- 13 2月, 2010 35 次提交
-
-
由 Mike McCormack 提交于
Move hardware initialization into sky2_hw_up. Signed-off-by: NMike McCormack <mikem@ring3k.org> Acked-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Mike McCormack 提交于
Allocate everything in one place so there's a single point of failure in sky2_up, and sky2_rx_start can no longer fail. Don't leave the hardware in a partially initialized state in the case rx ring allocation fails. As with the old code, the rx ring still needs to be fully allocated for sky2_up to succeed. Signed-off-by: NMike McCormack <mikem@ring3k.org> Acked-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Mike McCormack 提交于
Move code to calculate receive threshold and packet size out of sky2_rx_start() so that is can be called from elsewhere easily. Signed-off-by: NMike McCormack <mikem@ring3k.org> Acked-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Change how FIFO is programmed in jumbo mode (to match vendor driver). Mostly cosmetic, the only register change is that the bits 22,23 are not programemd used. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
This bit is not changed by vendor driver, and should be left alone. The documentation implies this a debug bit. 0 = WAKE# only asserted when VMAIN not available 1 = WAKE# is depend on wake events and independent of VMAIN. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Change Wake On Lan code to be similar to vendor driver. The definition of Y2_HW_WOL_ON is confusing; what it means is transition to firmware SPI setting when doing power change. Since same code is done for both shutdown and suspend, use common code path. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Warning about hidden variable Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 jamal 提交于
kernel side should use uxx instead of __uxx types Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 jamal 提交于
Some XFRM attributes were not going through basic validation. Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Convert QPRINTK macros to netif_<level> equivalents. Expands and standardizes the logging message output. Removes __func__ from most logging messages. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Convert uses of msg_<type> to netif_<level>( Remove msg_<type> macros Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Simplify the logic a bit, make the message logs a bit more consistent. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Add macros to test a private structure for msg_enable bits and the netif_msg_##bit to test and call netdev_printk if set Simplifies logic in callers and adds message logging consistency Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Logging messages sometimes had duplicated "ATL1E" output. For instance: ATL1E 0000:03:00.0: ATL1E: eth0 NIC Link is Up<100 Mbps Full Duplex> is now: ATL1E 0000:03:00.0: eth0: NIC Link is Up <100 Mbps Full Duplex> Add some consistency to logging messages Add some missing \n's to logging messages Miscellaneous typo spelling corrections Change atl1e_validate_option argument from pdev to adapter Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
These netdev_printk routines take a struct net_device * and emit dev_printk logging messages adding "%s: " ... netdev->dev.parent to the dev_printk format and arguments. This can create some uniformity in the output message log. These helpers should not be used until a successful alloc_netdev. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Don't need to disable bottom half it is already down in the previous lock. Move some blank lines to group locking in same context. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Permanent IPV6 addresses should not be removed when the link is set to admin down, only when device is removed. When link is lost permanent addresses should be marked as tentative so that when link comes back they are subject to duplicate address detection (if DAD was enabled for that address). Other routing systems keep manually configured IPv6 addresses when link is set down. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
The offset to read the eeprom data was missing and wrong eeprom data was being dumped. This patch fixes this. >From Suresh R <sureshr@serverengines.com> Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Since the driver is supporting multiple generations of the ASIC don't mention any ASIC generation number. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Since the driver is supporting multiple generations of the ASIC remove ASIC generation information from the driver description. This information is displayed by modinfo. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
In certain skews the ASIC can support only 16 vlans per interface. Once the limit is crossed, the ASIC is programmed in vlan promiscuous mode. Switch off the vlan promiscuous mode once the number of vlans falls back to the max vlans supported. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Couple of code optimizations in the Rx path (to avoid a memset). From: Sathya P <sathyap@serverengines.com> Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Current code allows the new mtu to cross the supported value. This patch fixes the boundary checks. From: Suresh R <sureshr@serverengines.com> Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Now flashing both BE2 and BE3 devices is supported. From: Naresh G <nareshg@serverengines.com> Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
We are not going to use this device id. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shirley Ma 提交于
Now we have a virtio detach API (in commit f9bfbebf), we don't need to track xmit skbs in the virio_net driver, which improves transmission performance. Signed-off-by: NShirley Ma <xma@us.ibm.com> Acked-by: NRusty Russell <rusty@rustcorp.com.au> Acked-by: NMichael S. Tsirkin <mst@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tristram Ha 提交于
Add Micrel KSZ884X network driver for KSZ8841/KSZ8842 PCI Ethernet chips. Signed-off-by: NTristram Ha <Tristram.Ha@micrel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tristram Ha 提交于
Add Micrel KSZ8841/KSZ8842 PCI Ethernet chip support. Signed-off-by: NTristram Ha <Tristram.Ha@micrel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tristram Ha 提交于
This is a new network driver for Micrel KSZ8841/KSZ8842 PCI Ethernet chips. The same driver can run both chips at the same time. It supports IPv4 TCP hardware checksumming and so can use scatter/gather transmission. The KSZ8842 switch has 2 ports. Some users like to take direct control of those ports. So KSZ8842 has a multiple devices mode in which the driver creates another network device so that users can specify which port to send packets. This mode is enabled by passing the "multi_dev=1" parameter to the driver during loading. The KSZ884X can receive huge frames with size up to 1916 bytes. To use this feature change the network device MTU from 1500 to 1898. The KSZ884X driver has 3 packet receive processing functions for the normal mode, multiple devices mode, and huge frame mode. Those functions are identical except for more checking for the new features. In normal programming point of view the huge frame version is the one to use because it covers all the cases, but this is done for performance consideration because the target clients for the KSZ884X chips are embedded systems, which unlike desktop PC may not have powerful CPU. Signed-off-by: NTristram Ha <Tristram.Ha@micrel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Uwe Kleine-König 提交于
A pointer to am79c961_probe is passed to the core via platform_driver_register and so the function must not disappear when the .init sections are discarded. Otherwise (if also having HOTPLUG=y) unbinding and binding a device to the driver via sysfs will result in an oops as does a device being registered late. An alternative to this patch is using platform_driver_probe instead of platform_driver_register plus removing the pointer to the probe function from the struct platform_driver. Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Patrick McHardy 提交于
When the fib size exceeds what can be dumped in a single skb, the dump is suspended and resumed once the last skb has been received by userspace. When the fib is changed while the dump is suspended, the walker might contain stale pointers, causing a crash when the dump is resumed. BUG: unable to handle kernel NULL pointer dereference at 0000000000000018 IP: [<ffffffffa01bce04>] fib6_walk_continue+0xbb/0x124 [ipv6] PGD 5347a067 PUD 65c7067 PMD 0 Oops: 0000 [#1] PREEMPT SMP ... RIP: 0010:[<ffffffffa01bce04>] [<ffffffffa01bce04>] fib6_walk_continue+0xbb/0x124 [ipv6] ... Call Trace: [<ffffffff8104aca3>] ? mutex_spin_on_owner+0x59/0x71 [<ffffffffa01bd105>] inet6_dump_fib+0x11b/0x1b9 [ipv6] [<ffffffff81371af4>] netlink_dump+0x5b/0x19e [<ffffffff8134f288>] ? consume_skb+0x28/0x2a [<ffffffff81373b69>] netlink_recvmsg+0x1ab/0x2c6 [<ffffffff81372781>] ? netlink_unicast+0xfa/0x151 [<ffffffff813483e0>] __sock_recvmsg+0x6d/0x79 [<ffffffff81348a53>] sock_recvmsg+0xca/0xe3 [<ffffffff81066d4b>] ? autoremove_wake_function+0x0/0x38 [<ffffffff811ed1f8>] ? radix_tree_lookup_slot+0xe/0x10 [<ffffffff810b3ed7>] ? find_get_page+0x90/0xa5 [<ffffffff810b5dc5>] ? filemap_fault+0x201/0x34f [<ffffffff810ef152>] ? fget_light+0x2f/0xac [<ffffffff813519e7>] ? verify_iovec+0x4f/0x94 [<ffffffff81349a65>] sys_recvmsg+0x14d/0x223 Store the serial number when beginning to walk the fib and reload pointers when continuing to walk after a change occured. Similar to other dumping functions, this might cause unrelated entries to be missed when entries are deleted. Tested-by: NBen Greear <greearb@candelatech.com> Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gerrit Renker 提交于
This fixes a problem in the DCCP getsockopt() API: currently there is no way for a user to a priori know the number of built-in CCIDs, other than trying DCCP_SOCKOPT_AVAILABLE_CCIDS in a loop, incrementing the option length until EINVAL is no longer returned. This patch truncates the array to the user-provided length. No copy is made when the length is <= 0. Due to the length restriction in do_dccp_getsockopt() to sizeof(int), the minimum array length remains 4, which is a reasonable default (only 3 CCIDs, CCID-2..4, are currently defined). Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
Use "phy_find_first" instead of manual lookup. Also use "phy_connect_direct" instead of "phy_connect" since we already have phy_device pointer here. Signed-off-by: NJiri Pirko <jpirko@redhat.com> Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss anything). Used spatch and did small tweaks and conding style changes when it was suitable. Jirka Signed-off-by: NJiri Pirko <jpirko@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 2月, 2010 1 次提交
-
-
由 Roland Dreier 提交于
Initialize the .cmd member of various ethtool using a designated struct initializer rather. This makes things a teeny bit more robust, although the chance of a struct layout changing is extremely remote, and also makes the code a little easier to read. Signed-off-by: NRoland Dreier <rolandd@cisco.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 2月, 2010 4 次提交
-
-
由 Peter Waskiewicz 提交于
Driver has gone under significant changes, the version should reflect that. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter Waskiewicz 提交于
This patch adds n-tuple filter programming to 82599. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter P Waskiewicz Jr 提交于
This patchset enables the ethtool layer to program n-tuple filters to an underlying device. The idea is to allow capable hardware to have static rules applied that can assist steering flows into appropriate queues. Hardware that is known to support these types of filters today are ixgbe and niu. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Break the largish case for handling receive checksum into a separate function, and if there is a problem use dev_XXX routines to show which hardware is the problem. Turn one corner case into a BUG(). This only happens if the driver is expecting one behavior but the chip does the old behavior; only ever saw this when bringing up a new chip type and driver was buggy. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-