The platform data for the INTC irq pin driver
seems to be global symbols, make it static to
allow multi-soc build.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Adjust the sh73a0 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ31.

This removes quite a bit of special-case code
in intc-sh73a0.c but the number of lines get
replaced with platform device information in
setup-sh73a0.c. The PFC code is also adjusted
to make gpio_to_irq() return the correct
interrupt number.

At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Do not initialise any early devices when using the minimal DT reference
code. Only the delay needs to be initialised.

Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Remove warning about SMP not working with the
clock initialisation sheme used for reference DT.

This is resolved by not selecting CONFIG_PREEMPT.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This a board to be brought up with SMP enabled
without a board file present.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This is not needed as irq_set_wake is
only used for suspend to ram which is not
a requirement for bringing up boards using DT.
Reported-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds an IPMMU device and notifies the IPMMU driver which
devices are connected via the IPMMU module.  All devices connected to the main
memory bus via the IPMMU module MUST be registered when SHMOBILE_IPMMU and
SHMOBILE_IOMMU are enabled because physical address cannot be used
while the IPMMU module's MMU function is enabled.
Signed-off-by: NHideki EIRAKU <hdk@igel.co.jp>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NJoerg Roedel <joro@8bytes.org>

Allow a minimal setup of the sh73a0 SoC using a flattened device tree.
In particular, Configure the i2c controllers using a flattened device tree.

SCI serial controller and CMT clock source, whose drivers do not yet
support configuration using a flattened device tree, are still configured
using C code in order to allow booting of a board with this SoC.

*** Please note that the clock initialisation scheme used in
    this patch does not currently work with SMP as there
    is a yet to be resolved lock-up in workqueue initialisation.

    CONFIG_SMP must be disabled when using this code. ***

Includes update from Thierry Reding to no longer use gic_handle_irq()

Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

fix

Pinmux info for the sh73a0 is now provided by pinmux drivers. Remove the
duplicate copy in arch code.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.

This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html

Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

ARM is moving to stricter checks on readl/write functions,
so we need to use the correct types everywhere.

This patch is a bit ugly for shmobile, which is the only platform
that just uses integer literals all over the place, but I can't
see a better way to do this.
Acked-by: NSimon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch enables PMU(Performance Monitoring Unit) for sh73a0.
Signed-off-by: NTetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: NSimon Horman <horms@verge.net.au>

This patch switch over to use common DMAEngine definitions,
and reduced a waste of code.

It is easy to understand if sh_dmae_pdata / sh_dmae_slave_config
settings are used defined value instead of direct value.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Current shdmac can support MPDMAC (= sound DMA) on sh73a0.
This support reduce CPU load when sound was playback.

On v2.0 manual, MPDMAC MID/RID number were wrong.
This patch is using the number which seems correct.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Fix SMP TWD boot regression on sh73a0 based platforms caused by:

4200b16d ARM: shmobile: convert to twd_local_timer_register() interface

After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.

This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.

This patch removed shmobile_twd_init() which is no longer needed
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Move the SoC specific timer code from AG5EVM and Kota2
to sh73a0 setup code. This makes is possible to share
the SoC specific timer code across boards and it also
removes the need for a board specific timer structure.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Update the sh73a0 SoC and the AG5EVM and Kota2 boards to make use
of the functions sh73a0_map_io() and sh73a0_add_early_devices().
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Remove NR_IRQS and explicitly include mach/irqs.h as needed. shmobile
properly allocates irq_descs for each irqchip, so setting .nr_irqs for
each machine is not needed.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add SY-DMAC support via shdma.c to the sh73a0 SoC
including slave ids, platform data and clock bindings.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add support for 2 TMU timer channels on sh73a0.

One timer channel is used for clocksource and
the other is used for clockevents. All channels
in the same TMU block share MSTP bit as usual.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Platform device resource/data definition for CPU, and clkdev entries
Signed-off-by: NTakashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds initial support for Renesas SH-Mobile AG5.

At this point the AG5 CPU support is limited to the ARM
core, SCIF serial and a CMT timer together with L2 cache
and the GIC. The AG5EVM board also supports Ethernet.

Future patches will add support for GPIO, INTCS, CPGA
and platform data / driver updates for devices such as
IIC, LCDC, FSI, KEYSC, CEU and SDHI among others.

The code in entry-macro.S will be cleaned up when the
ARM IRQ demux code improvements have been merged.

Depends on the AG5EVM mach-type recently registered but
not yet present in arch/arm/tools/mach-types.

As the AG5EVM board comes with 512MiB memory it is
recommended to turn on HIGHMEM.

Many thanks to Yoshii-san for initial bring up.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Move SH-Mobile ARM systems over from the legacy
"clk" member of struct sh_timer_config to using
the device name and clkdev for clock matching.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch updates the irq numbers on sh7377/G4EVM
to make use of evt2irq() and intcs_evt2irq().

Makes the system cope with an updated INTCS_VECT_BASE.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add support for the sh7377 INTCA hardware block.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds preliminary support for the SH7377 (SH-Mobile G4) CPU and
the G4EVM reference board.

Only timer, serial console and NOR flash are supported at this point.
Support for the interrupt controller, pinmux support, clock framework
and runtime pm will be submitted as feature patches on top of this.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds preliminary support for the SH-Mobile G-series.

The SH-Mobile G-series is a series of ARM/SH multi-core CPUs that aside
from the ARM MPU are primarily composed of existing SH IP blocks.

This includes initial support for the SH7367 (SH-Mobile G3) CPU and
the G3EVM reference board.

Only timer, serial console, and NOR flash are supported at this point.
Patches for the interrupt controller, pinmux support, clock framework
and runtime pm will be submitted as feature patches on top of this.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>