Also fix a copy and paste error in header of iwl-core.c. This file
is not dual licensed.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes iwlYYY_BROADCAST_ID from run time usage.
hw_setting.sta_bcast_id is used instead.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for reading/writing the SPROM invariants
for PCMCIA based devices.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Only rt2400pci can have the preamble bit set in the PLCP value,
for all other drivers it should not be cleared since that will
conflict with the plcp values for OFDM rates.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Version bump to 2.1.4
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After sampling hundreds of RX frame descriptors,
the results were conclusive:
- The Ralink documentation regarding the SIGNAL and RSSI are wrong.

It turns out that of the 5 BBR registers, we should not use BBR0 and BBR1
for SIGNAL and RSSI respectively, but actually BBR1 and BBR2.
BBR0 does show values, but the exact meaning remains unclear,
but they cannot be translated into a SIGNAL or RSSI field.
BBR3, BBR4 and BBR5 are always 0, so their meaning is unknown.

As it turns out, the reported SIGNAL is the PLCP value, this
in contradiction to what was expected looking at rt2500pci which
only reported the PLCP values for OFDM rates and bitrate values
for CCK rates.

This means we should let the driver raise the flag about the contents
of the SIGNAL field so rt2x00lib can always do the right thing based
on what the driver reports.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to a terrible typo the RX DMA base address
was initialized to the beacon base address.
Obviously bad things happen with bugs like that....
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The basic rate which is configured in the register
should not match all supported rates, but only the _basic_ rates.

Fix this by adding a new flag to the rt2x00_rate structure
and whenever the mode is changed, loop over all available rates
for that band to get the basic rate mask.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whatever mode we are in, according to the legacy drivers
we should always enable TSF ticking/counting.
We should also always enable the TBCN/TBTT field,
this field is only disabled during beacon regeneration.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00dev isn't interested in the rt2x00leds_register() value
anyway. So lets make it return void to even prevent people from
assuming there is anybody interested in the returnvalue.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename config_preamble() to config_erp() and cleanup argument
list by putting it all into a single structure.
This will make the function more meaningful and easier to
expand later. This second option is mostly intended to make
the patch "mac80211: proper short-slot handling" from Johannes Berg
easier to apply for rt2x00.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When mac sets the IEEE80211_TXCTL_SEND_AFTER_DTIM flag, we should
check if the ATIM queue is available in the driver and put the
frame in that queue for proper behavior (send frame after beacon interval).
Unfortunately not all drivers have this ATIM queue, and will lack
this feature for now.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00lib should filter SW diversity out before sending any configuration
changes to the driver. When rt2x00lib fails to do this, it is important
that such events are reported because it _must_ be fixed.
So upgrading the error level to a BUG_ON() which will make sure
this bug gets noticed whenever it happens.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00lib depended on 2 crc algorithms because rt61/rt73
use a different algorithm then rt2800. This means that
even when only 1 algorithm was needed, the dependency was
still present for both.
By moving the checksum generation to the driver we can clean
up 2 annoying flags (which indicated which checksum was required)
and move the dependency to where it belongs: the driver.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The queue->lock could be grabbed from interrupt context,
which could lead to lockdep panic like this:

kernel: ======================================================
kernel: [ INFO: soft-safe -> soft-unsafe lock order detected ]
kernel: 2.6.25-0.95.rc4.fc9 #1
kernel: ------------------------------------------------------
kernel: rt2500pci/1251 [HC0[0]:SC0[1]:HE1:SE0] is trying to acquire:
kernel:  (&queue->lock){--..}, at: [<ffffffff88213339>] rt2x00queue_get_entry+0x5a/0x81 [rt2x00lib]
kernel:
kernel: and this task is already holding:
kernel:  (_xmit_IEEE80211){-...}, at: [<ffffffff8122e9a3>] __qdisc_run+0x84/0x1a9
kernel: which would create a new lock dependency:
kernel:  (_xmit_IEEE80211){-...} -> (&queue->lock){--..}
kernel:
kernel: but this new dependency connects a soft-irq-safe lock:
kernel:  (_xmit_ETHER){-+..}
kernel: ... which became soft-irq-safe at:
kernel:   [<ffffffffffffffff>] 0xffffffffffffffff
kernel:
kernel: to a soft-irq-unsafe lock:
kernel:  (&queue->lock){--..}
kernel: ... which became soft-irq-unsafe at:
kernel: ...  [<ffffffff810545a2>] __lock_acquire+0x62d/0xd63
kernel:   [<ffffffff81054d36>] lock_acquire+0x5e/0x78
kernel:   [<ffffffff812a1497>] _spin_lock+0x26/0x53
kernel:   [<ffffffff88212f98>] rt2x00queue_reset+0x16/0x40 [rt2x00lib]
kernel:   [<ffffffff88212fd4>] rt2x00queue_alloc_entries+0x12/0xab [rt2x00lib]
kernel:   [<ffffffff88213091>] rt2x00queue_initialize+0x24/0xf2 [rt2x00lib]
kernel:   [<ffffffff88212036>] rt2x00lib_start+0x3b/0xd4 [rt2x00lib]
kernel:   [<ffffffff88212609>] rt2x00mac_start+0x18/0x1a [rt2x00lib]
kernel:   [<ffffffff881b9a4b>] ieee80211_open+0x1f3/0x46d [mac80211]
kernel:   [<ffffffff8121d980>] dev_open+0x4d/0x8b
kernel:   [<ffffffff8121d41e>] dev_change_flags+0xaf/0x172
kernel:   [<ffffffff81224fc2>] do_setlink+0x276/0x338
kernel:   [<ffffffff81225198>] rtnl_setlink+0x114/0x116
kernel:   [<ffffffff812262fc>] rtnetlink_rcv_msg+0x1d8/0x1f9
kernel:   [<ffffffff8123649a>] netlink_rcv_skb+0x3e/0xac
kernel:   [<ffffffff8122611a>] rtnetlink_rcv+0x29/0x33
kernel:   [<ffffffff81235eed>] netlink_unicast+0x1fe/0x26b
kernel:   [<ffffffff81236224>] netlink_sendmsg+0x2ca/0x2dd
kernel:   [<ffffffff812103b3>] sock_sendmsg+0xfd/0x120
kernel:   [<ffffffff812105a8>] sys_sendmsg+0x1d2/0x23c
kernel:   [<ffffffff8100c1c7>] tracesys+0xdc/0xe1
kernel:   [<ffffffffffffffff>] 0xffffffffffffffff

This can be fixed by using the irqsave/irqrestore versions
during the queue->lock handling.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix trivial log message.
Signed-off-by: NLuis Correia <luis.f.correia@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When fixing up the packet alignment, if we had to add 2 bytes to the front of
the skb we need to remember to take them off the end afterwards. This fixes
reception of encrypted packets which were otherwise failing with an invalid
ICV.
Signed-off-by: NAdam Baker <linux@baker-net.org.uk>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should not write 0 to the beacon sync register during
config_intf() since that will clear out the beacon interval
and forces the beacon to be send out at the lowest interval.
(reported by Mattias Nissler).

The side effect of the same bug was that while working with
multiple virtual AP interfaces a change for any of those
interfaces would disable beaconing untill an beacon update
was provided.

This is resolved by only updating the TSF_SYNC value during
config_intf(). In update_beacon() we disable beaconing
temporarily to prevent fake beacons to be transmitted.
Finally kick_tx_queue() will enable beaconing again.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In rt2x00lib_write_tx_desc() the skb->data and skb->len fields
were incorrectly used. For USB drivers both of those values
contain invalid data (skb->data points to the device descriptor,
skb->len contains the frame _and_ descriptor length).

Instead of using the skbuffer fields we should use the skbdesc
fields which are correctly initialized and contain all the data
that we need.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rxdesc->size is unitialized before the desriptor has been read.
Move the truncation of the sk buffer to the moment all variables
have been initialized.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

skbdesc->desc_len is uninitialized at the start
of the function. So it is a _bad_ idea to use it...
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sizeof() operator was incorrectly applied to the pointer, not the struct.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the TX path, the driver didn't copy the TX control data structure. Thus, it
was invalid in the TX done handler, causing serious trouble and misbehaviour.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some architectures give problems when reading
RX frame descriptor words when the descriptor
is not aligned on a 4 byte boundrary.

Due to optimalizations for the ieee80211 payload
4 byte alignment, it is no longer guarenteed
that the descriptor is placed on the 4 byte
boundrary (In fact, for rt73usb it is absolutely
never aligned to 4 bytes, for rt2500usb it depends
on the length of the payload).

This will copy the descriptor to a 4 byte aligned
location before it is read for the first time.
This will also move the payload data alignment
in rt2x00usb (instead of inside the driver) where
it has always belonged.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename members of ndis_80211_* structures to match the style of
the rest of the code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename enums and structures to ndis_80211_* for greater readability.
Also change order so that enumerations are presented first.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

(test == true) is not nice.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After my bit scan re-writing the SIOCSIWSCAN wext ioctl no longer supported
scanning for a specific SSID. However, wpa_supplicant is a possible user of
this ioctl, so here is code that add's this.

While passing, removed even more of the debugfs-based scanning. You can (and
should) the SIOCSIWSCAN to ask for scans, so there is no need for
proprietary interfaces for scanning. And, besides, the scan result couldn't
be used further, e.g. not for associating.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: <Larry.Finger@lwfinger.net>
Cc: <stefano.brivio@polimi.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

b43_mac_{enable,suspend}() can now become static.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a change to a previous patch ("iwlwifi: 3945 split tx_complete
to command and packet function") to ensure we do not have hardirq safe
locks (priv->lock in this case) depend on hardirq unsafe locks.

We only call iwl3945_tx_queue_reclaim while in a tasklet so we have to use
the irqsafe version of the function.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath5k/debug.c: In function 'read_file_tsf': drivers/net/wireless/ath5k/debug.c:203: warning: format '%016llx'
expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/ath5k/debug.c:203: warning: format '%016llx'
expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/ath5k/debug.c: In function 'read_file_beacon':
drivers/net/wireless/ath5k/debug.c:274: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/ath5k/debug.c:274: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'u64'

drivers/net/wireless/iwlwifi/iwl-4965.c: In function 'iwl4965_tx_status_reply_compressed_ba':
drivers/net/wireless/iwlwifi/iwl-4965.c:3907: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/iwlwifi/iwl-4965.c: In function 'iwl4965_rx_reply_compressed_ba':
drivers/net/wireless/iwlwifi/iwl-4965.c:4039: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type '__le64'
drivers/net/wireless/iwlwifi/iwl-4965.c:4046: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
drivers/net/wireless/iwlwifi/iwl4965-base.c: In function 'iwl4965_tx_status_reply_tx':
drivers/net/wireless/iwlwifi/iwl4965-base.c:3661: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

atheros hardware has a problem with the rx timestamp of some IBSS beacons when
they caused a TSF update (they have the same BSSID).

the rx timestamp is wrong especially if the beacon frames get bigger than 78
byte (at least on AR5213 and AR5414 hardware). in that case ath5k_extend_tsf()
will assume a rs_tstamp overflow and give us a timestamp too far in the past
which will cause mac80211 to merge IBSS on every beacon (which is not necessary
since the BSSID already matches). but in this case we know that the HW must
have synced to the beacons TSF and the rx timestamp must be later than that so
we can adjust mactime accordingly.

also rename the function to ath5k_check_ibss_tsf() and change comments, since
"hw merge" is better described as a TSF update.

drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NBruno Randolf <bruno@thinktube.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

add comments about the fact that we don't know when exactly the atheros
hardware takes the RX timestamp.

drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NBruno Randolf <bruno@thinktube.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

move ath5k_tx_status and ath5k_rx_status structures out of the hardware
descriptor since they are not accessed by the hardware at all. they just
contain converted information from the hardware descriptor. since they are only
used in the rx and tx tasklets there is also no use to keep them for each
descriptor.

drivers/net/wireless/ath5k/ath5k.h:     Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/debug.c:     Changes-licensed-under: GPL
drivers/net/wireless/ath5k/debug.h:     Changes-licensed-under: GPL
drivers/net/wireless/ath5k/hw.c:        Changes-licensed-under: ISC
Signed-off-by: NBruno Randolf <bruno@thinktube.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>