This is patch 4 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.

This patch contains following changes:
 - limits the watchdog timeout to 1-63 while this
   device accepts 1-255.
Signed-off-by: NSamuel Tardieu <sam@rfc1149.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This is patch 3 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.

This patch contains following changes:
 - Fix identation.
Signed-off-by: NSamuel Tardieu <sam@rfc1149.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This is patch 2 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.

This patch contains following changes:
 - wdt_io is 2 bytes long. We should do a
   request_region for 2 bytes instead of 1.
Signed-off-by: NSamuel Tardieu <sam@rfc1149.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This is patch 1 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.

This patch contains following changes:
 - the note concerning tyan motherboards has been copied from
   another driver, This doesn't apply here.
 - the comments concerning CRF6 are wrong as CRF3 is manipulated
   and CRF6 is never read nor written.
 - the comments concerning CRF5 are wrong as CRF4 is manipulated
   and CRF5 is never read nor written.
Signed-off-by: NSamuel Tardieu <sam@rfc1149.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Return ENOTTY instead of ENOIOCTLCMD in user-visible ioctl() results

The watchdog drivers used to return ENOIOCTLCMD for bad ioctl() commands.
ENOIOCTLCMD should not be visible by the user, so use ENOTTY instead.
Signed-off-by: NSamuel Tardieu <sam@rfc1149.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

fixed some more trailing spaces.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Add io spinlocks to prevent possible race
conditions between start and stop operations
that are issued from different child processes
where the master process opened /dev/watchdog.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

* fix typo's according to spellings checker
* Fix some leading and trailing spaces
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

New watchdog driver for the Winbond W83697HF chipset.
Signed-off-by: NMarcus Junker <junker@anduras.de>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

* Added io spinlocking
* Deleted WATCHDOG_MINOR (it's in the miscdevice include
* Changed timer_enabled to use set_bit functions
* WDIOC_GETSUPPORT should return -EFAULT or 0
* timeout should be correct before we initialize the watchdog
* we should initialize the watchdog before we give access
  to userspace
* Third parameter of module_param is not the default or
  initial value
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Remove trailing whitespace.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

New watchdog driver for the Winbond SMsC37B787 chipset.
Signed-off-by: NSven Anders <anders@anduras.de>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Retry internal operation after unit check instead of aborting them.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add timeout handler for common-I/O-layer-internal I/O operations.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use page_to_phys and pfn_to_page to avoid open-coded mem_map usage.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Size zones and holes in an architecture independent manner for s390.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

The include of linux/smp.h needs to be done before the #if that
checks for the compiler version. Seems like fallout from the
inline assembly cleanup patch vs. the directed yield patch.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Fix a race condition during AP device registration and unregistration.
Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

While the machine owns us an interrupt in these cases (and we should get
one), reality isn't always like that...
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Fix new restore_sigregs function. It copies the user space copy of the
old psw without correcting the psw.mask and the psw.addr high order bit.
While we are at it, simplify save_sigregs a bit.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

* 'for-2.6.19' of git://brick.kernel.dk/data/git/linux-2.6-block:
  [PATCH] Document bi_sector and sector_t
  [PATCH] helper function for retrieving scsi_cmd given host based block layer tag

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Remove remaining reference to ite_gpio.h from Kbuild
  [MIPS] PNX8550 fixups

Signed-Off-By: NRoger Gammans <rgammans@computer-surgery.co.uk>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This was necessitated by the need for a function to get back
to a scsi_cmnd, when an hba the posts its (corresponding) completion
interrupt with a block layer tag as its reference.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NDavid Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (4712): Fix warning when compiling on x86_i64
  V4L/DVB (4711): Radio: No need to return void
  V4L/DVB (4708): Add tveeprom support for Philips FM1236/FM1216ME MK5
  V4L/DVB (4707): 4linux: complete conversion to hotplug safe PCI API
  V4L/DVB (4706): Do not enable VIDEO_V4L2 unconditionally
  V4L/DVB (4704): SAA713x: fixed compile warning in SECAM fixup
  V4L/DVB (4703): Add support for the ASUS EUROPA2 OEM board
  V4L/DVB (4702): Fix: set antenna input for DVB-T for Asus P7131 Dual hybrid
  V4L/DVB (4701): Saa713x audio fixes
  V4L/DVB (4676a): Remove Kconfig item for DiB7000M support

The atmel_console_get_options() function initializes the baud,
parity and bits settings from the actual hardware setup, in
case it has been initialized by a e.g. boot loader.

The baud rate, however, is not necessarily exactly equal to one of
the standard baud rates (115200, etc.) This means that the baud rate
calculated by this function may be slightly higher or slightly lower
than one of the standard baud rates.

If the baud rate is slightly lower than the target, this causes
problems when uart_set_option() tries to match the detected baud rate
against the standard baud rate, as it will always select a baud rate
that is lower or equal to the target rate. For example if the
detected baud rate is slightly lower than 115200, usart_set_options()
will select 57600.

This patch fixes the problem by subtracting 1 from the value in BRGR
when calculating the baud rate. The detected baud rate will thus
always be higher than the nearest standard baud rate, and
uart_set_options() will end up doing the right thing.

Tested on ATSTK1000 and AT91RM9200-EK boards. Both are broken without
this patch.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Allow the board to remap actual USART peripheral devices to serial
devices by calling at32_map_usart(hw_id, serial_line). This ensures
that even though ATSTK1002 uses USART1 as the first serial port, it
will still have a ttyS0 device.

This also adds a board-specific early setup hook and moves the
at32_setup_serial_console() call there from the platform code.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make CONFIG_SERIAL_ATMEL selectable on AVR32 and #ifdef out some ARM-
specific code in the driver.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.

This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.

On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.

If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Rename at91_register_uart_fns and associated structs and variables
to make it consistent with the atmel_ prefix used by the rest of
the driver.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The at91_serial driver can be used with both AT32 and AT91 devices
from Atmel and has therefore been renamed atmel_serial. The only
thing left is to rename PORT_AT91 PORT_ATMEL.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Prefix all internal functions and variables with atmel_ instead of
at91_.

The at91_register_uart_fns() stuff is left as is since I can't find
any actual users of it.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Rename the following public definitions:
  * AT91_NR_UART -> ATMEL_MAX_UART
  * struct at91_uart_data -> struct atmel_uart_data
  * at91_default_console_device -> atmel_default_console_device
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Rename the "at91_usart" platform driver "atmel_usart" and update
platform devices accordingly.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Rename the following Kconfig symbols:
  * CONFIG_SERIAL_AT91 -> CONFIG_SERIAL_ATMEL
  * CONFIG_SERIAL_AT91_CONSOLE -> CONFIG_SERIAL_ATMEL_CONSOLE
  * CONFIG_SERIAL_AT91_TTYAT -> CONFIG_SERIAL_ATMEL_TTYAT
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Rename at91_serial.c atmel_serial.c
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Move include/asm/arch/at91rm9200_usart.h into drivers/serial and rename
it atmel_usart.h. Also delete AVR32's version of this file.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>