- 29 6月, 2015 10 次提交
-
-
由 Mugunthan V N 提交于
When limiting phy link speed using "max-speed" to 100mbps or less on a giga bit phy, phy never completes auto negotiation and phy state machine is held in PHY_AN. Fixing this issue by comparing the giga bit advertise though phydev->supported doesn't have it but phy has BMSR_ESTATEN set. So that auto negotiation is restarted as old and new advertise are different and link comes up fine. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gilad Ben-Yossef 提交于
DSA master netdev promiscuity counter was not being properly decremented on slave device open error path. Signed-off-by: NGilad Ben-Yossef <gilad@benyossef.com> CC: Gilad Ben-Yossef <giladb@ezchip.com> CC: David S. Miller <davem@davemloft.net> CC: Florian Fainelli <f.fainelli@gmail.com> CC: Guenter Roeck <linux@roeck-us.net> CC: Andrew Lunn <andrew@lunn.ch> CC: Scott Feldman <sfeldma@gmail.com> Acked-by: NAndrew Lunn <andrew@lunn.ch> Acked-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
David Miller says: ==================== Get rid of sock->sk_protinfo. These two patches get rid of the last remaining user of sk_protinfo (ax25) and then really gets rid of the struct member. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Miller 提交于
No more users, so it can now be removed. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Miller 提交于
Just make a ax25_sock structure that provides the ax25_cb pointer. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Geert Uytterhoeven 提交于
If CONFIG_ACPI=n: drivers/net/ethernet/apm/xgene/xgene_enet_main.c: In function ‘xgene_enet_get_resources’: drivers/net/ethernet/apm/xgene/xgene_enet_main.c:951: warning: ‘ret’ may be used uninitialized in this function If the driver is bound to a legacy platform device, ret will contain arbitrary data. If it is non-zero, it will be returned to the caller as an error code. Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Geert Uytterhoeven 提交于
net/core/flow_dissector.c: In function ‘__skb_flow_dissect’: net/core/flow_dissector.c:132: warning: ‘ip_proto’ may be used uninitialized in this function Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org> Acked-by: NTom Herbert <tom@herbertland.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Li, Liang Z 提交于
The function netif_set_real_num_tx_queues() will return -EINVAL if the second parameter < 1, so call this function with the second parameter set to 0 is meaningless. Signed-off-by: NLiang Li <liang.z.li@intel.com> Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andy Gospodarek 提交于
The following lockdep splat was seen due to the wrong context for grabbing in_dev. =============================== [ INFO: suspicious RCU usage. ] 4.1.0-next-20150626-dbg-00020-g54a6d91-dirty #244 Not tainted ------------------------------- include/linux/inetdevice.h:205 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 1, debug_locks = 0 2 locks held by ip/403: #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff81453305>] rtnl_lock+0x17/0x19 #1: ((inetaddr_chain).rwsem){.+.+.+}, at: [<ffffffff8105c327>] __blocking_notifier_call_chain+0x35/0x6a stack backtrace: CPU: 2 PID: 403 Comm: ip Not tainted 4.1.0-next-20150626-dbg-00020-g54a6d91-dirty #244 0000000000000001 ffff8800b189b728 ffffffff8150a542 ffffffff8107a8b3 ffff880037bbea40 ffff8800b189b758 ffffffff8107cb74 ffff8800379dbd00 ffff8800bec85800 ffff8800bf9e13c0 00000000000000ff ffff8800b189b7d8 Call Trace: [<ffffffff8150a542>] dump_stack+0x4c/0x6e [<ffffffff8107a8b3>] ? up+0x39/0x3e [<ffffffff8107cb74>] lockdep_rcu_suspicious+0xf7/0x100 [<ffffffff814b63c3>] fib_dump_info+0x227/0x3e2 [<ffffffff814b6624>] rtmsg_fib+0xa6/0x116 [<ffffffff814b978f>] fib_table_insert+0x316/0x355 [<ffffffff814b362e>] fib_magic+0xb7/0xc7 [<ffffffff814b4803>] fib_add_ifaddr+0xb1/0x13b [<ffffffff814b4d09>] fib_inetaddr_event+0x36/0x90 [<ffffffff8105c086>] notifier_call_chain+0x4c/0x71 [<ffffffff8105c340>] __blocking_notifier_call_chain+0x4e/0x6a [<ffffffff8105c370>] blocking_notifier_call_chain+0x14/0x16 [<ffffffff814a7f50>] __inet_insert_ifa+0x1a5/0x1b3 [<ffffffff814a894d>] inet_rtm_newaddr+0x350/0x35f [<ffffffff81457866>] rtnetlink_rcv_msg+0x17b/0x18a [<ffffffff8107e7c3>] ? trace_hardirqs_on+0xd/0xf [<ffffffff8146965f>] ? netlink_deliver_tap+0x1cb/0x1f7 [<ffffffff814576eb>] ? rtnl_newlink+0x72a/0x72a ... This patch resolves that splat. Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com> Reported-by: NSergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jon Paul Maloy 提交于
In commit 1f66d161 ("tipc: introduce starvation free send algorithm") we introduced a counter per priority level for buffers in the link backlog queue. We also introduced a new function tipc_link_purge_backlog(), to reset these counters to zero when the link is reset. Unfortunately, we missed to call this function when the broadcast link is reset, with the result that the values of these counters might be permanently skewed when new nodes are attached. This may in the worst case lead to permananent, but spurious, broadcast link congestion, where no broadcast packets can be sent at all. We fix this bug with this commit. Signed-off-by: NJon Maloy <jon.maloy@ericsson.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 6月, 2015 30 次提交
-
-
由 David S. Miller 提交于
Yuval Mintz says: ==================== bnx2x: various fixes This patch series contains several small fixes [with the possible exception of the first 2 link fixes] for various driver flows. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Due to FW constraints, driver must make sure that transmitted SKBs will not be too fragmented, or in the case that they are - that each 'window' of fragments passed to the FW would contain at least an mss worth of data. For encapsultaed packets the calculation is wrong, since it ignores the inner headers in the calculation of the headers' length. This could lead to a FW assertion in case of a too-fragmented encapsulated packet. Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
During an error flow when trying to access the nvram the driver doesn't release the hw lock it acquired. Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ariel Elior 提交于
Since driver statistics flow access MACs and those might reset during link re-configurations, when we're about to change link properties we have to make sure that statistics are not operational. Statisics would be re-enabled [i.e., gathering of statistics would re-commence] once physical link is achieved again. Since driver employs a link-flap avoidance scheme, there are scenarios where driver will receive no indication that the new link is up, and as a result the statistics would not be re-enabled. Preventing LFA from working in such cases would guarantee that we'll always receive such indications and thus will fix statistics gathering. Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com> Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
20g-capable devices are not configured properly for self-test, using 10g as their speed which cause the link indication to remain down and fail the internal loopback test. Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shahed Shaikh 提交于
There's a bug in today's driver where VF requests to add/remove MAC filters always reach the Hypervisor as add requests. This prevents the VF from changing its MAC address, as it cannot remove the previously configured MAC and runs out of MAC credits. Signed-off-by: NShahed Shaikh <Shahed.Shaikh@qlogic.com> Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Manish Chopra 提交于
The scratchpad is a shared block between all functions of a given device. Due to HW limitations, we can't properly close its parity notifications to all functions on legal flows. E.g., it's possible that while taking a register dump from one function a parity error would be triggered on other functions. Today driver doesn't consider this parity as a 'real' parity unless its being accompanied by additional indications [which would happen in a real parity scenario]; But it does print notifications for such events in the system logs. This eliminates such prints - in case of real parities driver would have additional indications; But if this is the only signal user will not even see a parity being logged in the system. Signed-off-by: NManish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Each time a flow finishes reads from the classification shadow configuration in the driver, that flow would check for pending commands and pass them to FW if possible. In case there's already a completion pending command, I.e., a ramrod that has been sent to the FW and is yet to be completed while said flow tries to configure the pending command we would get a false error message in logs [and panic if SOE was used for driver compilation] since the command could not have been completed. This prevents said print [and panic]; The pending command will be sent by the time the completion of the current sent command would arrive. Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
ethtool shows KR supported/advertised speeds incorrectly as baseT in cases the board is in fact KR-base. Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com> Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
This fixes several issues relating to asymmetric configuration: 1. When user requests to disable TX, the local-device needs to advertise both PAUSE and ASM_DIR, but to avoid transmitting pause frames. In the 578xx, it would ignore the TX disable. 2. When user advertises RX-only, ASM_DIR was advertised instead of PAUSE/ASM_DIR. 3. When changing mode, the advertised PAUSE/ASM_DIR was not cleared before setting new one, so disabling RX or TX had no impact on the 'advertised' as appeared in the 'ethtool -a' output. Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com> Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jamal Hadi Salim 提交于
Fix typo in the validation rules for flower's attributes Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
We use spinlock to access a single flag. We can avoid spin_locks by using atomic variable and atomic_cmpxchg(). Use atomic_cmpxchg to set the flag for idle to poll. And a simple atomic_set to unlock (set idle from poll). In napi poll, if gro is enabled, we call napi_gro_receive() to deliver the packets. Before we call napi_complete(), i.e while re-polling, if low latency busy poll is called, we use netif_receive_skb() to deliver the packets. At this point if there are some skb's held in GRO, busy poll could deliver the packets out of order. So we call napi_gro_flush() to flush skbs before we move the napi poll to idle. Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shaohui Xie 提交于
Vitesse VSC8641 is compatible with Vitesse 82xx Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alison Wang 提交于
CONFIG_GIANFAR is not depended on FSL_SOC, it can be built on non-PPC platforms. Signed-off-by: NAlison Wang <alison.wang@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dan Carpenter 提交于
There was a missing assignment so the "if (ret)" on the next line is never true. Fixes: f21fb3ed ('Add support of Cavium Liquidio ethernet adapters') Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dan Carpenter 提交于
We need to unlock before returning here. Fixes: a0d2f206 ('Renesas Ethernet AVB PTP clock driver') Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Or Gerlitz says: ==================== mlx4 driver fixes, June 24, 2015 Some fixes that we made recently, all need to go into stable. patch #1 "net/mlx4_en: Release TX QP when destroying TX ring" and patch #3 "Fix wrong csum complete report when rxvlan offload is disabled" to >= 3.19 patch #2 "Wake TX queues only when there's enough room" addressing a bug which is there from day one... should go to whatever kernels it's still applicable patch #4 "mlx4: Disable HA for SRIOV PF RoCE devices" to >= 4.0 The patches are marked with net but are made against net-next, as the net tree still doesn't contain all the net-next bits. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Or Gerlitz 提交于
When in HA mode, the driver exposes an IB (RoCE) device instance with only one port. Under SRIOV, the existing implementation doesn't go well with the PF RoCE driver's role of Special QPs Para-Virtualization, etc. As such, disable HA for the mlx4 PF RoCE device in SRIOV mode. Fixes: a5750090 ('IB/mlx4: Add port aggregation support') Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Shamay 提交于
The check_csum() function relied on hwtstamp_rx_filter to know if rxvlan offload is disabled. This is wrong since rxvlan offload can be switched on/off regardless of hwtstamp_rx_filter. Also moved check_csum to query CQE information to identify VLAN packets and removed the check of IP packets, since it has been validated before. Fixes: f8c6455b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE') Signed-off-by: NIdo Shamay <idos@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ido Shamay 提交于
Indication of a single completed packet, marked by txbbs_skipped being bigger then zero, in not enough in order to wake up a stopped TX queue. The completed packet may contain a single TXBB, while next packet to be sent (after the wake up) may have multiple TXBBs (LSO/TSO packets for example), causing overflow in queue followed by WQE corruption and TX queue timeout. Instead, wake the stopped queue only when there's enough room for the worst case (maximum sized WQE) packet that we should need to handle after the queue is opened again. Also created an helper routine - mlx4_en_is_tx_ring_full, which checks if the current TX ring is full or not. It provides better code readability and removes code duplication. Signed-off-by: NIdo Shamay <idos@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eran Ben Elisha 提交于
TX ring QP wasn't released at mlx4_en_destroy_tx_ring. Instead, the code used the deprecated base_tx_qpn field. Move TX QP release to mlx4_en_destroy_tx_ring and remove the base_tx_qpn field. Fixes: ddae0349 ('net/mlx4: Change QP allocation scheme') Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Linus Torvalds 提交于
Merge first patchbomb from Andrew Morton: - a few misc things - ocfs2 udpates - kernel/watchdog.c feature work (took ages to get right) - most of MM. A few tricky bits are held up and probably won't make 4.2. * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (91 commits) mm: kmemleak_alloc_percpu() should follow the gfp from per_alloc() mm, thp: respect MPOL_PREFERRED policy with non-local node tmpfs: truncate prealloc blocks past i_size mm/memory hotplug: print the last vmemmap region at the end of hot add memory mm/mmap.c: optimization of do_mmap_pgoff function mm: kmemleak: optimise kmemleak_lock acquiring during kmemleak_scan mm: kmemleak: avoid deadlock on the kmemleak object insertion error path mm: kmemleak: do not acquire scan_mutex in kmemleak_do_cleanup() mm: kmemleak: fix delete_object_*() race when called on the same memory block mm: kmemleak: allow safe memory scanning during kmemleak disabling memcg: convert mem_cgroup->under_oom from atomic_t to int memcg: remove unused mem_cgroup->oom_wakeups frontswap: allow multiple backends x86, mirror: x86 enabling - find mirrored memory ranges mm/memblock: allocate boot time data structures from mirrored memory mm/memblock: add extra "flags" to memblock to allow selection of memory based on attribute mm: do not ignore mapping_gfp_mask in page cache allocation paths mm/cma.c: fix typos in comments mm/oom_kill.c: print points as unsigned int mm/hugetlb: handle races in alloc_huge_page and hugetlb_reserve_pages ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux由 Linus Torvalds 提交于
Pull pstore updates from Tony Luck: "Miscellaneous pstore improvements" * tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: ramoops: make it possible to change mem_type param. pstore/ram: verify ramoops header before saving record fs/pstore: Optimization function ramoops_init_przs fs/pstore: update the backend parameter in pstore module pstore: do not use message compression without lock
-
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs由 Linus Torvalds 提交于
Pull f2fs updates from Jaegeuk Kim: "New features: - per-file encryption (e.g., ext4) - FALLOC_FL_ZERO_RANGE - FALLOC_FL_COLLAPSE_RANGE - RENAME_WHITEOUT Major enhancement/fixes: - recovery broken superblocks - enhance f2fs_trim_fs with a discard_map - fix a race condition on dentry block allocation - fix a deadlock during summary operation - fix a missing fiemap result .. and many minor bug fixes and clean-ups were done" * tag 'for-f2fs-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (83 commits) f2fs: do not trim preallocated blocks when truncating after i_size f2fs crypto: add alloc_bounce_page f2fs crypto: fix to handle errors likewise ext4 f2fs: drop the volatile_write flag only f2fs: skip committing valid superblock f2fs: setting discard option in parse_options() f2fs: fix to return exact trimmed size f2fs: support FALLOC_FL_INSERT_RANGE f2fs: hide common code in f2fs_replace_block f2fs: disable the discard option when device doesn't support f2fs crypto: remove alloc_page for bounce_page f2fs: fix a deadlock for summary page lock vs. sentry_lock f2fs crypto: clean up error handling in f2fs_fname_setup_filename f2fs crypto: avoid f2fs_inherit_context for symlink f2fs crypto: do not set encryption policy for non-directory by ioctl f2fs crypto: allow setting encryption policy once f2fs crypto: check context consistent for rename2 f2fs: avoid duplicated code by reusing f2fs_read_end_io f2fs crypto: use per-inode tfm structure f2fs: recovering broken superblock during mount ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs由 Linus Torvalds 提交于
Pull UDF fixes and cleanups from Jan Kara: "The contains some small fixes and improvements in error handling for UDF. Bundled is also one ext3 coding style fix and a fix in quota documentation" * 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: udf: fix udf_load_pvoldesc() udf: remove double err declaration in udf_file_write_iter() UDF: support NFSv2 export fs: ext3: super: fixed a space coding style issue quota: Update documentation udf: Return error from udf_find_entry() udf: Make udf_get_filename() return error instead of 0 length file name udf: bug on exotic flag in udf_get_filename() udf: improve error management in udf_CS0toNLS() udf: improve error management in udf_CS0toUTF8() udf: unicode: update function name in comments udf: remove unnecessary test in udf_build_ustr_exact() udf: Return -ENOMEM when allocation fails in udf_get_filename()
-
git://git.lwn.net/linux-2.6由 Linus Torvalds 提交于
Pull documentation updates from Jonathan Corbet: "The main thing here is Ingo's big subdirectory documenting feature support for each architecture. Beyond that, it's the usual pile of fixes, tweaks, and small additions" * tag 'docs-for-linus' of git://git.lwn.net/linux-2.6: (79 commits) doc:md: fix typo in md.txt. Documentation/mic/mpssd: don't build x86 userspace when cross compiling Documentation/prctl: don't build tsc tests when cross compiling Documentation/vDSO: don't build tests when cross compiling Doc:ABI/testing: Fix typo in sysfs-bus-fcoe Doc: Docbook: Change wikipedia's URL from http to https in scsi.tmpl Doc: Change wikipedia's URL from http to https Documentation/kernel-parameters: add missing pciserial to the earlyprintk Doc:pps: Fix typo in pps.txt kbuild : Fix documentation of INSTALL_HDR_PATH Documentation: filesystems: updated struct file_operations documentation in vfs.txt kbuild: edit explanation of clean-files variable Doc: ja_JP: Fix typo in HOWTO Move freefall program from Documentation/ to tools/ Documentation: ARM: EXYNOS: Describe boot loaders interface Doc:nfc: Fix typo in nfc-hci.txt vfs: Minor documentation fix Doc: networking: txtimestamp: fix printf format warning Documentation, intel_pstate: Improve legacy mode internal governors description Documentation: extend use case for EXPORT_SYMBOL_GPL() ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input由 Linus Torvalds 提交于
Pull input subsystem updates from Dmitry Torokhov: "Thanks to Samuel Thibault input device (keyboard) LEDs are no longer hardwired within the input core but use LED subsystem and so allow use of different triggers; Hans de Goede did a large update for the ALPS touchpad driver; we have new TI drv2665 haptics driver and DA9063 OnKey driver, and host of other drivers got various fixes" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits) Input: pixcir_i2c_ts - fix receive error MAINTAINERS: remove non existent input mt git tree Input: improve usage of gpiod API tty/vt/keyboard: define LED triggers for VT keyboard lock states tty/vt/keyboard: define LED triggers for VT LED states Input: export LEDs as class devices in sysfs Input: cyttsp4 - use swap() in cyttsp4_get_touch() Input: goodix - do not explicitly set evbits in input device Input: goodix - export id and version read from device Input: goodix - fix variable length array warning Input: goodix - fix alignment issues Input: add OnKey driver for DA9063 MFD part Input: elan_i2c - add product IDs FW names Input: elan_i2c - add support for multi IC type and iap format Input: focaltech - report finger width to userspace tty: remove platform_sysrq_reset_seq Input: synaptics_i2c - use proper boolean values Input: psmouse - use true instead of 1 for boolean values Input: cyapa - fix a few typos in comments Input: stmpe-ts - enforce device tree only mode ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp由 Linus Torvalds 提交于
Pull EDAC updates from Borislav Petkov: - New APM X-Gene SoC EDAC driver (Loc Ho) - AMD error injection module improvements (Aravind Gopalakrishnan) - Altera Arria 10 support (Thor Thayer) - misc fixes and cleanups all over the place * tag 'edac_for_4.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (28 commits) EDAC: Update Documentation/edac.txt EDAC: Fix typos in Documentation/edac.txt EDAC, mce_amd_inj: Set MISCV on injection EDAC, mce_amd_inj: Move bit preparations before the injection EDAC, mce_amd_inj: Cleanup and simplify README EDAC, altera: Do not allow suspend when EDAC is enabled EDAC, mce_amd_inj: Make inj_type static arm: socfpga: dts: Add Arria10 SDRAM EDAC DTS support EDAC, altera: Add Arria10 EDAC support EDAC, altera: Refactor for Altera CycloneV SoC EDAC, altera: Generalize driver to use DT Memory size EDAC, mce_amd_inj: Add README file EDAC, mce_amd_inj: Add individual permissions field to dfs_node EDAC, mce_amd_inj: Modify flags attribute to use string arguments EDAC, mce_amd_inj: Read out number of MCE banks from the hardware EDAC, mce_amd_inj: Use MCE_INJECT_GET macro for bank node too EDAC, xgene: Fix cpuid abuse EDAC, mpc85xx: Extend error address to 64 bit EDAC, mpc8xxx: Adapt for FSL SoC EDAC, edac_stub: Drop arch-specific include ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl由 Linus Torvalds 提交于
Pull pin control updates from Linus Walleij: "Here is the bulk of pin control changes for the v4.2 series: Quite a lot of new SoC subdrivers and two new main drivers this time, apart from that business as usual. Details: Core functionality: - Enable exclusive pin ownership: it is possible to flag a pin controller so that GPIO and other functions cannot use a single pin simultaneously. New drivers: - NXP LPC18xx System Control Unit pin controller - Imagination Pistachio SoC pin controller New subdrivers: - Freescale i.MX7d SoC - Intel Sunrisepoint-H PCH - Renesas PFC R8A7793 - Renesas PFC R8A7794 - Mediatek MT6397, MT8127 - SiRF Atlas 7 - Allwinner A33 - Qualcomm MSM8660 - Marvell Armada 395 - Rockchip RK3368 Cleanups: - A big cleanup of the Marvell MVEBU driver rectifying it to correspond to reality - Drop platform device probing from the SH PFC driver, we are now a DT only shop for SuperH - Drop obsolte multi-platform check for SH PFC - Various janitorial: constification, grammar etc Improvements: - The AT91 GPIO portions now supports the set_multiple() feature - Split out SPI pins on the Xilinx Zynq - Support DTs without specific function nodes in the i.MX driver" * tag 'pinctrl-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits) pinctrl: rockchip: add support for the rk3368 pinctrl: rockchip: generalize perpin driver-strength setting pinctrl: sh-pfc: r8a7794: add SDHI pin groups pinctrl: sh-pfc: r8a7794: add MMCIF pin groups pinctrl: sh-pfc: add R8A7794 PFC support pinctrl: make pinctrl_register() return proper error code pinctrl: mvebu: armada-39x: add support for Armada 395 variant pinctrl: mvebu: armada-39x: add missing SATA functions pinctrl: mvebu: armada-39x: add missing PCIe functions pinctrl: mvebu: armada-38x: add ptp functions pinctrl: mvebu: armada-38x: add ua1 functions pinctrl: mvebu: armada-38x: add nand functions pinctrl: mvebu: armada-38x: add sata functions pinctrl: mvebu: armada-xp: add dram functions pinctrl: mvebu: armada-xp: add nand rb function pinctrl: mvebu: armada-xp: add spi1 function pinctrl: mvebu: armada-39x: normalize ref clock naming pinctrl: mvebu: armada-xp: rename spi to spi0 pinctrl: mvebu: armada-370: align spi1 clock pin naming pinctrl: mvebu: armada-370: align VDD cpu-pd pin naming with datasheet ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight由 Linus Torvalds 提交于
Pull backlight updates from Lee Jones: "Changes to existing drivers: - supply MODULE_DEVICE_TABLE() to ensure probing - constify struct; da9052_bl - enable compile test; lcd_l4f00242t03, lcd_lms283fg05, backlight_gpio - suspend/resume bugfix; lp855x_bl - devm_gpiod_get_optional() API fixup; pwm_bl - error handling fixup; backlight" * tag 'backlight-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: backlight: Change the return type of backlight_update_status() to int backlight: pwm_bl: Simplify usage of devm_gpiod_get_optional backlight: lp855x: Don't clear level on suspend/blank backlight: Allow compile test of GPIO consumers if !GPIOLIB video: backlight: da9052: Constify platform_device_id gpio-backlight: Discover driver during boot time
-