Remove unused pull-up/down data from the r8a73a4 PFC code.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

All r8a73a4 platforms use the pinctrl API to control pin functions.
Function GPIOs are no longer needed.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The r8a73a4 board support will use the pinctrl API to control the
external IRQ pins so remove the unused function GPIOS.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The r8a73a4 board support will use the pinctrl API to control the SCIF
pins, remove the corresponding unused function GPIOS.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

V2 of PINCTRL support for r8a73a4 IRQC hardware
and in particular the external pins IRQ0 -> IRQ57.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add PINCTRL support for r8a73a4 SCIF ports SCIFA0->SCIFA1 and
SCIFB0->SCIFB3.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Implement pull-up/down support for r8a73a4 similar to the implementation
for sh73a0.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

V2 of code to add GPIO -> IRQ mappings to the
PFC table for the r8a73a4 SoC. Requires the IRQs
to be mapped at a fixed location in Linux IRQ
space. The actual IRQs are not handled by the
PFC, instead IRQC is used on r8a73a4.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The r8a73a4 SoC has sparse GPIO numbers. Declare ranges for pin numbers
in the PFC SoC data. Pin numbers shall be used with the GPIO API from
this point on.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add initial PFC support for the r8a73a4 SoC.

At this point only GPIO interface is supported, move to newer interfaces
planned as incremental changes.

Original authors are Morimoto-san with help from Yoshii-san, thanks to
them for the heavy lifting. Adjusted by Magnus to work together with
updated code in drivers/pinctrl.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NTakashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The output pixel clocks can be used without the input pixel clocks.
Split them in different groups.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

GPIOs are now handled by a separate driver, remove GPIO data from the
SoC information structure.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

When a GPIO is handled by a separate driver the pinmux
gpio_set_direction() handler won't be called. The pin mux type then need
to be configured to GPIO at request time.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Boards/platforms that register dedicated GPIO devices will not supply a
memory resource for GPIOs. Try to locate the GPIO memory resource at
initialization time, and skip registration of the gpiochip if the
resource can't be found.

This is a temporary modification to ease the transition to separate GPIO
drivers. It should be reverted when all boards and platforms will have
been moved.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

When implemented as a separate IP block, GPIOs should be handled by a
separate driver. To make this possible GPIO support needs to be optional
in the sh-pfc driver.

If no GPIO data registers are supplied in the SoC information structure
skip registration of the gpiochip.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The target is to get rid of function GPIOs completely. To reach this,
make function GPIOs support optional by skipping the function GPIO chip
registration if no function GPIOS are defined in SoC data.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Refactor the GPIO macro magic to use GPIO numbers directly instead of
the GPIO_GP_x_y enum entries. This will allow removing the GPIO enum
entries from the mach/r8a7779.h header.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

All r8a7779 platforms use the pinctrl API to control functions. Function
GPIOs are unused and unneeded, remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The sh_pfc_phys_to_virt() function ends with a BUG() statement without a
return. When CONFIG_BUG isn't set the function will thus have no return
value. Fix it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

With the added capabilty of the intc_irqpin driver to handle shared
external IRQs, all prerequisites are fulfilled and we are ready to
migrate completely to GIC. This includes the following steps:

- Kconfig:	select ARM_GIC and RENESAS_INTC_IRQPIN
- intc-r8a7740: Throw out all legacy INTC code and init the GIC. We need
  		to mask out all shared IRQs as it is needed by the
		shared intc_irqpin driver.
- setup-r8a7740: Add 4 irqpin devices to handle external IRQs and update
		all IRQ numbers to point to the GIC SPI.
- board-armadillo: Update all IRQ numbers to point to the GIC SPI.
- pfc-r8a7740:	Update all IRQ numbers of the GPIOs to point to the GIC
		SPI.
Signed-off-by: NBastian Hecht <hechtb+renesas@gmail.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Adjust the sh73a0 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ31.

This removes quite a bit of special-case code
in intc-sh73a0.c but the number of lines get
replaced with platform device information in
setup-sh73a0.c. The PFC code is also adjusted
to make gpio_to_irq() return the correct
interrupt number.

At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

All r8a7779 platforms now use the pinctrl API to control the INTC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All r8a7779 platforms now use the pinctrl API to control the LBSC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All r8a7779 platforms now use the pinctrl API to control the USB pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All r8a7779 platforms now use the pinctrl API to control the HSPI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All r8a7779 platforms now use the pinctrl API to control the SCIF pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All r8a7779 platforms now use the pinctrl API to control the SDHI and
MMCIF pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

The function is not documented in the r8a7779 datasheet. Remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All r8a7740 platforms now use the pinctrl API to control the SDHI and
MMCIF pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All r8a7740 platforms now use the pinctrl API to control the LCD0 and
LCD1 pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All sh73a0 platforms now use the pinctrl API to control the IrDA pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All sh73a0 platforms now use the pinctrl API to control the USB pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All sh73a0 platforms now use the pinctrl API to control the BSC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All sh73a0 platforms now use the pinctrl API to control the KEYSC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All sh73a0 platforms now use the pinconf API to control pull-ups, the
corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All sh73a0 platforms now use the pinctrl API to control the FSI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All sh73a0 platforms now use the pinctrl API to control the I2C pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All sh73a0 platforms now use the pinctrl API to control the SCIFA and
SCIFB pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All sh73a0 platforms now use the pinctrl API to control the LCD and
LCD2 pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All sh7372 platforms now use the pinctrl API to control the SDHI and
MMCIF pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>