If an error is detected after mac80211 is already suspended, the recovery
work will not be queued. This will leave the driver in a bad state on
resume.

Detect this in the resume op and re-queue a recovery.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Set a flag and after the first read/write failure is encountered.
This flag will disallow further SDIO read/writes until op_stop() is
executed, which will clear all flags.

This prevents further errors from occurring, since one error usually
indicates that IO operations won't work anymore until the chip is
rebooted.  By blocking more calls, we avoid extra timeouts and having
to wait for them to occur.

[Added second paragraph explaining why the change is needed. -- Luca]
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We wish to postpone suspend if recovery is pending. This will make sure
the FW is in a good state and perform wowlan wakeup.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Applications running in the user space needs access to the
memory of the chip. Examples of such access
- read/write global variables
- access to firmware log
- dump memory after firmware panic event

Arbitrary 4-bytes aligned location can be accessed by
read/write file wlcore/mem

[Check return value of wlcore_raw_read/write and wlcore_set_partition
calls as required by the recent IO changes. -- Luca]
Signed-off-by: NArkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

All io functions' return values should be propagated and handled. Add a
__must_check annotation to verify that the return values are checked and
to avoid future mistakes.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Propagate errors from wl1271_read_hwaddr. This function is only used
when reading the FW log (following a recovery), so don't read the FW log
in case of a bus error.

Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Propagate errors from wl1271_raw_write32 and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Propagate errors from wl1271_raw_read32. Since the read functions had no
way of returning errors in-band, change their prototypes.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Propagate errors from wl1271_write and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Propagate errors from wl1271_read and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wlcore_raw_read_data is called when the FW status is read which happens
while handling interrupts and when the FW log is read following a
recovery. Request a recovery in the former case, and don't read the FW
log in case the FW status read failed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Make wl1271_raw_write and wl1271_raw_read return errors so the driver
could handle these appropriately.
Since the prototype has changed, also rename the prefix of these
functions to wlcore.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

While bus operations may fail, either due to HW or FW issues, these are
never propagated to higher layers. As a result, the core driver has no
way of knowing that the operations failed, and will only recover if high
level logic requires it (e.g. no command completion).

Change read/write bus operations to return errors to let higher layer
functionality handle these.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In case a recovery is initiated, the FW can no longer be trusted, and
the driver should not handle any new FW events.

Disable the interrupt handler when a recovery is scheduled and balance
it back in the op_stop callback.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wl12xx_sdio_power_off() manually powers down the card regardless of the
runtime pm state. If wl12xx_sdio_power_on() is called before the card
was suspended by runtime PM, it will not power up the card.

As part of the HW detection, the chip's power is toggled. Since this
happens in the context of probing sdio, the power reference counter will
be higher than zero. As a result, when wl12xx_sdio_power_off() is
called, the chip will be powered down while still having a positive
power reference counter. If the interface is quickly activated, the
driver might try to transfer data to a powered off chip.

Fix this by ensuring that wl12xx_sdio_power_on() explicitly powers on
the chip in case runtime pm claims the chip is already powered on. To
avoid cases in which it is not possible to determine if the chip was
really powered on (card's power reference counter is positive), operate
on the mmc_card instead of the function.

Also verify that the chip is indeed powered on before powering off, to
avoid wrong reference counter values in error cases.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

After 934b9d1e (wl18xx: avoid some -Wformat warnings) there was still
a warning with (at least) ARM gcc version 4.4.1:

drivers/net/wireless/ti/wl18xx/main.c: In function 'wl18xx_conf_init':
drivers/net/wireless/ti/wl18xx/main.c:1026: warning: format '%ld' expects type 'long int', but argument 2 has type 'unsigned int'

Fix this by using %zu for the both formats, since the fw->size and the
macro (derived from sizeof()) are size_t.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Remove the cap IEEE80211_HT_CAP_DSSSCCK40 from the 5Ghz variant of
the siso40 HT capabilities. It is meaningless in 5Ghz.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Introduce a default set of HT capabilities that are set according to the
number of antennas on the board. Move the HT setting code down to allow
the number of antennas to be set (and optionally overridden) before it.

Remove the "mimo" HT option, since the default mode now enables MIMO is
possible.

Use this opportunity to add a helper function for setting HT
capabilities and reduce the volume of the code a bit.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The 18xx chip does not support MIMO in 5Ghz. Use the siso20 HT cap as
fallback in 5Ghz when "mimo" is requested.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

FW uses a few memory blocks as a buffer to accumulate FW logs before
transmitting them to the host over SDIO. When FW WatchDog recovery
occurs, the last FW traces are still pending in the buffer. Driver is
to read these FW traces whether log mode is continuous or on demand.

FW memory blocks allocated for the log buffer are handled as a link list:
the first 4 bytes in each memory block contain FW address to the next block.
The end of list condition depends on FW log mode:
- on demand: the list is cyclic, the next address is equal to the first address
- continuous: the address is  equal to 0x2000000

Log data resides inside FW memory block with offset depending on
logger mode:
- on demand:  4 bytes (address of the next memory block)
- continuous: 4 bytes and Rx Descriptor structure size

Described FW logger API is backward compatible with previous FW versions.
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The get survey op expects the low level driver to report
the noise level for a a given channel.

The noise calculated in wlcore is (rssi-snr/2), but since
the snr reported by the FW is a derivative from the rssi
this calculation is useless, and should not be reported
to the user space.

Reporting incorrect noise, results in the wpa_supplicant
miscalculating the roaming candidate priority, thus causing
a situation where an AP with a lower rssi level would be
chosen over a better AP.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Before patch b5d6d9b2 (wlcore/wl12xx/wl18xx: don't use TX align quirk
for wl127x), this was automatically set for all platforms. As this
should now be set explicitly, set it for PG2 as well.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

New PG2 firmwares have additional Rx descriptors.

Add a module parameter to manually set the number of Rx descriptors for
older versions (PG1). We cannot discriminate based on chip-id, since
this value must be set on probe.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The sleep_auth value of the last interface to be set up prevailed when
an interface was removed. Take care of this by correctly configuring the
value according to the remaining STA/AP interfaces.

Take this opportunity to refactor the sleep_auth setting code for better
readability.

[Small style fix. -- Luca]
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Hold a value for sta_sleep_auth that is amenable to change by debugfs.
When detecting a legal value in this variable on interface init, use it
as an override value for sleep_auth.

This makes debugging more intuitive using the debugfs value.

Increment the conf version since we added an element to the conf
structure.

Note: An AP going up will always set sleep_auth to PSM_CAM.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

For FW debugging purposes, we may need to change the sleep mode
(aka. sleep_auth) by hand, and set it to the mode we want.  To allow
this, a debugfs entry is added.

Now we store the sleep_auth value that has been set and use that
instead of the quirk to decide whether we should enter ELP or not.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

The ampdu_action() function is called on the reconfig() path to remove
existing Rx BA sessions. Since these don't exist for the low level
driver, we output an error message. Turn the message into a debug
message for now, until the mac80211 reconfig flow is changed.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Advertise to the stack that the wlcore driver
supports multiple interfaces for a single device.
This is required in order to be able to run
multirole with mac80211.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

FEM BIP calibration may fail with fw/phy radio status. In order to
recognize these failures a log is added to the calibration answer
(TEST_CMD_P2G_CAL)
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add support for HP (High Performance TQS fem type 3) and SKW
(fem type 2). This is done by increasing the number of FEM
manufacturers to 4.

Usually FEM parameters from ini file are read from nvs file and
passed to firmware using TEST_CMD_INI_FILE_RADIO_PARAM. Still,
because the nvs file has only place for 2 FEMs, we need to pass the
new FEM types information in one of the available entries.

This is done by mapping new fem types 2,3 to entry 0. This solution
works for manual FEM selection. AutoDetect-FEM still support only
fem types 0 and 1.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

On channel switch we have to update the basic rates, in
order to reflect possible band changes (otherwise, we
might start beaconing on 11a with the default rates
of 11g).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

EAPOLs are sent at high rates as they are considered
data packets. Some APs like Motorola Symbol AP7131 and AP650
don't respond well to these rates and don't respond with
EAPOL 3/4 consistently. When sending EAPOL 2/4 at 54Mbps
we've seen approx 30% success rate in getting EAPOL 3/4 response
while using 11Mbps we got 100% success.
To increase the chances of successful 4-Way handshake with
such APs, send EAPOLs with basic rate policy in order to avoid
high rates.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

NET_IP_ALIGN can be overriden on different architectures
and therefore cannot be used in the RX path to account
for the 2 bytes added for alignment (either by the FW
in the case of 18xx or by the host for 12xx).
Instead use an internal define.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Don't spew errors when we can't find the NVS file in wlcore. Instead
fail the wl12xx boot HW op if the NVS isn't found.

Take this opportunity to remove some dead code from register_hw()
which looks for the NVS again needlessly.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Give all wl18xx phy module paramters -1 as a default value, indicating
the paramter was not set. Add previous default values to the default
18xx priv conf structure.

Remove the board_type field from wl18xx priv. The field with the same
name inside the phy conf is good enough for our purposes.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wl18xx_conf_phy represents part of the FW native wl18xx_mac_and_phy_params
structure. Remove it and replace the phy part of the wl18xx conf with the
FW bound structure. This allows us to set/override all members.

Increment the wlconf version to ensure compatibility with the new
structure
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Aligned to the struct in FW 8.2.0.0.91 and updated the debugfs entries
accordingly.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This is supported by new FW versions (.88+).
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Instead of using the hardcoded configuration structure, try to read it
from a "firmware" file called wl18xx-conf.bin.  If the file doesn't
exist, fall back to the hardcoded version.  If the file exists but is
illegal, bail out.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add conf file header structure, magic and version values and export
the entire conf struct in debugfs.
Signed-off-by: NLuciano Coelho <coelho@ti.com>