME_PM check (moved to patch 1) (Ville)
v3:
- use a new dedicated RPM wakelock refcount to also catch cases where
  our own RPM get/put functions were not called (Chris)
- assert also that the new RPM wakelock refcount is 0 in the RPM
  suspend handler (Chris)
- change the assert error message to be more meaningful (Chris)
- prevent false assert errors and check that the RPM wakelock is 0 in
  the RPM resume handler too
- prevent false assert errors in the hangcheck work too
- add a device not suspended assert check to the hangcheck work
v4:
- rename disable/enable_rpm_asserts to disable/enable_rpm_wakeref_asserts
  and wakelock_count to wakeref_count
- disable the wakeref asserts in the IRQ handlers and RPS work too
- update/clarify commit message
v5:
- mark places we plan to change to use proper RPM refcounting with
  separate DISABLE/ENABLE_RPM_WAKEREF_ASSERTS aliases (Chris)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450227139-13471-1-git-send-email-imre.deak@intel.com

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-7-git-send-email-imre.deak@intel.com

As a preparation for follow-up patches add a new helper that checks
whether we hold an RPM reference, since this is what we want most of
the cases. Atm this helper will only check for the HW suspended state, a
follow-up patch will do the actual change to check the refcount instead.
One exception is the forcewake release timer function, where it's
guaranteed that the HW is on even though the RPM refcount drops to zero.
This guarantee is provided by flushing the timer in the runtime suspend
handler. So leave the assert_device_not_suspended check in place there.

Also rename assert_device_suspended for consistency and export these
helpers as a preparation for the follow-up patches.

No functional change.

v3:
- change the assert warning message to be more meaningful (Chris)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-6-git-send-email-imre.deak@intel.com

We don't really need to check this flag in the get/put/assert helpers,
as on platforms without RPM support we won't ever enable RPM. That means
pm.suspend will be always false and the assert will be always true.

Do this to simplify the code and to let us extend the RPM asserts to all
platforms for a better coverage.

Motivated by Ville.

v2-v3:
- unchanged
v4:
- remove the HAS_RUNTIME_PM check from intel_runtime_pm_enable() too
  made possible by the previous two patches
v5:
- rebased on the previous new patch in the series that keeps
  HAS_RUNTIME_PM() in intel_runtime_pm_enable() with a permanent
  reference taken there
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450352931-16498-1-git-send-email-imre.deak@intel.com

Currently we disable RPM functionality on platforms that doesn't support
this by not putting/getting the RPM reference we receive from the RPM
core during driver loading/unloading respectively. This is somewhat
obscure, so make it more explicit by keeping a reference dedicated for
this particular purpose whenever the driver is loaded. This makes it
possible to remove the HAS_RUNTIME_PM() special casing from every other
places in the next patch.

v2:
- fix intel_runtime_pm_get vs. intel_runtime_pm_put in
  intel_power_domains_fini()
v3:
- take only a low level RPM reference so the ref tracking asserts
  continue to work (Ville)
- update the commit message
- move the patch earlier for bisectability
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450352696-16135-1-git-send-email-imre.deak@intel.com

We can make the RPM dependency on RC6 explcit in the code by taking an
actual RPM reference, instead of avoiding to drop the initial one. This
will also enable us to remove the HAS_RUNTIME_PM special casing from
more places in the next patch.

v2:
- fixed typo in commit message (Joonas)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-4-git-send-email-imre.deak@intel.com

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-2-git-send-email-imre.deak@intel.com

The RVDA and RVDS (raw VBT data address and size) fields of the ASLE
mailbox may specify an alternate location for VBT instead of mailbox #4.
Use the alternate location if available and valid, falling back to
mailbox #4 otherwise.

v2: Update debug logging (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NMika Kahola <mika.kahola@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178280-28020-1-git-send-email-jani.nikula@intel.com