* DT binding for arc-uart
* With alll the bits in place we can now use DT probing.

Note that there's a bit of kludge right now because earlyprintk portion
of driver can't use the DT infrastrcuture to get resoures/plat_data.
This requires some infrastructre changes to of_flat_ framework
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Only we meet the following conditions, we can enable the DMA support for
auart:

  (1) We enable the DMA support in the dts file, such as
      arch/arm/boot/dts/imx28.dtsi.

  (2) We enable the hardware flow control.

  (3) We use the mx28, not the mx23. Due to hardware bug(see errata: 2836),
      we can not add the DMA support to mx23.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Bindings for gpio, interrupt controller, power management controller,
timer, realtime clock, serial uart, ehci and uhci controllers and
framebuffer controllers used on the arch-vt8500 platform.

Framebuffer binding also specifies a 'display' node which is required
for determining the lcd panel data.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>

This patch adds a "compatible" string for the new 8250 UART type PORT_LPC3220.
This is necessary for initializing LPC32xx UARTs via DT.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The loopback test mode is not implemented in all
NS16550 compatible UARTs. The 8250 driver uses the
UPF_SKIP_TEST flag to indicate this, however it is
not possible to set this flag via device-tree.

Add a new 'no-loopback-test' property, and modify
the of_serial driver to set the UPF_SKIP_TEST flag
if the property is present.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow device tree probing.

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: <linux-serial@vger.kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSubodh Nijsure <snijsure@grid-net.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds a driver for the 3 High Speed UARTs of the LPC32xx SoC that
support up to 921600bps. These UARTs are different from the 4 "Standard" UARTs
of the LPC32xx.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a "compatible" string for the new 8250 UART type PORT_LPC3220.
This is necessary for initializing LPC32xx UARTs via DT.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It has been pointed out by device tree maintainer for several times
that the generic names 'serial' and 'ethernet' should be used for
those devices per ePAPR.  Renames imx uart and fec device tree nodes
to stop them being bad examples.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Generic bindings for RS485 feature included in some UARTs.
Those bindings have to be used withing an UART device tree node.
Documentation updated to link to the bindings definition.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add devicetree support to the msm_serial driver.  Clocks are still
queried by direct name from the driver until device tree clock support
is implemented.

Change-Id: Ia6b2ddfcf1e5dc3bd25dd502662f971202e6d56f
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The Synopsys DesignWare 8250 is an 8250 that has an extra interrupt that
gets raised when writing to the LCR when busy.  To handle this we need
special serial_out, serial_in and handle_irq methods.  Add a new
platform driver that uses these accessors.

Cc: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit 14a8d47d.

It causes a build error that needs to be resolved differently.

Cc: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Support the DesignWare 8250 by a new compatible string and registering
the DesignWare helpers.  If the registration of the helpers fails, then
continue as a normal 8250 as we may still get some useful debug out.

Cc: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It adds device tree probe support for imx tty/serial driver.
Signed-off-by: NJeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: NJason Liu <jason.hui@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Some platforms e.g. TI Davinci require 32-bit accesses to the UARTs.
The of_serial driver currently registers all UARTs as UPIO_MEM.  Add a
new attribute "reg-io-width" to allow the port to be registered with
different IO width requirements.
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The of_serial bindings can be used to register a number of serial
devices.  Document this binding with all of the others.

v3: remove device-type and clarify used-by-rtas
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>