Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
接近 2 年 前同步成功

通知 170
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 13 5月, 2016 1 次提交
  3. 09 5月, 2016 2 次提交
  5. 04 4月, 2016 1 次提交
  7. 03 4月, 2016 2 次提交
  9. 05 2月, 2016 1 次提交
    • M
      regmap: mmio: Revert to v4.4 endianness handling · 320549a2
      由 Mark Brown 提交于 
      Commit 29bb45f2 (regmap-mmio: Use native endianness for read/write)
attempted to fix some long standing bugs in the MMIO implementation for
big endian systems caused by duplicate byte swapping in both regmap and
readl()/writel() which affected MIPS systems as when they are in big
endian mode they flip the endianness of all registers in the system, not
just the CPU.  MIPS systems had worked around this by declaring regmap
using IPs as little endian which is inaccurate, unfortunately the issue
had not been reported.

Sadly the fix makes things worse rather than better.  By changing the
behaviour to match the documentation it caused behaviour changes for
other IPs which broke them and by using the __raw I/O accessors to avoid
the endianness swapping in readl()/writel() it removed some memory
ordering guarantees and could potentially generate unvirtualisable
instructions on some architectures.

Unfortunately sorting out all this mess in any half way sensible fashion
was far too invasive to go in during an -rc cycle so instead let's go
back to the old broken behaviour for v4.5, the better fixes are already
queued for v4.6.  This does mean that we keep the broken MIPS DTs for
another release but that seems the least bad way of handling the
situation.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NMark Brown <broonie@kernel.org>
      320549a2
  11. 28 1月, 2016 1 次提交
    • M
      MIPS: dt: Explicitly specify native endian behaviour for syscon · 25d6463e
      由 Mark Brown 提交于 
      On many MIPS systems the endianness of IP blocks is kept the same as
that of the CPU by the hardware.  This includes the system controllers
on these systems which are controlled via syscon which uses the regmap
API which used readl() and writel() to interact with the hardware,
meaning that all writes are converted to little endian when writing to
the hardware.  This caused a bad interaction with the regmap core in big
endian mode since it was not aware of the byte swapping and so ended up
performing little endian writes.

Unfortunately when this issue was noticed it was addressed by updating
the DT for the affected devices to specify them as little endian.  This
happened to work since it resulted in two endianness swaps which
cancelled each other out and gave little endian behaviour but meant that
the DT was clearly not accurately describing the hardware.

The intention of commit 29bb45f2 (regmap-mmio: Use native
endianness for read/write) was to fix this by making regmap default to
native endianness but this breaks most other MMIO users where the
hardware has a fixed endianness and the implementation uses the __raw
accessors which are not intended to be used outside of architecture
code.  Instead use the newly added native-endian DT property to say
exactly what we want for these systems.

Fixes: 29bb45f2 (regmap-mmio: Use native endianness for read/write)
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NMark Brown <broonie@kernel.org>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
      25d6463e
  13. 24 1月, 2016 3 次提交
  15. 04 1月, 2016 3 次提交
  17. 20 11月, 2015 1 次提交
  19. 16 11月, 2015 1 次提交
    • S
      regmap-mmio: Use native endianness for read/write · 29bb45f2
      由 Simon Arlott 提交于 
      The regmap API has an endianness setting for formatting reads and writes.
This can be set by the usual DT "little-endian" and "big-endian" properties.
To work properly the associated regmap_bus needs to read/write in native
endian.

The "syscon" DT device binding creates an mmio-based regmap_bus which
performs all reads/writes as little-endian. These values are then converted
again by regmap, which means that all of the MIPS BCM boards (which are
big-endian) have been declared as "little-endian" to get regmap to convert
them back to big-endian.

Modify regmap-mmio to use the native-endian functions __raw_read*() and
__raw_write*() instead of the little-endian functions read*() and
write*().

Modify the big-endian MIPS BCM boards to use what will now be the correct
endianness instead of pretending that the devices are little-endian.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NMark Brown <broonie@kernel.org>
      29bb45f2
  21. 11 11月, 2015 9 次提交
  23. 28 10月, 2015 1 次提交
    • R
      mips: enable building of all dtbs · 0426f648
      由 Rob Herring 提交于 
      Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
      0426f648
  25. 03 9月, 2015 1 次提交
  27. 04 8月, 2015 1 次提交
  29. 22 6月, 2015 12 次提交