Return 0 while probing success.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Adds support for displaying the individual pin h/w config state.
Signed-off-by: NMatt Porter <mporter@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

'pindesc' was not freed when returning from an error induced
exit path.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

fix smatch warning:
drivers/pinctrl/pinctrl-imx.c:435:21: warning: duplicate const
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Acked-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Instead of using a temporary buffer, snprintf() and kstrdup(), just
use kasprintf() that does the same thing in just oneline.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NColin Cross <ccross@google.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

With pinctrl-single,bits it is possible to update just part of the register
within the pinctrl-single,function-mask area.
This is useful when one register configures mmore than one pin's mux.

pinctrl-single,bits takes three parameters:
<reg offset, value, sub-mask>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
[Removed a misplaced comment]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Another possible pin configuration for the MC1 pin group.
Signed-off-by: NPatrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Use the pcs->fmask to make sure that the value is not changing (setting)
bits in areas where it should not.
To avoid situations like this:

pmx_dummy: pinmux@4a100040 {
	compatible = "pinctrl-single";
	reg = <0x4a100040 0x0196>;
	#address-cells = <1>;
	#size-cells = <0>;
	pinctrl-single,register-width = <16>;
	pinctrl-single,function-mask = <0x00ff>;
};

&pmx_dummy {
	pinctrl-names = "default";
	pinctrl-0 = <&board_pins>;

	board_pins: pinmux_board_pins {
		pinctrl-single,pins = <
			0x6c 0xf0f
			0x6e 0x10f
			0x70 0x23f
			0x72 0xa5f
		>;
	};
};
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

ux500 machines performs pins (GPIO) reconfiguration when entering
in the suspended mode. This reconfiguration aims at reaching an ultra
low power HW configuration.

Due to this HW reconfiguration, some HW devices can change of HW state
and have their output signals at level that could generate IRQs.

If the non-wakeup IRQs are disabled but not yet masked (delayed interrupt
disable feature from the generic irq layer), effective interrupts reach
the system only because the system attempt to enter the suspended mode.

To prevent such IRQs to trig, all irq chips embedded in ux500 platform
should enable their IRQCHIP_MASK_ON_SUSPEND flag.
Signed-off-by: NEtienne Carriere <etienne.carriere@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Unlike imx6q pinctrl driver that starts nubmering pad from 0, imx5
pinctrl drivers number pad from 1.  It causes problem/confusion when
driver accesses imx51_pinctrl_pads array using pin ID as the index.

Change imx51_pads and imx53_pads numbering start from 0.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This is mostly cut'n'paste from the imx51 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx35.h.

Changes since (implicit) v1
 - remove references to file names in binding documentation
 - remove sed commands from comments in driver
 - add explicit numbers for pins and functions
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds support for the STN8815 ASIC for the Nomadik pin
controller.
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This implements a subdriver for the DB8540 ASIC for the
Nomadik pin controller.
Signed-off-by: NPatrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.

In commit bc42aabc [2]

        commit bc42aabc
        Author: Adam Jackson <ajax@redhat.com>
        Date:   Wed May 23 16:26:54 2012 -0400

            drm/edid/quirks: ViewSonic VA2026w

Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.

All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.

Please note that this monitor only has a VGA (D-Sub) connector [1].

[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629Signed-off-by: NPaul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]

This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver.  It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board.  Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: NForest Bond <forest.bond@rapidrollout.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.

https://bugzilla.redhat.com/show_bug.cgi?id=785375Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Adjust the panel mode setup to match the behavior
of the vbios.  Rather than checking for specific
bridge chip ids, just check the eDP configuration register.
This saves extra aux transactions and works across
DP bridge chips without requiring additional per chip
id checking.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Power gating is per crtc pair, but the powergating registers
should be called individually.  The hw handles power up/down
properly.  The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down.  This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders.  We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs.  This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Some plls are shared for DP.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>

Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This should help catch uninitialized registers and reject commands
because of that.
Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

delay.h header file was included twice.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

On some Fermi chipsets (NVCE particularly) PCOPY1 doesn't exist.  And if
what I've seen on Kepler is true of Fermi too, chipsets of the same type
can have different PCOPY units available.

This should fix a v3.5 regression reported by a number of people effecting
suspend/resume on NVC8/NVCE chipsets.

Cc: stable@vger.kernel.org [3.5]
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

For unimplemented ioctls the dasd driver should return -ENOTTY.
Reported-by: NWanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: NStefan Weinhuber <wein@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

commit d70e551c, Add " 2GB ATA Flash
Disk"/"ADMA428M" to DMA blacklist, should have added a space before 2GB.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This board is incorrectly detected as having an LVDS connector,
resulting in the VGA output (the only available output on the board)
showing the console only in the top-left 1024x768 pixels, and an extra
LVDS connector appearing in X.

It's a desktop Mini-ITX board using an Atom D525 CPU with an NM10
chipset.

I've had this board for about a year, but this is the first time I
noticed the issue because I've been running it headless for most of its
life.
Signed-off-by: NCalvin Walton <calvin.walton@kepstin.ca>

The current layout is to place the per-process tables at the end of the
GTT. However, this is currently using a hardcoded maximum size for the GTT
and not taking in account limitations imposed by the BIOS. Use the value
for the total number of entries allocated in the table as provided by
the configuration registers.
Reported-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Matthew Garret <mjg@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is already fixed for ILK and SNB in the below commit but somehow
IVB is missed.

commit ab2f9df1
	Author: Jesse Barnes <jbarnes@virtuousgeek.org>
	Date:   Mon Feb 27 12:40:10 2012 -0800

	drm/i915: fix color order for BGR formats on SNB

Had the wrong bits and field definitions.
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: NAntti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Wrong order of parameters passed-in when calling hdmi/adpa
/lvds_pipe_enabled(), 2nd and 3rd parameters are reversed.

This bug was indroduced by

commit 1519b995
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Aug 6 10:35:34 2011 -0700

    drm/i915: Fix PCH port pipe select in CPT disable paths

The reachable tag for this commit is v3.1-rc1-3-g1519b995Signed-off-by: NAnhua Xu <anhua.xu@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44876Tested-by: NDaniel Schroeder <sec@dschroeder.info>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The old interface is bugged and reads the wrong sensor when retrieving
the reading for the chassis fan (it reads the CPU sensor); the new
interface works fine.
Reported-by: NGöran Uddeborg <goeran@uddeborg.se>
Cc: stable@vger.kernel.org
Tested-by: NGöran Uddeborg <goeran@uddeborg.se>
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This QUANTA device is driven by the generic hid-multitouch.ko driver, and
therefore shouldn't be in the special drivers list.

This has been an oversight in 4fa3a583 ("HID: hid-multitouch: Switch to
device groups").
Signed-off-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

It's not critical (anymore) since another thread closing the file will block
on ->device_lock before it gets to dropping the final reference, but it's
definitely cleaner that way...
Acked-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

we really need to make sure that dropping the last reference happens
under the group->device_lock; otherwise a loop (under device_lock)
might find vfio_device instance that is being freed right now, has
already dropped the last reference and waits on device_lock to exclude
the sucker from the list.
Acked-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Acked-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Acked-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>