The following moves the creation of IPR interupts into setup-7750.c
and updates a few other things to make it all work after the "Drop
CPU subtype IRQ headers" commit. It boots and runs fine on my titan
board.

 - adds an ipr_idx to the ipr_data and uses a function in the subtype
   code to calculate the address of the IPR registers

 - adds a function to enable individual interrupt mode for externals
   in the subtype code and calls that from the titan board code
   instead of doing it directly.

 - I changed the shift in the ipr_data to be the actual # of bits to
   shift, instead of the numnber / 4 - made it easier to match with
   the manual.
Signed-off-by: NJamie Lenehan <lenehan@twibble.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Since some header inclusion paths were cleaned up, compilation
broke. Add in the headers we need directly to build again.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This was missing for sh too, wire it up..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Follows the same change as other architectures..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds a platform device for the directly connected
CF interface on R7780RP boards, for use with the
pata_platform libata driver.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Wire up all of the essentials for lockdep..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds basic NO_IDLE_HZ support to the SH timer API so timers
are able to wire it up. Taken from the ARM version, as it fit in
to our API with very few changes needed.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Since all of the sys_timer sources currently do this on their own
within the ->get_offset() path, it's more sensible to just have
the caller take care of it when grabbing xtime_lock. Incidentally,
this is more in line with what others (ie, ARM) are doing already.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Previously this was using a static pgd shift in the reporting
code, simply flip this to PGDIR_SHIFT which does the right
thing depending on varying PTE magnitudes on the SH-X2 MMU.

While we're at it, and since it's been recently added, use
get_TTB() for fetching the TTB, rather than the open coded
instructions.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The end of the store queue bitmap is miscalculated when searching
for a free range in sq_remap(), missing the PAGE_SHIFT shift that's
done in sq_api_init(). This runs in to workloads where we can scan
beyond the end of the bitmap.

Spotted by Paul Jackson:

	http://marc.theaimsgroup.com/?l=linux-kernel&m=116493191224097&wSigned-off-by: NPaul Mundt <lethal@linux-sh.org>

This makes the early printk support somewhat more flexible,
moving the port definition to a config option, and making the
port initialization configurable for sh-ipl+g users.

At the same time, this allows us to trivially wire up the
SH7780 SCIF0, so that's thrown in too more or less for free.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There were a number of places that made evil PAGE_SIZE == 4k
assumptions that ended up breaking when trying to play with
8k and 64k page sizes, this fixes those up.

The most significant change is the way we load THREAD_SIZE,
previously this was done via:

	mov	#(THREAD_SIZE >> 8), reg
	shll8	reg

to avoid a memory access and allow the immediate load. With
a 64k PAGE_SIZE, we're out of range for the immediate load
size without resorting to special instructions available in
later ISAs (movi20s and so on). The "workaround" for this is
to bump up the shift to 10 and insert a shll2, which gives a
bit more flexibility while still being much cheaper than a
memory access.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There was a clobber issue with the register we were saving
the stack in, so we switch to a register that we handle in
the clobber list properly already.

This also follows the x86 changes for allowing the softirq
checks from hardirq context.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This extends the SH DMA API for allowing handling of DMA
channels based off of their respective capabilities.

A couple of functions are added to the existing API,
the core bits are register_chan_caps() for registering
channel capabilities, and request_dma_bycap() for fetching
a channel dynamically based off of a capability set.
Signed-off-by: NMark Glaisher <mark.glaisher@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Pass along the dev_id from request_dma() all the way down,
rather than inserting an artificial name relating to the TEI
line that we were doing before.

This makes the line a bit less obvious, but dev_id is the proper
behaviour for this regardless.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Previously we linked in the ISA DMA wrapper unconditionally.
As there are very few users of this, it's better to make it
conditional.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Handle the case where no registered DMACs exist somewhat more
gracefully. While we're at it, check for sysdev_create_file()
failing.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The implementation of system call tracing in the kernel has a
couple of ordering problems:

 - the validity of the system call number is checked before
   calling out to system call tracing code, and should be
   done after

 - the system call number used when tracing is the one the
   system call was invoked with, while the system call tracing
   code can legitimatly change the call number (for example
   strace permutes fork into clone)

This patch fixes both of these problems, and also reoders the
code slightly to make the direct path through the code the
common case.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Handle simple TLB miss faults which can be resolved completely
from the page table in assembler.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds simple push-switch support for the RDBRP-1/RDBREVRP-1 debug
boards found on the R7780RP-1.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds support for a generic push switch framework. Adaptable for
various switches, including GPIO switches and the push switches commonly
found on Renesas debug boards.

This allows switch states to be trivially reported through sysfs.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Remove extra bits from the pmd structure and store a kernel logical
address rather than a physical address. This allows it to be directly
dereferenced. Another piece of wierdness inherited from x86.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add TTB accessor functions and give it a sensible default
value. We will use this later for optimizing the fault
path.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Remove the previous saving of fault codes into the thread_struct
as they are never used, and appeared to be inherited from x86.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This fixes up the kernel for gcc4. The existing exception handlers
needed some wrapping for pt_regs access, acessing the registers
via a RELOC_HIDE() pointer.

The strcpy() issues popped up here too, so add -ffreestanding and
kill off the symbol export.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Previously big endian was simply assumed if little endian was
not set, which led to some cflags ordering issues. There's not
much point to not having a big endian option, so shove one in
a choice and wire it up in the Makefile.

This lets us clean up some of the cflags ordering while we're
at it.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Simple sem2mutex conversion for the p3map semaphores.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds some preliminary support for the SH-X2 MMU, used by
newer SH-4A parts (particularly SH7785).

This MMU implements a 'compat' mode with SH-X MMUs and an
'extended' mode for SH-X2 extended features. Extended features
include additional page sizes (8kB, 4MB, 64MB), as well as the
addition of page execute permissions.

The extended mode attributes are placed in a second data array,
which requires us to switch to 64-bit PTEs when in X2 mode.

With the addition of the exec perms, we also overhaul the mmap
prots somewhat, now that it's possible to handle them more
intelligently.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Simple 7785 placeholders to start hooking up other bits of code.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This drops the various IRQ headers that were floating around
and primarily providing hardcoded IRQ definitions for the
various CPU subtypes. This quickly got to be an unmaintainable
mess, made even more evident by the subtle breakage introduced
by the SH-2 and SH-2A changes.

Now that subtypes are able to register IRQ maps directly, just
rip all of the headers out.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

All of the various CPU subtypes currently hardcode TIMER_IRQ,
switch this to a config option in the few places we need this.

This allows further removal of hardcoded IRQ headers..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The nommu patches broke the path for the common bits, get it building
for the SH-3/4 case again.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

A number of API changes happened underneath the 7206 patches, update
for everything that broke.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds support for the Solution Engine 7206 and 7619.
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This splits out common bits from the existing exception handler for
use between SH-2/SH-2A and SH-3/4, and adds support for the SH-2/2A
exceptions.
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH-2A has special division hardware as opposed to a full-fledged FPU,
wire up the exception handlers for this.
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This implements initial support for the SH7206 (SH-2A) and SH7619
(SH-2) MMU-less CPUs.
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>